1021 Atlantic Blvd Unit 19 ROOF21-0008 NonshingleOWNER:ADDRESS:CITY:STATE:ZIP:
EQUITY ONE ATLANTIC
VILLAGE INC 1600 NE MIAMI GARDENS DR NORTH MIAMI
BEACH FL 33179
COMPANY:ADDRESS:CITY:STATE:ZIP:
ROOF CONTROL SERVICES 11748 OSPREY POINT BLVD CLERMONT FL 34711
TYPE OF
CONSTRUCTION:
REAL ESTATE
NUMBER:ZONING:BUILDING USE
GROUP:SUBDIVISION:
177602 0040 SECTION LAND
JOB ADDRESS:PERMIT TYPE:DESCRIPTION: VALUE OF WORK:
1021 ATLANTIC BLVD 953-
975 ROOF NON SHINGLE MODIFIED BITUMEN -Unit
19 SOLA SALON $86451.00
LIST OF CONDITIONS
Roll off container company must be on City approved list . Container cannot be placed on City right-of-way.
1 BUILDING ROOF IN-PROGRESS INSPECTION REQUIRED INFORMATIONAL
Notes:
a. The roof sheathing for all new construction must remain uncovered until the Roof Sheathing Inspection is approved.
b. All roofing projects require an In-Progress Inspection.
c. Sheathing installation and replacement guidelines per APA.
d. Underlayment must conform to FBC-R Table 905.1.1
e. Shingles must conform to ASTM D3161 G or H, or ASTM D7158 F
NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property
that may be found in the public records of this county, and there may be additional permits required from other
governmental entities such as water management districts, state agencies, or federal agencies.
WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN
YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT
MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU
INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE
RECORDING YOUR NOTICE OF COMMENCEMENT.
MUST CALL INSPECTION PHONE LINE (904) 247-5814 BY 4 PM FOR NEXT DAY INSPECTION.
ALL WORK MUST CONFORM TO THE CURRENT 6TH EDITION (2017) OF THE FLORIDA BUILDING
CODE, NEC, IPMC, AND CITY OF ATLANTIC BEACH CODE OF ORDINANCES .
ALL CONDITIONS OF PERMIT APPLY, PLEASE READ CAREFULLY.
1 of 2Issued Date: 2/23/2021
PERMIT NUMBER
ROOF21-0008
ISSUED: 2/23/2021
EXPIRES: 8/22/2021
ROOF NON SHINGLE PERMIT
CITY OF ATLANTIC BEACH
800 SEMINOLE ROAD
ATLANTIC BEACH, FL 32233
FEES
DESCRIPTION ACCOUNT QUANTITY PAID AMOUNT
BUILDING PERMIT 455-0000-322-1000 0 $428.00
BUILDING PLAN CHECK 455-0000-322-1001 0 $214.00
STATE DBPR SURCHARGE 455-0000-208-0700 0 $9.63
STATE DCA SURCHARGE 455-0000-208-0600 0 $6.42
TOTAL: $658.05
2 of 2Issued Date: 2/23/2021
PERMIT NUMBER
ROOF21-0008
ISSUED: 2/23/2021
EXPIRES: 8/22/2021
ROOF NON SHINGLE PERMIT
CITY OF ATLANTIC BEACH
800 SEMINOLE ROAD
ATLANTIC BEACH, FL 32233
DESCRIPTION ACCOUNT QTY PAID
PermitTRAK $658.05
ROOF21-0008 Address: 1021 ATLANTIC BLVD 953-975 APN: 177602 0040 $658.05
BUILDING $428.00
BUILDING PERMIT 455-0000-322-1000 0 $428.00
BUILDING PLAN REVIEW $214.00
BUILDING PLAN CHECK 455-0000-322-1001 0 $214.00
STATE SURCHARGES $16.05
STATE DBPR SURCHARGE 455-0000-208-0700 0 $9.63
STATE DCA SURCHARGE 455-0000-208-0600 0 $6.42
TOTAL FEES PAID BY RECEIPT: R14987 $658.05
Printed: Tuesday, February 23, 2021 2:30 PM
Date Paid: Tuesday, February 23, 2021
Paid By: ROOF CONTROL SERVICES
Pay Method: CREDIT CARD 426475771
1 of 1
Cashier: CG
Cash Register Receipt
City of Atlantic Beach
Receipt Number
R14987
ROOF21-0008
General Scope for Atlantic Village, Units 1-10:
Existing roof is a gravel-surfaced BUR over 1.50" perlite.
Scope:
a) Vacuum the loose gravel from the roof.
b) Install/ mechanically attach 1" ISO board (6-fasteners per board).
c) Install Soprafix System:
i) Mechanically Attached a Base Ply (Soprema 612) in seam at 12" oc with 4" overlap,
then torch or heat weld the seam closed (see attached PDF. Increased fastener
enhancements at perimeter and corners -see attached base faster enhancement
diagram).
ii) Soprema, the roof system manufacturer to perform an in-progress inspection of the
base layer.
iii) Torch apply a cap sheet (Sopralene Flam 180 FR GR).
iv) Soprema, the roof system manufacturer, to perform a final inspection following cap-
sheet installation, and completion of all penetration flashings.
-Terminate front and side-wall flashings with both t-bar and counterflashing combo at 12" oc;
Flashing of existing penetrations: Approximately four-(4) roof curbs (approximately 2'x4'
in size).
Approximately eight-(8) pipes and/or pitch-pans.
Submit Surcharge Stats & racts Publications Contact Us BCIS Site Map Links Search
Product Approval
USER: Public User
£'.!:Qduct_tl~Menu > Product or Application Searcl·, > P.&Q)1_£at1on Li§!> Application Detail
FL#
Application Type
Code Version
Application Status
Comments
Archived
Product Manufacturer
Address/Phone/Email
Authorized Signature
Technical Representative
Address/Phone/Email
Quality Assurance Representative
Address/Phone/Email
Category
Subcategory
Compliance Method
Florida Engineer or Architect Name who developed
the Evaluation Report
Florida License
Quality Assurance Entity
Quality Assurance Contract Expiration Date
Validated By
Certificate of Independence
Referenced Standard and Year (of Standard)
Equivalence of Product Standards
Certified By
FL3915-R27
Revision
2017
Approved
Soprema, Inc.
310 Quadral Drive
Wadsworth, OH 44281
(800) 356-3521
dperry@soprema.us
Darren Perry
dperry@soprema.us
Darren Perry
3010 Pinecrest Drive
Greenville, NC 27858
(252) 414-3020
dperry@soprema.us
Roofing
Modified Bitumen Roof System
Evaluation Report from a Florida Registered Architect or a Licensed
Florida Professional Engineer
Evaluation Report -Hardcopy Received
Robert Nieminen
PE-59166
UL LLC
04/02/2022
John W. Knezevich, PE
Validation Checklist -Hardcopy Received
fL391;2._8,27 COI 2019 01 COl NIEMif\lEN.pdf
Standard
ASTM D6162
ASTM D6163
ASTM D6164
ASTM D6298
FM 4470
FM 4474
Year
2008
2008
2011
2005
2012
2011
Sections from the Code
Product Approval Method
Date Submitted
Date Validated
Date Pending FBC Approval
Date Approved
Summary of Products
FL# Model, Number or Name
Method 1 Option D
02/14/2019
02/18/2019
02/22/2019
04/16/2019
Description
3915.1 Soprema Modified Bitumen Roof Modified Bitumen Roof Systems
Systems
Limits of Use Installation Instructions
Approved for use in HVHZ: No FL39l5 R27 II 2019 02 FINAL Al ER
Approved for use outside HVHZ: Yes B.27.pdf
Impact Resistant: N/A Verified By: Robert Nieminen PE-59166
Design Pressure: +N/A/-650 Created by Independent Third Party: Yes
Other: 1.) The design pressure noted in this application Evaluation Reports
SOP8.EMA FL39l5-
pertains to a particular assembly. Refer to ER Appendix for all FL3915 R27 AE 2019 02 FINAL ER SOPREMA FL39l5-
assemblies and max. design pressures. 2.) Refer to ER R27.pdf
Section 5 for Limits of Use. Created by Independent Third Party: Yes
DD
Contact Us:: 2601 Blair Stone Road Tallahassee FL 32399 Phone: 850-487-1824
The State of Florida is an AA/EEO employer. Copyright 2007-2013 State of Florida. : : Privacy Statement : : Accessibility Statement : : Refund Statement
Under Florida law, email addresses are public records. If you do not want your e-mail address released in response to a public-records request, do not send electronic
mail to this entity. Instead, contact the office by phone or by traditional mail. If you have any questions, please contact 850.487.1395. *Pursuant to Section
455.275(1), Florida Statutes, effective October 1, 2012, licensees licensed under Chapter 455, F.S. must provide the Department with an email address if they have
one. The emails provided may be used for official communication with the licensee. However email addresses are public record. If you do not wish to supply a
personal address, please provide the Department with an email address which can be made available to the public. To determine if you are a licensee under Chapter
455, F.S., please click here .
