The URL can be used to link to this page

760 REDFIN DR ACC22-0022 FL13265_R6_II_HardieSoffit-Install-Instr REV 5-25-22_1Florida Product Approval HardieSoffit® Panel •For use inside HVHZ: o HardieSoffit Panel fastener types, fastening schedule, and installation shall be in accordance with the Miami-Dade County Florida NOA 20-0730.06. Consult the HardieSoffit product installation instructions on the following pages for all other installation requirements. •For use outside of HVHZ, o HardieSoffit Panel fastener types, fastening schedule, and installation shall be in accordance with Engineering Evaluation Report ER 2001-13.1 or 2001-13.2. Consult the HardieSoffit product installation instructions on the following pages for all other installation requirements. ACC22-0022 By Toni Gindlesperger at 4:15 pm, May 25, 2022By Mike Jones at 1:35 pm, Jun 09, 2022 GENERAL FASTENING REQUIREMENTS Fasteners must be corrosion resistant, galvanized, or stainless steel. Electro-galvanized are acceptable but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates. Manufacturers of ACQ and CA preservative-treated wood recommend spacer materials or other physical barriers to prevent direct contact of ACQ or CA preservative-treated wood and aluminum products. Fasteners used to attach HardieTrim Tabs to preserva- tive-treated wood shall be of hot dipped zinc-coated galvanized steel or stainless steel and in accordance to 2009 IRC R317.3 or 2009 IBC 2304.9.5 • Consult applicable product evaluation or listing for correct fasteners type and placement to achieve speciﬁed design wind loads. • NOTE: Published wind loads may not be applicable to all areas where Local Building Codes have speciﬁc jurisdiction. Consult James Hardie Technical Services if you are unsure of applicable compliance documentation. • Drive fasteners perpendicular to siding and framing. • Fastener heads should ﬁt snug against siding (no air space). • NOTE: Whenever a structural member is present, HardiePlank should be fastened with even spacing to the structural member. The tables allowing direct to OSB or plywood should only be used when traditional framing is not available. HardieSofﬁt® Panels SF1204 P2/3 04/19 Figure 5 • For wood frame construction a minimum 4d common nails spaced 8 in o.c. at panel edges and intermediate framing members spaced up to 24 in on center are suitable in most locations*. • For conventional 20ga - 16ga steel frame construction a minimum No. 8-18 x 0.323 in HD x 1 in long ribbed bugle screws spaced 6 in o.c. at panel edges and intermediate framing members spaced up to 24 in on center are suitable in most locations*. *Minimum Basic Wind Speed differs by locality. Where speciﬁed levels of wind resistance are required, refer to applicable Building Code Compliance Reports. FASTENER REQUIREMENTS Figure 6 Self-adheringmembrane Step flashing Housewrap Drip edge Kickoutﬂashing Self-adheringeaves membrane Because of the volume of water that can pour down a sloped roof, one of the most critical ﬂashing details occurs where a roof intersects a sidewall. The roof must be ﬂashed with step ﬂashing. Where the roof terminates, install a kickout to deﬂect water away from the siding. It is best to install a self-adhering membrane on the wall before the subfascia and trim boards are nailed in place, and then come back to install the kickout. KICKOUT FLASHING Figure 6, Kickout Flashing To prevent water from dumping behind the siding and the end of the roof intersection, install a "kickout" as required by IRC code R905.2.8.3 : “...ﬂashing shall be a min. of 4” high and 4” wide.” James Hardie recommends the kickout be angled between 100° - 110° to maximize water deﬂection PNEUMATIC FASTENING James Hardie products can be hand nailed or fastened with a pneumatic tool. Pneumatic fastening is highly recommended. Set air pressure so that the fastener is driven snug with the surface of the siding. A ﬂush mount attachment on the pneumatic tool is recommended. This will help control the depth the nail is driven. If setting the nail depth proves difﬁcult, choose a setting that under drives the nail. (Drive under driven nails snug with a smooth faced hammer - Does not apply for installation to steel framing). Figure 5 Maintain a minimum 1 in gap between gutter end caps and siding & trim. fascia siding 1 in min. gutter and end cap Manufacturers of ACQ and CA preservative-treated wood recommend spacer materials or other physical barriers to prevent direct contact of ACQ or CA preservative-treated wood and aluminum products. Fasteners used to attach HardieTrim Tabs to preservative-treated wood shall be of hot dipped zinc-coated galvanized steel or stainless steel and in accordance to 2009 IRC R317.3 or 2009 IBC 2304.9.5.” 