345 BELVEDERE ST RESA21-0024 FL5179_R32_II_IN0234 41-18 SL_2x REV 12-14-21_1MODEL DESIGNATION:
MAXIMUM OVERALL NOMINAL SIZE: Single up to 73" x 63"
DESIGN PRESSURE RATING: Positive: 30.0 PSF
Simonton Horizontal Slider Series
USABLE CONFIGURATIONS:
GENERAL DESCRIPTION:
2"
MAX.
Negative: 30.0 PSF
OX or X0
41-18 Vinyl Window
The head, sill, and side jambs are extruded PVC. The wall thickness
through which the anchor screw penetrates is a minimum of 0.070".
r9" 0.C.
MAX. TYP.
2"
MAX.~ —+
63" MAX. OVERALL FRAME HEIGHT
I
I
1
\
\
L
CD
0
X
1
O
_J
}
<
X
<
73" MAX. OVERALL FRAME WIDTH
}
#6 X 1 1/4" MIN. WOOD
SCREW WITH 1.00" MIN.
EMBEDMENT INTO WOOD
MIN. EDGE DIST., SEE NOTES
SILICONE CAULK
SILICONE CAULK
NO P.E. SEAL REQUIRED
INSTALLATION SUPPORTED
BY AAMA TEST REPORTS
OHEAD
1
1/4" MAX. SHIM
2X BUCK
#6 X 1 1/4" MIN. WOOD
SCREW WITH 1.00" MIN.
EMBEDMENT INTO WOOD
MIN. EDGE DIST., SEE NOTES
OSILL
2
2X BUCK
1/4" MAX. SHIM
REV.
#:
REVISIONS:
REVISED BY:
DATE:
9
UPDATED PER NEW TESTING.
T.D.D.
10/09/12
10
UPDATED SIZE PER NEW TESTING.
T.D.D.
02/20/13
11
ADDED MIN. EDGE DIST. NOTE.
T.D.D.
02/20/13
12
ADDED NOTES 11 & 12.
LMH
07/07/16
13
UPDATED TO 7TH EDITION (2020) FBC
LMH
02/15/21
#6 X 1 1/4" MIN. WOOD
SCREW WITH 1.00" MIN.
EMBEDMENT INTO WOOD
MIN. EDGE DIST., SEE NOTES
2X BUCK
1/4" MAX. SHIM
SILICONE CAULK
CD,
JAMB
NOTES
I. THIS INSTALLATION HAS BEEN EVALUATED FOR USE IN LOCATIONS ADHERING TO THE TEXAS & FLORIDA BUILDING CODE AND WHERE
PRESSURE REQUIREMENTS AS DETERMINED BY ASCE 7 MINIMUM DESIGN LOADS FOR BUILDINGS AND OTHER STRUCTURES DO NOT
EXCEED THE DESIGN PRESSURE RATINGS HEREIN, FOR USE OUTSIDE THE H.V.H.Z.
2. ALL INTERIOR AND EXTERIOR PERIMETER SURFACES OF THE WINDOW MUST BE CAULKED.
3. ANCHORS SHALL BE SPECIFIED AND SPACED AS SHOWN ANCHOR EMBEDMENT TO BASE MATERIAL SHALL BE BEYOND WALL DRESSING OR
STUCCO AND INTO WOOD.
4. THE RESPONSIBILITY FOR SELECTION OF SIMONTON PRODUCTS TO MEET ANY APPLICABLE LOCAL LAWS, BUILDING CODES, ORDINANCES,
OR OTHER SAFETY REQUIREMENTS RESTS SOLELY WITH THE ARCHITECT, BUILDING OWNER, OR CONTRACTOR.
5. SHIMS ARE OPTIONAL. MAXIMUM SHIM STACK IS 1/4".
6. WOOD BUCKS (BY OTHERS) MUST BE ENGINEERED AND ANCHORED PROPERLY TO TRANSFER LOADS TO THE STRUCTURE. WOOD BUCKS
SHALL BE SPRUCE -PINE -FIR. WOOD MINIMUM SPECIFIC GRAVITY = 0.42 PSI.
7. WHEN USED IN AREAS REQUIRING IMPACT PROTECTION, THIS PRODUCT REQUIRES THE USE OF APPROVED IMPACT RESISTANT SHUTTERS
OR OTHER EXTERNAL PROTECTION.
8. FLASHING SHOULD BE APPLIED USING THE ASTM E 2112 METHOD APPROPRIATE FOR THE OPENING INTO WHICH THE WINDOW IS BEING
INSTALLED.
9. INSTALLATION SCREWS MUST BE AT LEAST 1/2" FROM THE EDGE OF THE WOOD.
10. THIS PRODUCT COMPLIES WITH ASTM E 1300.
II. USE A BACKER ROD ON ALL JOINTS >3/4" DEEP AND/OR WIDER THAN 1/4". FINISHED CAULK JOINT SHOULD BE A MINIMUM OF 3/8"
DEEP.
DISCLOSURE STATEMENT
This document is the property of Simonton Windows, which
retains all proprietary and other rights to its subject matter.
This document is provided to the recipient on the expressed
condition that it is not to be disclosed, reproduced in whole or
part, nor used in conjunction with the design, manufacture or
repair of goods for anyone other than Simonton Windows
without its consent. This restriction does not limit the
recipient's rights to utilize information contained in this
document which is properly obtained from another source
MATERIAL:
RMS FINISH:
EXCEPT AS NOTED
ALLOY & TEMPER:
WEIGHT:
VOLUME:
SURFACE AREA:
PERIMETER:
FILE: FL 5179
FINISH TREATMENT:
Dimensional Tolerances
Unless Otherwise Specified
Decimals Angles
.X±.03
.XX ± .01 0' 30 min.
.XXX ± .005
SIMONTON°
UU WINDOWS
1 Cochrane Avenue
Pcnnsboro, WV 26415
SIZE:
B
DRAWING NO.:
IN0234
REV.:
13
DRAWN BY:
T.D.D.
DATE:
02/01/08
CHECKED BY:
DATE:
SCALE:
FIT
SHEET:
1 of 1
APPRV'D BY:
DATE:
SERIES:
41-18 HORIZONTAL SLIDER
TITLE:
2X BUCK INSTALLATION