Product Approval Accepts:
[ill~
Credit Card
Safe
SOPRAFX
1\/1ECHAI\JICAUY FASTE~JEC TV\/0-PLY
SBS-1\/iOCIFIED 81TUfv1E1\J MEMBRA:\JE SYSTEM
II 13tlii!hiii~!;I ®#R11436 <e>
APPROVED
I
l SOPRAFIX BASE PLY
Soprafix Base 611 (New))
Soprafix Base 612 (Soprafix S) 4
; Soprafix Base 613 (Soprafix F) 4
!. S.°.?..rafix Base_614 (S?.prafix X) 4
HEAT APPLIED CAP PLY
AREA
(SQ)1
MAXIMUM THICKNESS TOP SIDE LAP AVAILABLE
(MILS) 2 SURFACE TREATMENT RATING 3
1.5 98 Poly film Heat weld FM 1-285
1.0 118 Poly film Heatweld FM 1-285
1.0 118 Poly film Heat weld FM 1-150
1.0 157 Poly film Heat weld FM 1-345 ........ ; .... -------+----------;
AREA THICKNESS TOP BOTTOM FIRE
(SQ) 1 (MILS) 2 SURFACE SURFACE CLASSIFICATION 3
Soprastar Flam 1.0 138 Bright white film Poly film 2:12 Class A
Elastophene Flam LS FR GR 1.0 130 Granules Poly film 1/2:12 Class A
1-------------~----+-----+-------------+--------,
f-S_o_p_ra_le_ne_F_l_am_18_0_F_R_G_R _______ 1_.0 ____ 1
1
5
5
_7
7
__ ....... 1
1
..... _G_r_an_u_le_s _ -~-P_o_ly_fi_lm_---+--·-1 :_12_C_l_as_s_A
I Sopralene Flam 180 FR+ GR 1.0 Granules Poly film 2:12 Class A
I Sopralene Flam 180 Ultra FR GR 1.0 ... ~.~! ......... J ... _G_r_a_nu_le_s_~ __ Po_ly_fi_1lm_~ 3:12 Class A
SOPRAFIX BASE PLY AREA
(SQ)1
Soprafix Base 622 (Soprafix) 4 1.0 102
Soprafix Base 641 (Soprafix E) 4 1.0 110
ADHESIVE APPLIED CAP PLY AREA THICKNESS
(SQ)1 (MILS)2
Soprastar Sanded 1.0 138
Elastophene LS FR GR 1.0 136
Sopralene 180 FR GR 1.0 157
Sopralene 180 FR+ GR 1.0 157 ..........
Sopralene 180 Ultra FR GR 1.0 157
I
SOPRAFIX BASE PLY AREA THICKNESS I
(SQ)1 (MILS)2
Soprafix Base 641 (Soprafix E) 4 1.0 110
SELF-ADHERED CAP PLY AREA THICKNESS
(SQ)1 (MILS) 2
··········------.. .--.,.-..
Elastophene Stick HR FR GR 1.0 138
LIL r'.ili:;mi .. Da(!e J11c FBC fr,r E:v~ilslilE; r:1tinqs Sr-•(-produc~
\"·r(:'Vl(JU$ tcdE, n:::.n1f .) .. pl~, p,{,..E:ntl·!E!~~es
TOP
SURFACE
Sanded
Sanded
TOP
SURFACE
Bright white film
Granules
Granules
Granules
Granules
TOP
SURFACE
Sanded
TOP
SURFACE
Granules
SIDE LAP
TREATMENT
Heat weld
Self-adhered
BOTTOM
SURFACE
Sanded
Sanded
Sanded
Sanded
Sanded
SIDE LAP
TREATMENT
Self-adhered
BOTTOM
SURFACE
Release film
lc.ipwrdlh
FM 1-285
FM 1-180
FIRE
CLASSIFICATION 3
2:12 Class A
1/2:12 Class A
1 :12 Class A
2:12 Class A
3:12 Class A
MAXIMUM
AVAILABLE
RATING 3
FM 1-180
FIRE
CLASSIFICATION 3
3/4:12 Class A
SOPREMA INC.
310 Quadral Drive
Wadsworth, Ohio 44256
800.356.3521
www.soprema.us
Fasten the Soprafix SBS
base ply side laps in
accordance with
industry approvals and
SOP REMA instructions.*
*SOPREMA's patented Tri-Fixx fastening system
is ideal for lightweight insulating concrete
applications providing superior wind ratings.
Seal the full width of the
Soprafix SBS base ply side lap.
Install the SBS base
flashing ply.
Install the SBS capply. SBS
Cap ply options indude heat
welding, cold adhesive and
self-adhered applications.
Install SBS cap flashing.
JdB COPY
DESCR IPT I ON & f=EA TURES ........................................... _ .... _ ................................................................................... ·---...... ......... ........ ....................... ........... .... ............... . .. _ .. _ ........................................... .
SOPRALENE Flam 180 FR GR (fire retardant , granulated) is an SBS-modified bitumen cap
ply for use in approved multi -ply membrane and flashing assemblies . SOPRALENE Flam
180 FR GR is composed of a proprietary formulation of elastomeric styrene-butadiene-
styrene (SBS) polymer modified bitumen and is reinforced with a tough , dimensionally
stable non-woven polyester mat. The topside is surfaced with ceramic coated granules
and underside is surfaced with polyolefin burn-off film to optimize heat welding.
SOPRALENE Flam 180 FR GR includes the standard white granules. Contact SOPREMA ® Customer
Service or your sales representative for other granule color options and special order requirements.
STORAGE & HANDLING
Store rolls on end and maintain in an upright position to prevent damage. Store rolls
in a clean dry location and cover as necessary to protect rolls from environmental
damage such as extreme cold, heat , or moisture. Monitor varying environmental
conditions during storage, handling and application of SOPRALENE Flam 180 FR GR.
APPLICATIOf\J .................................. ___ ..... .., ............... -.................................................... ___ _ _ __ ............................................................................ -...... .
Prior to installation, unroll SOPRALENE Flam 180 FR GR onto the roof surface and allow
to relax. Position SOPRALENE Flam 180 FR GR in desired position and back roll the
product. SOPRALENE Flam 180 FR GR is then heat welded to approved substrates.
Refer to the SOPREMA SBS Roofing Installation Guide for additional application
guidelines.
SOPRALENE Flam 180 FR GR 0 .27 0.24
Standard white granules (WH) initial 3 year
SOPRALENE Flam 180 FR GR 0.66 0.62*
Highly reflective white granules (SG) initial 3 year
HEAT-WELDED SOPRALENE Flam 180 FR GR 0.10 N/A .• Smog reducing granules (EC03) initial **
*CRRC Rapid Ratings. Refer to Cool Roof Ratings Council (CRRC).
**Calculated using internal testing
• Coverage rate as reported assumes installation using side and en d lap recommendations .
www.soprema.us
310 Quadral Drive , Wadsworth, Ohio 44281
Toll Free: (800) 356-3521 I Tel: (330) 334-0066
0.87 0.90 27 234
initial 3 year initial 3 year
0.91 0.91 * 81 75
initial 3 year initial 3 year
0.89 N/A 6 N/A initial ** initial **
Reinforcement Non-woven polyester
Elastomeric bitumen Proprietaty blend of bitumen and SBS polymers
Top surfacing Ceramic coated granules
Back surfacing Polyolefin film
Selvage surface Polyolefin film
Selvage width, in (mm) 3 in (76 mm)
End lap, in (mm) 6 in (152 mm)
Thickness, mils (mm) 160 (4.0) ASTM D5147
Thickness @ selvage, mils (mm) 118 (3.0) ASTM 05147
Net mass per unit area, lb/100ft2 (g/m2) 110 (5371) ASTM D5147
Bottom coating thickness, mils {mm) ~ 40 (1.0) ASTM D5147
Peak load @ 0°F (-18°C), lbf/in (kN/m) 115(20.1) 90 (15.8) ASTrl/1 D5147
Elongation at peak load @ 0°F (-i 8°C), % 35 40 ASTM 05147
Peak load@ 73.4°F (23°C), lbf/in (kN/m) 85 (14.9) 65 (11 .4) ASTM D5147
Elongation at peak load@ 73.4°F (23°C), % 55 60 ASTM D5147
Ultimate elongation @ 73.4 °F (23°C), % 65 80 ASTM D5147
Tear strength@ 73.4°F (23°C), lbf (N) 125 (556) 85 (378) ASTM D5147
Low temperature flexibility, °F (0 C) -15 (-26) -15(-26) ASTM D5147
Dimensional stability, % <0.5 <0.5 ASTM D5147
Compound stability, °F (0 C) 240 (116) 240 (116) ASTM D5147
Granule embedment, g < 1.5 avg; 2.0 max SG ASTM D5147
Cyclic fatigue, condition 5 Pass ASHA D5849
* Data is represented by average values, unless noted otherwise.
PDS10003 -REV. 023419
JOB COPY
DESCRIPTION & FEATURES
SOPRAFIX Base 612 is an SBS-modified bitumen base ply for use in approved
multi-ply membrane and flashing assemblies and is designed specifically fo r
mechanical attac hment to approved substrates . SOPRAFIX Base 612 is composed
of a proprietary fo r mulat ion of elastome ric sty rene-butadiene-styrene (SBS) polymer
modified b itumen and is reinforced with a tough , dimensionally stable non-woven
polyester mat engineered for mechanical attachment. The tops ide and underside
are surfaced with polyolefin burn-off film to optimize heat welding .
STOFlAGE & HANDLING
Store rolls on end and maintain in an upright position to p revent damage . Store rolls in
a clean dry location and cover as necessary to protect rolls from environmental damage
such as extreme cold, heat, or moisture . Monitor varying environmental conditions du ring
storage , handling and application of SOPRAFIX Base 6 12 .
APPUCATION
Prior to installation, unroll SOPRAFIX Base 612 onto the roof surface and allow to relax.