3/8 in from edge of sofﬁt keep fasteners2 in awayfrom corners 24” o.c. max.Figure 4 Greater than 12 in Wide Sofﬁt Figure 3 1 in from end of sofﬁt 3/8 in from edge of sofﬁt less than or equal to 12 in Wide Sofﬁt ALUMINUM CLIPPED STAPLES HEAD NAILS FASTENERS UNDER DRIVE OVER DRIVE SLANT IF, THEN IF, THEN ADDITIONAL NAIL WOOD FRAME HAMMER FLUSH REMOVE & REPLACE COUNTERSINK & FILL STEEL FRAME FACE NAIL DO NOT DO NOT DO NOT USE AL SNUG FLUSH PAINTING CAULKING For best results use an Elastomeric Joint Sealant complying with ASTM C920 Grade NS, Class 25 or higher or a Latex Joint Sealant complying with ASTM C834. Caulking/Sealant must be applied in accordance with the caulking/sealant manufacturer’s written instructions. Note: some caulking manufacturers do not allow "tooling". DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie® Products. Factory-primed James Hardie products must be painted within 180 days of installation. 100% acrylic topcoats are recommended. Do not paint when wet. For application rates refer to paint manufacturers speciﬁcations. Back-rolling is recommended if the siding is sprayed. CUT EDGE TREATMENT Caulk, paint or prime all ﬁeld cut edges. James Hardie touch-up kits are required to touch-up ColorPlus products. HardieSofﬁt® Panels PAINTING JAMES HARDIE® SIDING AND TRIM PRODUCTS WITH COLORPLUS® TECHNOLOGYWhen repainting ColorPlus products, James Hardie recommends the following regarding surface preparation and topcoat application:• Ensure the surface is clean, dry, and free of any dust, dirt, or mildew• Repriming is normally not necessary• 100% acrylic topcoats are recommended• DO NOT use stain, oil/alkyd base paint, or powder coating on James Hardie® Products.• Apply ﬁnish coat in accordance with paint manufacturers written instructions regarding coverage, application methods, and application temperature• DO NOT caulk nail heads when using ColorPlus products, refer to the ColorPlus touch-up section COLORPLUS® TECHNOLOGY CAULKING, TOUCH-UP & LAMINATE • Care should be taken when handling and cutting James Hardie® ColorPlus® products. During installation use a wet soft cloth or soft brush to gently wipe off any residue or construction dust left on the product, then rinse with a garden hose. • Touch up nicks, scrapes and nail heads using the ColorPlus® Technology touch-up applicator. Touch-up should be used sparingly. If large areas require touch-up, replace the damaged area with new HardiePlank® lap siding with ColorPlus® Technology. • Laminate sheet must be removed immediately after installation of each course. • Terminate non-factory cut edges into trim where possible, and caulk. Color matched caulks are available from your ColorPlus® product dealer. • Treat all other non-factory cut edges using the ColorPlus Technology edge coaters, available from your ColorPlus product dealer. Note: James Hardie does not warrant the usage of third party touch-up or paints used as touch-up on James Hardie ColorPlus products. Problems with appearance or performance arising from use of third party touch-up paints or paints used as touch-up that are not James Hardie touch-up will not be covered under the James Hardie ColorPlus Limited Finish Warranty. SF1204 P3/3 04/19 Product warranties, safety information and additional installation information are available at jameshardiepros.com © 2019 James Hardie Building Products, Inc. All rights reserved TM, SM and ® denote trademarks or registered trademarks of James Hardie Technology Limited. WARNING: This product can expose you to chemicals including respirable crystalline silica, which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. RECOGNITION: In accordance with ICC-ES Evaluation Report ESR-2273, HardieSofﬁt® panel is recognized as a suitable alternate to that speciﬁed in the 2006, 2009, 2012 & 2015 International Residential Code for One and Two-Family Dwellings, and the 2006, 2009, 2012 & 2015 International Building Code. HardieSofﬁt panel is also recognized for application in the following: State of Florida Product Approval FL13265, Miami-Dade County Florida NOA No. 17-0406.06, U.S. Dept. of HUD Materials Release 1263f, Texas Department of Insurance Product Evaluation EC-23, City of New York MEA 223-93-M, and California DSA PA-019. These documents should also be consulted for additional information concerning the suitability of this product for speciﬁc applications. DANGER: May cause cancer if dust from product is inhaled. Causes damage to lungs and respiratory system through prolonged or repeated inhalation of dust from product. Refer to the current product Safety Data Sheet before use. The hazard associated with ﬁber cement arises from crystalline silica present in the dust generated by activities such as cutting, machining, drilling, routing, sawing, crushing, or otherwise abrading ﬁber cement, and when cleaning up, disposing of or moving the dust. When doing any of these activities in a manner that generates dust you must (1) comply with the OSHA standard for silica dust and/or other applicable law, (2) follow James Hardie cutting instructions to reduce or limit the release of dust; (3) warn others in the area to avoid breathing the dust; (4) when using mechanical saw or high speed cutting tools, work outdoors and use dust collection equipment; and (5) if no other dust controls are available, wear a dust mask or respirator that meets NIOSH requirements (e.g. N-95 dust mask). During clean-up, use a well maintained vacuum and ﬁlter appropriate for capturing ﬁne (respirable) dust or use wet clean-up methods - never dry sweep. SILICA WARNING