345 BELVEDERE ST RESA21-0024 FL5414_R30_II_IN0160 43-06 43-17 SH 2X REV 12-14-21_1MODEL DESIGNATION:
MAXIMUM OVERALL NOMINAL SIZE: See Size Chart
DESIGN PRESSURE RATING: See Size Chart
USABLE CONFIGURATIONS: 0
Simonton Single
GENERAL DESCRIPTION:
2"
MAX.
X
Hung Series 43-06 / 43-17 Vinyl Window
The head, sill, and side jambs are extruded PVC. The wall thickness
through which the anchor screw penetrates is a minimum of 0.070".
8 1/2" O.C.
MAX. TYP.
2"
r MAX.
"H" MAX. OVERALL FRAME HEIGHT
X
N Q
"W" MAX. OVERALL FRAME WIDTH
SIZE CHART
OVERALL SIZE
DP RATING
WIDTH
»W»
HEIGHT
»H»
36"
72"
±25 PSF
48"
80"
44"
75"
±30 PSF
44"
63"
36"
74"
±35 PSF
53"
71"
36"
63"
±45 PSF
44"
63"
36"
84"
36"
74"
±50 PSF
32"
62"
SILICONE CAULK
SEE NOTES 12 & 13
#6 X 1 1/4" MIN. WOOD
SCREW WITH 1.00" MIN.
EMBEDMENT INTO WOOD
MIN. EDGE DIST., SEE NOTES
NO P.E. SEAL REQUIRED
INSTALLATION SUPPORTED
BY AAMA TEST REPORTS
ED
#6 X 1 1/4" MIN. WOOD
SCREW WITH 1.00" MIN.
EMBEDMENT INTO WOOD
MIN. EDGE DIST., SEE NOTES
SILICONE CAULK
SEE NOTES 12 Sc 13
2X BUCK
REV.
#:
REVISIONS:
REVISED BY:
DATE:
7
UPDATED 52" X 71" TO 53" X 71" PER NEW
TEST.
T.D.D.
02/04/13
8
ADDED MIN. EDGE DIST. NOTES
GJM
06/17/15
9
ADDED NOTES 12 & 13.
LMH
06/21/16
10
ADDED 36x63 TO SIZE CHART.
LMH
01/05/17
11
ADDED 44x75 TO SIZE CHART.
LMH
06/06/18
SILICONE CAULK
SEE NOTES 12 & 13
1/4" MAX. SHIM
#6 X 1 1/4" MIN. WOOD
SCREW WITH 1.00" MIN.
EMBEDMENT INTO WOOD
MIN. EDGE DIST., SEE NOTES
1/4" MAX. SHIM
SILICONE CAULK
SEE NOTES 12 & 13
SILL
2X BUCK
2X BUCK
SILICONE CAULK
SEE NOTES 12 & 13
1/4" MAX. SHIM
SILICONE CAULK
SEE NOTES 12 & 13
OJAMB
NOTES:
1. This installation has been evaluated for use in locations adhering to the Florida Building Code and where pressure requirements as
determined by ASCE 7 Minimum Design Loads for Buildings and Other Structures do not exceed the design pressure ratings herein, for use
outside the H.V.H.Z.
2. All interior and exterior perimeter surfaces of the window must be caulked.
3. Anchors shall be specified and spaced as shown Anchor embedment to base material shall be beyond wall dressing or stucco and into wood.
4. The responsibility for selection of Simonton products to meet any applicable local laws, building codes, ordinances, or other safety
requirements rests solely with the architect, building owner, or contractor.
5. Shims are optional. Maximum shim stack is 1/4".
6. Wood bucks (by others) must be engineered and anchored properly to transfer loads to the structure. Wood bucks shall be spruce -Pine -Fir.
Wood minimum specific gravity = 0.42 psi.
7. Wood screws must be at least Grade 5 for untis with a design pressure < 50 PSF, and at least Grade 8 for units with a design pressure
rating >_ 50 PSF.
8. When used in areas requiring impact protection, this product REQUIRES the use of approved impact resistant shutters or other external
protection.
9. Flashing should be applied using the ASTM E 2112 method appropriate for the opening into which the window is being installed.
10. Installation screws must be at least 1/2" from the edge of the wood.
11. This product complies with ASTM E 1300-04.
12. Use 100% pure silicone caulk compliant with AAMA 800 Section 1 - Sealant Specifications for use with Architectural Fenestration Products.
For more details see visit Simonton.com.
13. Use a backer rod on all joints >3/4" deep and/or wider than 1/4". Finished caulk joint should be a minimum of 3/8" deep.
DISCLOSURE STATEMENT
This document is the property of Simonton Windows, which
retains all proprietary and other rights to its subject matter.
This document is provided to the recipient on the expressed
condition that it is not to be disclosed, reproduced in whole or
part, nor used in conjunction with the design, manufacture or
repair of goods for anyone other than Simonton Windows
without its consent. This restriction does not limit the
recipient's rights to utilize information contained in this
document which is properly obtained from another source.
MATERIAL:
RMS FINISH:
EXCEPT AS NOTED
ALLOY & TEMPER:
WEIGHT:
VOLUME:
SURFACE AREA:
PERIMETER:
FILE: FL 5414.4
FINISH TREATMENT:
Dimensional Tolerances
Unless Otherwise Specified
Decimals Angles
.X±.03
.XX ± .01
.XXX ± .005
0' 30 min.
C0SIMON TON°
/ WINDOWS
1 Cochrane Avenue
Pennsboro, WV 26415
SIZE:
B
DRAWING NO.:
IN0160
REV.:
11
DRAWN BY:
T.D.D.
DATE:
11/09/07
CHECKED BY:
DATE:
SCALE:
FIT
SHEET:
1 of 1
APPRV'D BY:
DATE:
SERIES:
43-06 / 43-17 SINGLE HUNG
TITLE:
2X BUCK INSTALLATION