Place SOPRAFIX Base 612 in desired position . SOPRAFIX Base 612 is mechanically
fastened through the 4 inch or 5 inch side laps using the 2 inch or 2 .4 inch plates
respec t ively following the details for the required uplift pressure. Subsequent approved
inter-ply or cap ply membranes are applied to SOPRAFIX Base 612 via heat welding .
Refer to the SOPREMA® SBS Roofing Manual for additional application guidelines .
MECHANICALLY
FASTENED
• Cove rage rat e as reported assumes install ation using side and end lap recommendation s . Cov erage reported refle cts
4 and 5 inch sid e laps respectively.
www.soprema.us
310 Quadral Drive, Wadsworth, Ohio 44281
To ll Free: (800) 356-3521 I Te l: (330) 334-0066
j
Reinforcement Non-woven polyester
Elastomeric bitumen Proprietary blend of bitumen and SBS polymers
Top surfacing Polyolefin film
Back surfacing Polyolefin film
Selvage width, in (mm) 4 (102) and 5 (127)
End lap, in (mm) 6 (152)
Thickness, mils (mm) 118 (3.0) ASTM D5147
Net mass per unit area, lb/100ft2 (g/m2) 76 (371i) ASTM D5147
Peak load @ 0°F (-18°C), lbf/in (kN/m) 115 (20.1) 90 (15.8) ASTM D5147
Elongation at peak load @ 0°F (-18°C), % 35 40 ASTM D5147
Peak load@ 73.4"F (23°C), lbf/in (kN/m) 85 (14.9) 65 (i 1.4) ASTM D5i47
Elongation at peak load@ 73.4°F (23°C), % 55 60 ASTM D5"147
Ultimate elongation@ 73.4°F (23°C), % 65 80 ASTM D5147
Tear strength @ 73.4°F (23°C), lbf (N) 125 (556) 85 (378) ASTM D5147
Low temperature flexibility, °F (0 C) -15(-26) -15(-26) ASTM D5147
Dimensional stability, % <0.5 < 0.5 ASTM D5147
Compound stability, °F ("C) 240 {116) 240 (116) ASTM D5147
* Data is represented by average values, unless noted otherwise.
FLORIDA BUILDING CODE
PDS10009 -REV. 020915
SAFETY DAT A SHEET
SBS MODIFIED BITUMEN WATERPROOFING MEMBRANE
Offerte en fram;ais
GHS PROTECTIVE CLOTHING TRANSPORT OF DANGEROUS GOODS
Not regulated Not regulated
SECTION I: IDENTIFICATION
Trade names:
Sopralene Stick, Sopralene Flam Stick, Sopralene 180 PS 2.2, Sopralene 180 Sanded 2.2, Colphene 180 Sanded, Colphene Stick, Soprafix Base 621, Soprafix Base 610,
Sopiafix Base 611, Sopiale11e 180 Sanded, Sopralene 180 PS 3.0, Sopralene Flam 180, Sopralene 180 SP 3.0, Sopralene SP 3.5, Colphenc Flam 180, Soprafix Base 613,
Soprafix Base 622, Soprafix Base 641, Soprafix Base 612, Colvent 180 SA, Colvent Flam 180 SA, Colvent 180 TG, Colvent Flam 180 TG, Sopralene Flam Antirock,
Soprafix Base 614, Sopralene 250 Sanded, Sopralene Flam 250, Sopralene 180 FR GR, Sopralene Flam 180 FR GR, Sopralene Flam 180 Ultra FR GR, Sopralene 180,
Colvent 180 FR GR, Sopralene Flam 250 FR+GR, Sopralene 250 FR GR, Sopralene Flam 250 FR GR, Sopralene Ultra FR GR, Sopralene Flam Ultra FR GR,
Sopralene 250 FR+ GR, Soprastar Flam, Soprastar Stick, Soprastar Sanded, Sopralast TV Alu, Sopralast TV Alu Sanded, Elastophene HS Sanded, Elastophene Flam
HS, Elastophene Flam HS FR, Elastophene HS FR Sanded, Elastophene HS FR GR (WHT), Elastophene Flam HS FR GR (WHT), M-SBase, M-Xpress, Sopra IV,
Sopra VI, Sopraflash, Sopraglass, Sopraseal, Soprawalk, Sopremium, Starter Stick GR, Stickson.
Membranes are used for all types of roofing needs, air barrier and waterproofing protection.
Manufacturers SOPREMA Canada
and distributors: 1675 Haggerty Street
Drummondville (Quebec) J2C 5P7
CANADA
Tel.: 819 478-8163
In case of emergency:
SOPREMA Inc.
44955 Yale Road West
Chilliwack (B.-C.) V2R 4H3
CANADA
Tel.: 604 793-7100
SOPREMA USA
310 Quadral Drive
Wadsworth (Ohio) 44281
UNITED ST ATES
Tel.: 1 800 356-3521
SOPREMA Gulfport
12251 Seaway Road
Gulfport (Mississippi) 39503
UNITED ST ATES
Tel.: 228 701-1900
SOPREMA (8:00am to 5:00pm): 1 800 567-1492 CANUTEC (Canada) (24h.): 613 996-6666 CHEMTREC (USA) (24h.): I 800 424-9300
SECTION II: HAZARD(S) IDENTIFICATION
Bitumen membrane. Asphalt odor. Under normal use, this product is not expected to create any health or environmental hazard. Inhalation of dust or of
asphalt fumes can cause a slight respiratory irritation and/or congestion.
SECTION III: COMPOSITION AND INFORMATION ON HAZARDOUS INGREDIENTS
NAME CAS# % WEIGHT EXPOSURE LIMIT (ACGIH)
TLV-TWA TLV-STEL
BITUMINOUS BLEND
Bitumen 8052-42-4 30-70 0.5 mglm3
Not established Asphalt fumes
Oxidized bitumen 1 64742-93-4 0-20 0.5 mglm 3
Not established Asphalt fumes
Self-adhesive membranes contain: 64742-52-5 0-30 Not established Not established Hh?:hly hydrotreated naphthenic oi1 1
Calcium Carbonate1 471-34-1 0-60 10 mglm3 Not established
Styrene butadiene copolymer1 9003-55-8 0-15 10 mglm3 Not established
FR products contain:
Calcium borate 1 1318-33-8 7-15 10 mglm3 Not established
FR Plus products contain:
Fire retardant1 Proprietary 1-5 2 mglm 3 Not established
REINFORCEMENT
Some products may contain fibre 2lass, polyester or a mix of 2lass 2rid and polyester.
Polyester mat 1 NIA 1-7 Not established Not established
l<'ibre glass mat1 NIA 1-7 Not established Not established
Contains: Fibre glass filament 1 65997-17-3 0,5-7 lf/cc Not established
SBS Modified Bitumen Waterproofing Membrane Revision date: April 30, 2015 Page 1 of 4
UNDERFACEANDSURFACE
Some membranes are protected by sand, talc, mineral granule, silicone paper, polyethylene or polypropylene film, aluminium, copper or
stainless steel foil.
Silicone paper NIA 6-20 Nol eslablished Not established
Polvoroovlene film NIA 2-10 Not established Not established
Polvethylene film 9002-88-4 2-10 Not established Not established
Aluminium, coooer or stainless steel foil NIA 4-15 Not established Not established
Sand NIA 7-13 0.1 mg/m3 Not established
Contains: Crystalline silica 2 14808-60-7 7-13 0.025 mg/m3 Not established
Talc 14807-96-6 7-13 Not established Not established
Coloured granules NIA 15-40 Not established Not established
Contains: Crystalline silica 2 14808-60-7 < 12 0.025 mg/m3 Not established
1. The exposure to the substance above the limits of exposure is not likely to occur considering its form (incorporated in the mixture) and/or the
provided use. The limit of exposure is given for reference only.
2. A proportion of crystalline silica can be present in the sand sprinkled on the top of some membranes. The crystalline silica contained in the sand
is not likely to be found in the ambient air in concentration above the limit of exposure since the sand adheres to the surface of the membrane.
SECTION UI: POTENTIAL HEALTH EFFECTS
Effects of short term (acute) exposure
SKIN CONT ACT
The product can cause a mechanical irritation of the skin because of its
rough surface. If the membrane is torch-applied, asphalt fumes can
cause skin irritation. The asphalt fumes can cause an irritation of the
skin. The contact with this product at high temperature can cause
thennal burns.
EYE CONTACT
The product is not likely to cause effects to the eyes. If the membrane is
torch-applied, asphalt fumes can be emitted of the product and cause
irritations, redness and conjunctivitis to the eyes. The contact with this
product at high temperature can cause thermal burns.
INHALATION
The product is not likely to cause effects on the respiratory system. If
the membrane is torch-applied, asphalt fumes can be emitted of the
product and cause irritations to the nose, the throat and the respiratory
tracts, tiredness, headaches, dizziness, nauseas and insomnia.
INGESTION
Exposure is not likely to occur by this route of entry under nonnal use
of the product.
Effects of long term (chronic) exposure
SKIN CONT ACT
The repeated or prolonged contact can cause irritation. If the membrane
is torch-applied, asphalt fumes can be emitted. The long-term exposure
to the asphalt fumes can cause changes of the pigmentation of the skin
which can be worsened by the exposure to the sun. (1)
INHALATION
If the membrane is torch-applied, asphalt fumes can be inhaled. No data
on chronic effects of the exposure to asphalt fumes on the lungs.
CARCINOGENICITY
Due to the product fonn, exposure to hazardous dusts or fumes is not
expected to occur. Information on carcinogenicity is given for reference
only. This product is not classifiable as a carcinogen.
Bitumen: According to the International Agency for Research on
Cancer (IARC): not classifiable as to its carcinogenicity to humans.
Epidemiological studies of roofers have generally demonstrated an
excess of lung cancer in these workers. However, it is unclear to what
extent these cancers may be attributable to asphalt exposures during
roofing operations, since in the past, roofers have been exposed to coal
tar and asbestos, which are known human lung carcinogens. Trace
amounts ofpolynuclear aromatic hydrocarbons (PAHs) may be present
in some asphalts and can be released upon excessive heating. Some of
these P AHs have been identified as having the potential to induce
carcinogenic and reproductive health effects. (2)
Oxidized bitumen: In its 2013 monograph (Volume 103), the
International Agency for Research on Cancer (IARC) conducted a
review of the potential carcinogenicity of bitumen (the European term
for asphalt). One of its conclusions was "occupational exposures to
oxidized bitumens and their emissions during roofing" are classified in
IARC Group 2A, "probably carcinogenic to humans." However, due to
the product form, exposure to such component is unlikely under normal
conditions ofuse. (2)
Crystalline Silica: Breathable crystalline silica from sand is not
expected to be released, sand is adhered to product. According to
IARC, crystalline silica is carcinogenic for human by inhalation. (3)
Fibreglass Filament: Fibreglass is not expected to be released. In
2001, IARC classified fibreglass as Group 3 "not classifiable as to its
carcinogenicity to humans". The American Conference of
Governmental Industrial Hygienists (ACGIH) and the National
Toxicology Program (NTP) classify the substance in Group 2B
(possibly carcinogenic to humans) based on studies in which animals
were injected with large quantities of fibreglass.
The other ingredients were not found to be carcinogenic or no
information is available on that matter.
TERATOGENICITY, EMBRIOTOXICITY, FETOTOXICITY
No infonnation available.
REPRODUCTIVE TOXICITY
No information available.
MUTAGEN! CITY
No information available.
TOXICOLOGICALLY SYNERGISTIC MATERIALS
No information available.
POTENTIAL ACCUMULATION
No information available.
SECTION IV: FIRST-AID MEASURES
SKIN CONT ACT
If there is presence of dust on the skin, wash gently with water and
soap. In the event of contact with the product melted, do not try to
remove the product of the affected area and rinse the area affected in
cold water. Obtain immediate medical attention. At the end of each
working day, clean all the parts of the body which came into contact
with asphalt fumes. Clean the clothing contaminated by the asphalt
fumes.
EYE CONTACT
SBS Modified Bitumen Waterproofing Membrane Revision date: April 30, 2015 Page2 of4
Flush eyes with water for at least 15 minutes while holding eyeiids
open. Do not attempt to remove material from affected area without
medical assistance. Obtain immediate medical attention.
INHALATION
Remove victim from contaminated place and restore breathing, if
required.
INGESTION
The ingestion of this product is not very likely to occur.
SECTION V: FIRE-FIGHTING MEASURES
FLAMMABILITY: Not applicable
EXPLOSION DAT A: Not applicable
FLASH POINT: Not applicable
AUTO-IGNITION TEMPERATURE: Not applicable
FLAMMABILITY LIMITS IN AIR:(% in volume) Not applicable
FIRE AND EXPLOSION HAZARDS
Asphalt fumes are flammable. Torch, used to weld waterproofing
membranes, can produce temperatures beyond 1100°C (2000°F). A void
all contact with materials sensitive to these temperatures, as lead or
plastic materials. Never work in an enclosed area where gas can
accumulate. Shield air conditioning units and other protrusions on the
roof with perlite panels or similar material when using the torch around
them. Never use torch (es):
-When substrate(s) have been recently covered by solvent-based
products (wait until it is dry).
-Near any combustible materials.
-Close to containers containing flammable liquids or materials (keep
open flame at least 3 m [1 O'] away).
-Directly on combustible substrate or insulation.
Voids, holes or gaps in substrate or located nearby the welding zone
can be protected against flame penetration. Particular precautions must
be taken to keep combustible or heat sensitive insulation away from the
torch flame. If wood fibre panels must be installed, use fireproof
panels. A void presence of combustible materials near open flame. At
all times and especially when leaving job site, make sure that there is
no smouldering or concealed fire. In that case, strictly follow the safety
measures. Job planning must allow for employee presence on the roof
at least one hour after torch application. At the end of every day, use a
heat detector gun to discover any unusually hot surface. Always have
one ABC fire extinguisher on hand, filled and in perfect working order
near each torch.
COMBUSTION PRODUCTS
Burning of this material will produce thick black smoke. Initating
and/or toxic gases including Hydrogen Sulphide and Sulphur Dioxide,
traces of metallic fumes may be generated by thermal decomposition or
combustion.
FIRE FIGHTING INSTRUCTIONS
Evacuate the area. Wear self-contained breathing apparatus and
appropriate protective clothing in accordance with standards. Approach
fire from upwind and fight fire from maximum distance or use
unmanned hose holders or monitor nozzles. Always stay away from the
containers at the time of the fire considering the high risk of explosion.
Move the rolls of membrane from fire area if it can be done without
risk. Cool the rolls of membrane with flooding quantities of water until
well after fire is out.
EXTINGUISHING MEDIA: Foam, CO 2, sand, chemical powder.
SECTION VI: ACCIDENTAL RELEASE 1\-IEASU
RELEASE OR SPILL
If hot material is spilled, allow enough time to cool completely and
remove to a container for disposal. Wear appropriate breathing
apparatus (if applicable) and protective clothing. Notify appropriate
environmental agencies. Wash spill area with soap and water. Dispose
of this material according to local environmental regulations.
SECTION VII: HANDLING AND STORAGE
HANDLING
SOPREMA's produt:ts must be applied by qualified applicators who
have received an adequate training, for the prevention and the
protection (in particular for the use of the extinguishers) against
accidents caused by use of combustible or flammable materials, of
liquefied propane gas, open flame, and their material of installation.
The present recommendations must be imperatively related to the
knowledge of the employees before the application of the products to
the building site. Check the construction and the composition of the
systems of roof and the walls before welding. Ensure of the cleanliness
of the places (debris).
Precautions of the use of the torch: Use only proper torching
equipment in perfect working order, C.S.A. certified. Never modify
torching equipment. Use only proper hoses suited for propane gas of
less than 15 m (50'). Verify and tighten all the connections before the
use of the equipment. Do not light the torch if a propane odor is
present. Never seek a leak with a flame. Use a torch whose gas output
is adjustable with stopping device. Follow the specifications, notices
and documentations of the manufacturers.
STORAGE
Flashings must be stored in such a way to prevent any creasing,
twisting, scratches and other damages of the roof. The materials must
be protected adequately and stored permanently away from flames or
welding sparks, protected from bad weather and any harmful
substances. Store self-adhesive membranes away from the sun.
SECTION VIU: EXPOSURE CONTROLS / PERSONAL
PROTECTION
HANDS: Wear resistant gloves.
RESP IRA TORY: If the TL V for dust is exceeded, if use is performed
in a poorly ventilated confined area, use an approved respirator in
accordance with standards.
EYES: Wear safety goggles in accordance with standards.
BODY: Wear adequate protective clothes. Do not wear synthetic
fabric. Remove clothing contaminated with solvents.
OTHERS: Eye bath and safety shower.
SECTION IX: PHYSICAL Al\1D CHEMICAL PROPERTIES
PHYSICAL STATE: Solid
ODOR AND APPEARANCE: Black membrane with asphalt odor
ODOR THRESHOLD: Not available
VAPOR PRESSURE (20°C): Not applicable
VAPOR DENSITY (air= 1 ): Not applicable
EVAPORATION RATE (Butyl acetate= 1): Not applicable
BOILING POINT (760 mm Hg): Not applicable
FREEZING POINT: Not applicable
SPECIFIC GRAVITY (1-JiO = 1): Variable
SOLUBILITY IN WATER (20°C): None
VOLATILE ORGANIC COMPOUND CONTENT (V.O.C):
Not measurable (0 g/L)
VISCOSITY: Not applicable
SECTION X: STABILITY AND REACTIVITY
ST ABILITY: This material is stable.
CONDITIONS OF REACTIVITY: Avoid excessive heat.
INCOMPATIBILITY: Acid and strong basis and organic solvents
and greasy substances.
HAZARDOUS DECOMPOSITION PRODUCTS: None identified.
HAZARDOUS POLYMERISATION: None.
SBS Modified Bitumen Waterproofing Membrane Revision date: April 30, 2015 Page3 o/4
SECTION XI: TOXICOLOGICAL INFORMATION
Effects of Short-Term (Acute) Exposure
No information available.
Effects of Long-Term (Chronic) Exposure
CARCINOGENICITY
Bitumen: Data from experimental studies in animals and cultured
mammalian cells indicate that laboratory-generated roofing asphalt
fume condensates are genotoxic and cause skin tumours. (2)
Crystalline Silica: Several studies have shown an increased incidence
of lung tumours in rats exposed to quartz by inhalation for up to 2
years. IARC has determined that there is sufficient evidence that quartz
is carcinogenic to experimental animals. (3)
The other ingredients were not found to be carcinogenic or no
information is available on that matter.
REPRODUCTIVE EFFECTS
No information available.
TERATOGENICITY, EMBRYOTOXICITY, FETOTOXICITY
No information available.
MUTAGENICITY
Crystalline Silica: None according to the available information.
No information available about the other ingredients.
SYNERGISTIC MATERIALS
Tobacco smoke increases the effects of silica dust on respiratory
system. Simultaneous exposure to known carcinogens as benzo (a),
pyrene, can increase the carcinogenicity of crystalline silica.
SECTION XII: ECOLOGICAL INFORMATION
ENVIRONMENT AL EFFECTS
No data.
BIODEGRADABILITY
This product is not biodegradable. No possible bioaccumulation and
unlikely bioconcentration in the food chain.
SECTION XIII: DISPOSAL CONSIDERATIONS
WASTE DISPOSAL
This product is not hazardous waste. Consult local, provincial, territory
or state authorities to know disposal methods. This material is not listed
by the EPA as hazardous waste according to the Resource Conservation
and Recovery Act (RCRA) of the United States. No Environmental
Protection Agency (EPA) waste numbers are applicable for this
product.
SECTION XIV: TRANSPORT INFORMATION
This product is not regulated by Department of Transportation (DOT)
and Transportation Dangerous Goods (TDG).
SECTION XV: REGULATORY INFORMATION
DSL:
TSCA:
Prop. 65:
All constituents of this product are included in the
Domestic Substances List (Canada).
All constituents of this product are listed on the Toxic
Substances Control Act Inventory (TSCA -United
States).
This product contains chemicals known to the State of
California to cause cancer or reproductive toxicity.
SECTION XVI: OTHER INFORMATION
GLOSSARY
ACGIH:
ANSI:
ASTM:
CAS:
CFR:
CSA:
DOT:
DSL:
EPA:
GHS
IARC:
LDsofLCso:
NFPA:
NIOSH:
NTP:
OSHA:
RCRA:
TDG:
TLV-TWA:
TSCA:
References:
American Conference of Governmental Industrial
Hygienists (United States)
American National Standards Institute (United States)
American Society for Testing and Materials (United
States)
Chemical Abstract Services
Code of Federal Regulations (United States)
Canadian Standardization Association
Department of Transportation (United States)
Domestic Substances List (Canada)
Environmental Protection Agency (United States)
Globally Harmonized System
International Agency for Research on Cancer
Less high lethal dose and lethal concentration published
National Fire Protection Association (United States)
National Institute for Occupational Safety and Health
(United States)
National Toxicology Program (United States)
Occupatfonal Safety & Health Administration (United
States)
Resource Conservation and Recovery Act (United
States)
Transportation of Dangerous Goods (Canada)
Threshold Limit Value -Time-Weighted Average
Toxic Substances Control Act (United States)
(1) Safety Data Sheet from the supplier
(2) WHO (2013) Bitumens and bitumen emissions, and some N-and
S-heterocyclic polycyclic aromatic hydrocarbons. Volume 103.
IARC monographs on the evaluation of carcinogenic risks to
humans.
(3) CHEMINFO (2015) Canadian Centre of Occupational Health and
Safety, Hamilton (Ontario) Canada
Code of SDS:
For information:
CA U DRU SS FS 044
1-800-356-3521 (U.S.A.)
I 800 567-1492 (Canada)
The Safety Data Sheets of SOPREMA are available on Internet at the
following site: www.soprema.us and www.soprema.ca
Update justification:
Oxidized bitumen added (sections II and III).
GHS Forn1at.
To the best of our knowledge, the information contained herein is accurate.
However, neither the above named supplier nor any of its subsidiaries
assumes any liability whatsoever for the accuracy or completeness of the
information contained herein. Final determination of suitability of any
material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain
hazards are described herein, we cannot guarantee that these are the only
hazards that exist.
SBS Modified Bitumen Waterproofing Membrane Revision date: April 30, 2015 Page4 of4
JOB COPY
Soprema #14 MP Fasteners -Package Quantities Below Order No. -See Below
I DESCRIPTION
Soprema #14 MP fastener is engineered to provide exceptional performance in a
variety of substrates and applications for Soprema Mechanically Fastened SBS
Membrane Systems.
Fasteners are designed for the attachment of insulation and membrane to steel (18-
22 ga.), wood, and structural concrete. To meet FM requirements, the fastener must
penetrate the steel deck three-quarter(¾") inch. Minimum penetration is one (1 ") inch
into wood, three-quarter(¾") inch through wood that is less than three-quarter(¾") inch
thick and one and one-quarter (1 ¼") inch into concrete. When installing in concrete,
pre-drill using a seven-thirty-second (7/32") inch drill bit and drill pilot hole one-half(½")
inch deeper than the required embedment. Install the fastener using a clutch-driven
drill motor with a maximum 1500 RPM.
The #14 MP Fastener offers these advantages:
• Superior pullout performance and ease of application
• Specific designed thread for increased back-out resistance
• FM Approvals, ICC/ES, Miami-Dade County, Florida State-Wide Approval
• Approved for steel, wood and concrete decks
• Soprema's flexibility to supply warranted fasteners based on the authorized
Soprema roofing applicator's preferred fastener request or applicator tools
used
• Used with Soprafix and UNILAY Mechanically Fastened Systems
lcoMP0s1T10N & PACKAGING
Soprema supplied #14 MP Fastener is case hardened carbon steel and use specific head, shank and thread diam-
eters, point types and head styles meeting FM Approvals corrosion and simulated wind uplift criteria requirements.
Fastener Size #14 MP Fastener Qty. I Pail** Part Number Fastener Size #14 MP Fastener Qty./ Pail** Part Number
1-1/4" F1011 1000 5" F1019 1000
1-1/2" F1012 1000 6" F1020 1000
2" F1013 1000 7" F1021 500
2-1/2" F1014 1000 8" F1022 500 -3" F1015 1000 9" F1023 250
3-1/2" F1016 1000 10" F1024 250
4" F1017 1000 12" F1025 250
4-1/2" F1018 1000 •• Each pail contains one (1) #3 Phillips Head drive bit
I WARRANTY
Soprema supplies Soprafix #14 MP Fasteners to authorized Soprema roofing applicators and are included in Soprema
Project Warranty Agreement offerings.
310 QUADRAL DRIVE • WADSWORTH, OHIO 44281 • TEL.: (330) 334-0066 • TOLL FREE: (800) 356-3521 • FAX: (330) 334-4289
General product information is provided on this Product Data Sheet. The physical property values reported here are based on testing conducted under controlled laboratory condttions according to accepted test standards.
JOB COPY .
PR ODUCT DATA S HEET
s
Soprema 2.4-lnch Seam plate -1000 / Pail
I DESCRIPTION
Soprafix Membrane 2.4-inch Seam Plates are engineered
to provide exceptional performance when used in specific
Soprafix or Unilay mechanically fastened SBS Roof
Assemblies. The Soprafix 2.4-inch seam plate has
engineered 'scoops' that allow the plate to get excellent grip
of the membrane without cutting into it with sharp barbs.
It is the installer's responsibility to know the Soprafix
system being installed, which Soprafix fastening
components are required, where and how often these
parts are placed within the System. Unless otherwise
noted in the Soprafix Approved Details, the installer must
center the required Soprafix Seam Plate down the middle
of the mechanically fastened side lap of the specified
Soprafix membrane. Soprema #15 or #14 Fasteners (or
other approved) are installed into the Soprafix Stress Plate
according to the applicable Fastening Pattern(s).
The 2.4-lnch Soprafix Seam Plate offers these advantages:
Labor savings with increased membrane rupture performance and
resistance (pull-over)
Included in Soprema Project Warranty Agreement offerings
Soprema's flexibility to supply warranted fasteners and stress plates
based on authorized Soprema roofing
applica_tor's preferred requests
See current FM Approvals, ICC/ES, Florida State Wide Product
Approval and Miami-Dade County Product
Approval for Approved Roof Assembly combinations
lcoMP0s1r10N & PACKAGING
Order No. F1059
Soprema supplied Soprafix Plates are manufactured from heavy gauge galvalume with special designed reinforcing
ribs. All Soprafix Plates meet building code and FM Approvals corrosion and simulated wind uplift criteria
requirements .
lwARRANTY
Soprema supplies Soprafix Stress Plates to authorized Soprema roofing applicators and are included in Soprema Project
Warranty Agreement offerings.
Increased Soprafix Stress Plate and fastener layout densities may be required for Wind Warranty Riders or when elevated
roof velocity pressures are encountered on specific projects.
310 QUADRAL DRIVE • WADSWORTH, OHIO 44281 • TEL.: (330) 334-0066 • TOLL FREE: (800) 356-3521 • FAX : (330) 334-4289
General product information is provided on this Product Data Sheet. The physical property values reported here are based on testing conducted under controlled laboratory condttions according to accepted test standards .
Sy
s
t
e
m
I
De
c
k
In
s
u
l
a
t
i
o
n
an
d
/
o
r
No
.
(N
o
t
e
1)
Th
e
r
m
a
l
Ba
r
r
i
e
r
Mi
n
.
22
ga
.,
ty
p
e
B,
Gr
a
d
e
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
S-
2
2
8
.
I
33
st
e
e
l
at
ma
x
.
6
ft
sp
a
n
s
mo
r
e
l
ay
e
r
s
,
an
y
at
t
a
c
h
e
d
6-
i
n
c
h
o
.c.
wi
t
h
TR
A
X
X
/
5
sc
r
e
w
s
co
m
b
i
n
a
t
i
o
n
I
Mi
n
.
22
ga
.,
ty
p
e
B,
Gr
a
d
e
Mi
n
.
1.
5
-in
c
h
,
On
e
or
S-
2
2
9
.
mo
r
e
la
y
e
r
s
,
an
y
80
st
e
e
l
co
m
b
i
n
a
t
i
o
n
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
5-
2
3
0
.
I
~~
n
.
22
1
ga
.
,
ty
p
e
B ,
Gr
a
d
e
I
mo
r
e
la
y
e
r
s
,
an
y
st
ee
co
m
b
i
n
a
t
i
o
n
Mi
n
.
22
ga
.
,
ty
p
e
B ,
5-
2
3
1
.
I
Gr
a
d
e
80
st
e
e
l
5-
2
3
2
.
I
Mi
n
.
22
ga
.,
ty
p
e
B,
Gr
a
d
e
80
st
e
e
l
5-
2
3
3
.
I
Mi
n
.
22
ga
.,
ty
p
e
B ,
Gr
a
d
e
80
st
e
e
l
5 -23
4
.
I
Mi
n
.
22
ga
.,
ty
p
e
B ,
Gr
a
d
e
80
st
e
e
l
5 -23
5
.
I
Mi
n
.
22
ga
.,
ty
p
e
B,
Gr
a
d
e
33
st
e
e
l
Mi
n
.
22
ga
.,
ty
p
e
B ,
5-
2
3
6
.
I
Gr
a
d
e
33
st
e
e
l
5-
2
3
7
.
I
Mi
n
.
22
ga
.,
ty
p
e
B,
Gr
a
d
e
33
st
e
e
l
Mi
n
.
22
ga
.,
ty
p
e
B ,
S-
2
3
8
.
I
Gr
a
d
e
80
st
e
e
l
NE
M
O
ET
C
,
LL
C
Ce
r
t
i
f
i
c
a
t
e
of
Au
t
h
o
r
i
z
a
t
i
o
n
#3
2
4
5
5
Pr
e
p
a
r
e
d
by
:
Ro
b
e
r
t
Ni
e
m
i
n
e
n
,
PE
-59
1
6
6
1
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
na
t
i
o
n
1
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
1
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
1
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
1
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
o r
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
1
Mi
n
.
1.
5
-in
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
1
Mi
n
.
1 .5-
i
n
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
1
Mi
n
.
1.
5
-
i
n
c
h
,
On
e
or
mo
r
e
la
y
e
r
s
,
an
y
co
m
b
i
n
a
t
i
o
n
JO
B
CO
P
Y
RE
R
O
O
F
(T
E
A
R
-
O
F
F
)
OR
RE
C
O
V
E
R
HE
D
SO
P
R
A
F
I
X
,
BO
N
D
E
D
RO
O
F
CO
V
E
R
Ba
s
e
M
e
m
br
a
n
e
Ba
s
e
Fa
s
t
e
n
e
r
s
S pa
c
i
n
g
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2.
4
in
.
SO
P
R
A
F
I
X
Ba
s
e
61
0
,
61
1
,
61
2
,
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
5
HD
12
-
i
n
c
h
o .c
.
wi
t
h
i
n
4-
i
n
c
h
61
4
or
62
2
w
i de
,
he
a
t
-
w
e
l
d
e
d
la
p
s
wi
t
h
So
p
r
e
m
a
2.
4
"
Se
a
m
Pl
a
t
e
SO
P
R
A
F
I
X
Ba
s
e
61
0
,
61
1
,
6
1
2
,
Tr
u
f
a
s
t
#1
4
HD
wi
t
h
Tr
u
f
a
s
t
2.
4
i
n.
12
-
i
n
c
h
o.
c
.
wi
t
h
i
n
4-
i
n
c
h
61
4
or
62
2
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
4
MP
wi
d
e
,
he
a
t
-we
l
d
e
d
la
p
s
wi
t
h
So
p
r
e
m
a
2.
4
"
Se
a
m
Pl
a
t
e
SO
P
R
A
F
I
X
Ba
s
e
61
0
,
61
1
,
61
2
,
Tr
u
f
a
s
t
#1
4
HD
wi
t
h
Tr
u
f
a
s
t
2.
4
in
.
12
-
i
n
c
h
o.
c
.
wi
t
h
i
n
4-
i
n
c
h
61
4
or
62
2
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
4
MP
wi
d
e
,
he
a
t
-
w
e
l
d
e
d
la
p
s
wi
t
h
So
p
r
e
m
a
2.
4
"
S
e
a
m
Pl
a
t
e
So
p
r
e
m
a
#1
5
EL
wi
t
h
SO
P
R
A
F
I
X
2
3/
8
I1
2
-
i
n
c
h
o.
c
.
wi
t
h
i
n
5-
i
n
c
h
Un
i
l
a
y
in
.
SB
St
r
e
s
s
Pl
a
t
e
s
wi
d
e
he
a
t
-
w
e
l
d
e
d
la
p
s
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2.
4
in
.
12
-
i
n
c
h
o .c.
wi
t
h
i
n
4 -in
c
h
SO
P
R
A
F
I
X
Ba
s
e
62
1
or
62
2
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
5
HD
wi
t
h
So
p
r
e
m
a
2.
4
"
Se
a
m
Pl
a
t
e
wi
d
e
,
he
a
t
-
w
e
l
d
e
d
la
p
s
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2.
4
in
.
12
-
i
n
c
h
o.
c
.
wi
t
h
i
n
4-
i
n
c
h
SO
P
R
A
F
I
X
Ba
s
e
61
4
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
5
HD
wi
d
e
,
he
a
t
-
w
e
l
d
e
d
l ap
s
wi
t
h
So
p
r
e
m
a
2 .4"
Se
a
m
Pl
a
t
e
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2.
4
in
.
12
-
i
n
c
h
o .c.
wi
t
h
i
n
4-
i
n
c
h
SO
P
R
A
F
I
X
Ba
s
e
61
4
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
5
HD
wi
t
h
So
p
r
e
m
a
2 .4"
Se
a
m
Pl
a
t
e
wi
d
e
,
he
a
t
-
w
e
l
d
e
d
la
p
s
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2
in
.
I
SO
P
R
A
F
I
X
Ba
s
e
62
1
o,
62
2
I
Ba
,
b
e
d
Me
t
a
l
Se
a
m
Pl
a
t
e
s
o,
T,
u
f
a
s
t
6-
i
n
c
h
o.
c
.
wi
t
h
i
n
4-
i
n
c
h
wi
d
e
,
2.
4
in
.
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
#1
5
HD
wi
t
h
So
p
r
e
m
a
2 "
Se
a
m
Pl
a
t
e
or
he
a
t
-
w
e
l
d
e
d
la
p
s
So
p
r
e
m
a
2.
4
"
Se
a
m
Pl
a
t
e
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2
in
.
I
SO
P
R
A
F
I
X
Ba
s
e
61
0
,
6
1
1
,
6
1
2
,
I
Ba
<
b
e
d
Me
t
a
l
Se
a
m
Pl
a
t
e
s
o,
T,
u
f
a
s
t
1
6
.
h
.
h
.
h
.d
.
-m
e
o .c.
wi
t
In
4-
i
n
c
wI
e ,
61
4
or
62
2
2.
4
in
.
Sc
~
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
he
a
t
-
w
e
l
d
e
d
la
s
#1
5
HD
wi
t
h
So
p
r
e
m
a
2"
Se
a
m
Pl
a
t
e
or
p
So
p
r
e
m
a
2.
4
"
Se
a
m
Pl
a
t
e
Tr
u
f
a
s
t
#1
5
EH
D
wi
t
h
Tr
u
f
a
s
t
2
in
.
I
SO
P
R
A
F
I
X
Ba
s
e
61
0
,
61
1
,
61
2
,
I
Ba
<
b
e
d
Me
t
a
l
Se
a
m
Pl
a
t
e
s
o,
T,
u
f
a
s
t
6-
i
n
c
h
o .c
.
wi
t
h
i
n
4-
i
n
c
h
wi
d
e
,
2.
4
in
.
Sc
o
o
p
Se
a
m
Pl
a
t
e
s
or
So
p
r
e
m
a
61
4
or
62
2
#1
5
HD
wi
t
h
So
p
r
e
m
a
2"
Se
a
m
Pl
a
t
e
o r
he
a
t
-
w
e
l
d
e
d
la
p
s
So
p
r
e
m
a
2.
4
"
Se
a
m
Pl
a
t
e
I
SO
P
R
A
F
I
X
Ba
s
e
62
1
o
,
62
2
Tr
u
f
a
s
t
#1
4
HD
or
#1
5
EH
D
wi
t
h
I
T,
u
f
a
s
t
2
;n
.
Ba
,
b
e
d
Me
t
a
l
Se
a
m
Pl
a
t
e
s
6-
i
n
c
h
o .c.
wi
t
h
i
n
4-
i
n
c
h
wi
d
e
,
or
So
p
r
e
m
a
#1
4
or
#1
5
HD
wi
t
h
he
a
t
-
w
e
l
d
e
d
la
p
s
So
p
r
e
m
a
2"
Se
a
m
Pl
a
t
e
5T
H
ED
I
T
I
O
N
(2
0
1
7
)
FB
C
NO
N
-
H
V
H
Z
EV
A
L
U
A
T
I
O
N
So
p
r
e
m
a
Mo
d
i
f
i
e
d
Bi
t
u
m
e
n
Ro
o
f
Sy
s
t
e
m
s
;
(8
0
0
)
35
6
-
3
5
2
1
8NEMOletc. Roof Cover (Note 15) I MDP Ply I Cap I (psf)
I
(O
p
t
i
o
n
a
l
)
SBS-TA-F I SBS-TA-F I -75 .0
El
a
s
t
o
p
h
e
n
e
SP or SP 3 .0
or
Sopralene 180 SP o r I SBS-CAl I -75 .0
18
0
S P 3.5 , torch-applied
(O
p
t
i
o
n
a
l
)
SBS-TA-F I SBS-TA-F I -75.0
I
None I None I -82.5
I
None I SBS-CAl I -97.5
El
a
s
t
o
p
h
e
n
e
SP or SP 3 .0
or
Sopralene 180 SP or I SBS-CAl I -97.5
18
0
SP 3.5, torch-applied
(O
p
t
i
o
n
a
l
)
SBS-TA-F I SBS-TA-F I -97.5
I
None I SBS-CAl I -112 .5
I
El
a
s
t
o
p
h
e
n
e
SP o, SP 3 .0
or
Sopralene 180 SP or I SBS-CAl I -112 .s
18
0
SP 3 .5 , torch-applied
I
(O
p
t
i
o
n
a
l
)
SBS-TA-F I SBS-TA -F I -112.5
I
None I SBS-CAl I -120.0
Ev
a
l
u
a
t
i
o
n
Report S35000 .12 .10-R25 for FL3915-R27 Revision 25 : 02/12/2019 Appendix 1 , Page 53 of 117
FLASHING CAP SHEET
POLYESTER REINFORCED FLASHING BASE PLY
FASTENER
BASE SHEET/ANCHOR SHEET
COVERBOARD
INSULATION
INSULATION BASE SHEET/ANCHOR SHEET
THERMAL BARRIER VAPOR RETARDER/AIR BARRIER
ASSEMBLY
NOTES:
1. SOP REMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS} AND SAFETY DATA SHEETS (SOS} FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERT A RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
SOPREMA®
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE: 2 PLY SBS MEMBRANE,
INSULATED,
ROOF ASSEMBLY
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 10.26.2017 DRAWING NUMBER:
SCALE: NTS US.RSBS.01.01
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
BASE SHEET/ANCHOR SHEET/BACKER PLY
CURB
VAPOR RETARDER/AIR BARRIER/BACKER PLY
NON-REMOVABLE CURB COUNTERFLASHING
SHEET METAL COUNTERFLASHING
FLASHING CAP SHEET
POLYESTER REINFORCED FLASHING BASE
COVERBOARD
INSULATION
INSULATION VAPOR RETARDER/AIR BARRIER
INSULATION DA3[ 81 l[[T/ANCI IOR 81 l[[T
NOTES:
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA GERTA RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS
4. FLASHING PLIES MUST EXTEND VERTICALLY A MINIMUM OF 8' FROM ROOF SURFACE. FLASHING PLIES EXTENDING VERTICALLY MORE THAN 24' FROM ROOF SURFACE MUST BE ADHERED AND
MECHANICALLY FASTENED ALONG THE TOP LEADING EDGE. REFER TO PUBLISHED DOCUMENTATION.
5. FOR 90° TRANSITIONS, FLASHING PLIES MUST MEET THE FOLLOWING REQUIREMENTS: HEAT WELD POLYESTER REINFORCED FLASHING BASE PLIES. HEAT WELD POLYESTER REINFORCED
GRANULE FLASHING CAP SHEET, OR HEAT WELD FOIUFILM CLAD FLASHING CAP SHEET.
SOPREMA
US CORPORATE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
~
PROJECT:
TITLE: 2 PLY SBS MEMBRANE, INSULATED
CURB WITH NON-REMOVABLE
COUNTERFLASHING
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION:
DATE: 7.9.2015 DRAWING NUMBER:
SCALE: NTS US.RSBS.05.01
DATE:
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
TERMINATION BAR
FASTEN AT 8' O.C. MAXIMUM
ALONG HORIZONTAL EDGE
VAPOR RETARDER/AIR BARRIER/
BASE SHEET/ANCHOR SHEET/
EXTEND FLASHING
MINIMUM OFl3X~t•mill"
MINIMUM OF 3' BEYOND FA
EXTEND FLASHING CAP SHEET A
MINIMUM OF 1' eey1\¾@Jfj_L,@rll4&1fi:@:qli~
MINIMUM OF 1' BEYOND FLASHING BASE PLY
COVERBOARD
SOPRAMASTIC SP1
BASE SHEET/ANCHOR SHEET
NOTES:
COUNTERFLASHING
FLASHING CAP SHEET
POLYESTER REINFORCED FLASHING BASE PLY
BASE PLY
BASE SHEET/ANCHOR SHEET
\_ VAPOR RETARDER/AIR BARRIER
CAP SHEET
THERMAL BARRIER
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERT A RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS
4. FLASHING PLIES MUST EXTEND VERTICALLY A MINIMUM OF 8' FROM ROOF SURFACE. FLASHING PLIES EXTENDING VERTICALLY MORE THAN 24" FROM ROOF SURFACE MUST BE ADHERED AND
MECHANICALLY FASTENED ALONG THE TOP LEADING EDGE. REFER TO PUBLISHED DOCUMENTATION.
5. FOR 90° TRANSITIONS, FLASHING PLIES MUST MEET THE FOLLOWING REQUIREMENTS: HEAT WELD POLYESTER REINFORCED FLASHING BASE PLIES. HEAT WELD POLYESTER REINFORCED
GRANULE FLASHING CAP SHEET, OR HEAT WELD FOIUFILM CLAD FLASHING CAP SHEET.
Ill)
SOPREMA
US CORPORATE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE: 2 PLY SBS MEMBRANE, INSULATED
WALL FLASHING WITH
SURFACE MOUNTED COUNFERFLASHING
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION:
DATE: 7.14.2015 DRAWING NUMBER:
SCALE: NTS US.RSBS.04.03
DATE:
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
CLEAN AND PREPARE PENETRATION SURFACE
CAP SHEET
POL VESTER REINFORCED FLASHING
NOTES:
EXTEND FLASHING BASE PLY A MINIMUM
OF 3" BEYOND FASTENER PLATES
BASE SHEET/ANCHOR SHEET
BASE SHEET/ANCHOR SHEET
VAPOR RETARDER/AIR BARRIER
THERMAL BARRIER
EXTEND REINFORCING FABRIC A MINIMUM
OF 4" BEYOND THE ROOF SURFACE
EXTEND REINFORCING FABRIC A MINIMUM
OF 8" BEYOND THE PENETRATION
REINFORCING FA □RIC
INSULATION
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SOS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERT A RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
4. SOPREMA RECOMMENDS 8 INCH VERTICAL FLASHING HEIGHTS. FLASHING DETAILS SHOWN INCLUDE MINIMUM DIMENSIONS TO MEET WARRANTY REQUIREMENTS. CONTACT SOPREMA FOR
ADDITIONAL REQUIREMENTS.
5. DO NOT APPLY ALSAN RS LIQUID APPLIED SIYSTEMS OVER SBS MODIFIED BITUMEN MATERIALS ADHERED USING COLPLY OR COLPL Y MODIFIED ADHESIVES OR CEMENTS. SELF ADHERE, HOT AIR
WELD OR TORCH APPLY THE SBS MODIFIED BITUMEN MEMBRANE AND FLASHINGS IN ALL AREAS WHERE ALSAN RS WILL BE APPLIED.
Q;)
SOPREMA
US CORPORATE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE: 2 PLY SBS MEMBRANE,
INSULATED,
PENETRATION WITH LIQUID FLASHING
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 4.18.2016 DRAWING NUMBER:
SCALE: NTS US.RSBS.06.03
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOP REMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
CLEAN AND PREPARE PENETRATIONS
AS REQUIRED
SOPREMA PITCH POCKET
FILLERAT2"THICK~
NON-SHRINK GROUT
MINIMUM 4" FLANGE PRIMED ON BOTH SIDES,
METAL FLANGE SET IN A FULL BED
OF SOPRAMASTIC SBS MASTIC.
INSULATION
INSULATION
INSULATION
NOTES:
DECK
PENETRATION POCKET MINIMUM 4" HIGH,
SOLDER/WELD ALL SEAMS
POLYESTER REINFORCED FLASHING BASE PLY
INSTALL FASTENER PLATE A MINIMUM OF
1~,~~~ii~~:NGE
EXTEND FLASHING BASE PLY A MINIMUM
OF 3" BE'YONn FASTFNFR Pl ATF
BASE PLY
BASE SHEET/ANCHOR SHEET
VAPOR RETARDER/AIR BARRIER
BASE SHEET/ANCHOR SHEET
THERMAL BARRIER
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SOS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERT A RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
SOPREMA®
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE:
2 PLY SBS MEMBRANE, INSULATED
PENETRATION POCKET
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 5.11.2015 DRAWING NUMBER:
SCALE: NTS US.RSBS.06.02
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
EXTENB~AnLJMll,j{IR/li,//MAANIMUM
OEllF/4' BEYOND REINFORCING FABRIC
CLEAN AND PREPARE PENETRATION SURFACE
INSTALL FASTENER PLATE
AROUND PENETRATION SPACED
A MAXIMUM OF 12' APART
NOTES:
EXTEND FLASHING BASE PLY
A MINIMUM OF 3' BEYOND
FASTENER PLATES
BASE SHEET/ANCHOR SHEET
BASE SHEET/ANCHOR SHEET
VAPOR RETARDER/AIR BARRIER
EXTEND REINFORCING FABRIC A MINIMUM
OF 4" BEYOND THE ROOF SURFACE
EXTEND REINFORCING FABRIC FINGERS A MINIMUM
OF 2" BEYOND THE PENETRATION
EXTEND REINFORCING FABRIC A MINIMUM
OF 8' BEYOND THE PENETRATION
EXTEND ALSAN ~MN()MI.M.INIMUM
OF 1143131'3'.'MilDIREfilFJB~(S~C
COVERBOARD
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA GERTA RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
4. SOPREMA RECOMMENDS 8 INCH VERTICAL FLASHING HEIGHTS. FLASHING DETAILS SHOWN INCLUDE MINIMUM DIMENSIONS TO MEET WARRANTY REQUIREMENTS. CONTACT SOPREMA FOR
ADDITIONAL REQUIREMENTS.
5. DO NOT APPLY ALSAN RS LIQUID APPLIED SIYSTEMS OVER SBS MODIFIED BITUMEN MATERIALS ADHERED USING COLPLY OR COLPL Y MODIFIED ADHESIVES OR CEMENTS. SELF ADHERE, HOT AIR
WELD OR TORCH APPLY THE SBS MODIFIED BITUMEN MEMBRANE AND FLASHINGS IN ALL AREAS WHERE ALSAN RS WILL BE APPLIED.
SOPREMA~
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE: 2 PLY SBS MEMBRANE,
INSULATED,
PLUMBING VENT WITH LIQUID FLASHING
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 4.18.2016 DRAWING NUMBER:
SCALE: NTS US.RSBS.06.01 b
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
PLUMBING VENT
BASE SHEET/ANCHOR SHEET
BASE SHEET/ANCHOR SHEET
VAPOR RETARDER/AIR BARRIER
NOTES:
SOFT METAL PIPE FLASHING
MINIMUM 4" FLANGE PRIMED ON BOTH SIDES, METAL FLANGE
SET IN A FULL BED OF SOPRAMASTIC SBS MASTIC
CAP SHEET
POLYESTER REINFORCED FLASHING BASE PLY
FASTEN BASE PLY AROUND PIPE
~k-1:~N~R~sAl~~~ff ~lv'lfMMUM
OF 3" B~nIft,t,.~~l~~t~~~ MINIMUM
OF 3" BEYOND FASTENER PLATE
COVERBOARD
INSULATION
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERT A RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
SOPREMA®
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE:
2 PLY SBS MEMBRANE, INSULATED
PLUMBING VENT W/ SOFT METAL FLASHING
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 5.11.2015 DRAWING NUMBER:
SCALE: NTS US.RSBS.06.01 a
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
NOTES:
MITER CUT FLASHI
BASE PLY AS SHOW
EXTEND FLASHING CAP SHEET A MINIMUM
8RlI:llmlBl.lNEH1HS COOBBe[lFA"M\SININ9 DETAIL
OF 3" AROUND THE CORNER OF FLASHING DETAIL
l~~~~@ts~
FLASHING
BASE PLY
EXTEND FLASHING CAP SHEET
A MINIMUM OF 1' BEYOND
~llm!.l',lf«t\~~l~LY
A MINIMUM OF 1' BEYOND
-CAP ~~@Ef l YING Fl ASHING RASF Pl Y
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SOS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERTA RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
SOPREMA®
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE:
2 PLY SBS MEMBRANE
INSIDE CORNERS
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 3.14.2016 DRAWING NUMBER:
SCALE: NTS US.RSBS.02.04
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
FLASHING BASE PLY
STEP 1
FLASHING BASE PLY
NOTES:
EXTEND FLASHING BASE PLY A MINIMUM
fl:F~~@~Erf0'f:f!~~oETA1L
OF 3" AROUND THE CORNER OF FLASHING DETAIL
TERMINATE FLASHING BASE PLY
A\~2~~JfT~m~~m~i~~l~ty-
AT CORNER OVi™lc!tJri!l~~ING
MITE~r~~
FLASHING CAP SHEET
EXTEND FLASHING CAP SHEET A MINIMUM
8fx't1MrH--Llj,_~~ttJG~r ~~~ETAIL
FLl?fHrN~~RWfil-i~~T CORNER OF FLASHING DETAIL
CAP SHEET
BASE PLY
FLASHING BASE PLY
FLASHING BASE PLY
1. SOPREMA DETAIL DRAWINGS: REFER TO SOP REMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SOS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERTA RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
SOPREMA
US CORPORATE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
<8J
PROJECT:
TITLE:
2 PLY SBS MEMBRANE
OUTSIDE CORNERS
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 3.16.2016 DRAWING NUMBER:
SCALE: NTS US.RSBS.02.03
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
ROOF EDGE SYSTEM
WEATHERPROOF MEMBRANE
BASE SHEET/ANCHOR SHEET/
CANT
EXTEND FLASHING
MINIMUM OFi3l<iB~~ljfij!)W
MINIMUM OF 3" BEYOND FA
EXTEND FLASHING CAP SHEET A
MINIMUM OF 1" eeyl3¾1§)ifi.~~~qlt~
MINIMUM OF 1" BEYOND FLASHING BASE PLY
COVERBOARD
BASE SHEET/ANCHOR SHEET
,,-VAPOR RETARDER/AIR BARRIER/BACKER PLY
FLASHING CAP SHEET
POLYESTER REINFORCED FLASHING BASE PLY
BASE PLY
CAP SHEET
THERMAL BARRIER
BASE SHEET/ANCHOR SHEET
VAPOR RETARDER/AIR BARRIER
NOTES:
1. SOPREMA DETAIL DRAWINGS: REFER TO SOPREMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SDS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA CERTA RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS
4. FLASHING PLIES MUST EXTEND VERTICALLY A MINIMUM OF 8" FROM ROOF SURFACE. FLASHING PLIES EXTENDING VERTICALLY MORE THAN 24" FROM ROOF SURFACE MUST BE ADHERED AND
MECHANICALLY FASTENED ALONG THE TOP LEADING EDGE. REFER TO PUBLISHED DOCUMENTATION.
5. FOR 90° TRANSITIONS, FLASHING PLIES MUST MEET THE FOLLOWING REQUIREMENTS: HEAT WELD POLYESTER REINFORCED FLASHING BASE PLIES. HEAT WELD POLYESTER REINFORCED
GRANULE FLASHING CAP SHEET, OR HEAT WELD FOIUFILM CLAD FLASHING CAP SHEET.
SOPREMA®
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE:
2 PLY SBS MEMBRANE, INSULATED
PARAPET WALL WITH METAL COPING
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION:
DATE: 7.8.2015 DRAWING NUMBER:
SCALE: NTS US.RSBS.03.04
DATE:
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.
CAP SHEET
POLYESTER REINFORCED FLASHING BASE PLY
SOPRAMASTIC SP1
ROOF EDGE SYSTEM
MINIMUM 4' FLANGE PRIMED ON BOTH SIDES,
METAL FLANGE SET IN A FULL BED OF
SOPRMASTIC SBS MASTIC
VAPOR RETARDER/AIR BARRIER
BASE SHEET/ANCHOR SHEET
NOTES:
DECK
EXTEND FLASHING BASE PLY A MINIMUM
OF 3" BEYOND MET AL FLANGE
BASE PLY
BASE SHEET/ANCHOR SHEET
COVERBOARD
THERMAL BARRIER
1. SOP REMA DETAIL DRAWINGS: REFER TO SOP REMA AND OTHER RELATED PUBLISHED DOCUMENTATION, PRODUCT DATA SHEETS (PDS) AND SAFETY DATA SHEETS (SOS) FOR ADDITIONAL
INFORMATION. ALL DETAIL DRAWINGS AND RELATED INSTALLATION GUIDELINES ARE PROVIDED BY SOPREMA FOR THE SOLE PURPOSE OF ISSUING A SOPREMA WARRANTY. ACCORDINGLY, THE
DETAIL DRAWINGS ARE NOT OFFERED, AND SHOULD NOT BE CONSIDERED, AS A SUBSTITUTE FOR PROFESSIONAL DESIGN SERVICES.
2. HOT WORK: THE CONTRACTOR IS RESPONSIBLE FOR DETERMINING APPROPRIATE CONDITIONS TO UTILIZE HEAT-WELDING EQUIPMENT. REFER TO THE NRCA GERTA RECOMMENDATIONS, LOCAL
CODES AND BUILDING OWNER'S REQUIREMENTS FOR HOT WORK OPERATIONS.
3. PRIMER: WHERE NOT SHOWN OR INDICATED ON DETAIL DRAWINGS, REFER TO MATERIAL PRODUCT DATA SHEETS FOR PRIMER APPLICATION REQUIREMENTS.
SOPREMA®
US CORPORA TE ADDRESS
310 QUADRAL DRIVE
WADSWORTH, OHIO 44281
www.soprema.us
Tel:330.334.0066
PROJECT:
TITLE:
2 PLY SBS MEMBRANE, INSULATED
DRIP EDGE
DRAWN BY: SOPREMA TECHNICAL SUPPORT, GGALLOWAY
NO.: REVISION: DATE:
DATE: 4.23.2015 DRAWING NUMBER:
SCALE: NTS US.RSBS.03.02
USAGE OF THIS DETAIL IS GOVERNED BY THE TERMS OF SERVICE FOR SOPREMA DETAILS.
PLEASE CONSULT THESE TERMS OF SERVICE PRIOR TO UTILIZING THIS DRAWING.