Loading...
1209 West Plaza ELEVATION 05.13.2015 (Revised) C,, J U.S.DEPARTMENT OF HOMELAND SECURITY ELEVATION CERTIFICATE FEDE;AL'EIIjRGENCY MANAGEMENT AGENCY OMB No. 1660-0008 IPational Flood Insurance Program Important: Read the instructions on pages 1-9. Expiration Date:July 31, 2015 SECTION A-PROPERTY INFORMATION FOR INSURANCE COMPANY USE Al. Building Owner's Name BRIAN S.VONN Policy Number: A2. Building Street Address(including Apt.,Unit,Suite,and/or Bldg.No.)or P.O. Route and Box No. Company NAIC Number: 1209 PLAZA STREET WEST City ATLANTIC BEACH State FL ZIP Code 32233 A3. Property Description(Lot and Block Numbers,Tax Parcel Number,Legal Description,etc.) LOTS 4,5&6,BLOCK 210,ATLANTIC BEACH SECTION H,AS RECORDED IN PLAT BOOK 18,PAGE 34,DUVAL CO A4. Building Use(e.g.,Residential,Non-Residential,Addition,Accessory,etc.) RESIDENTIAL A5. Latitude/Longitude:Lat.N30°19'58 Long.W81°25'33" Horizontal Datum: ❑ NAD 1927 ® NAD 1983 A6. Attach at least 2 photographs of the building if the Certificate is being used to obtain flood insurance. A7. Building Diagram Number 6 A8. For a building with a crawlspace or enclosure(s): A9. For a building with an attached garage: a) Square footage of crawlspace or enclosure(s) 1024 sq ft a) Square footage of attached garage N/A sq ft b) Number of permanent flood openings in the crawlspace b) Number of permanent flood openings in the attached garage or enclosure(s)within 1.0 foot above adjacent grade 3 within 1.0 foot above adjacent grade N/A c) Total net area of flood openings in A8.b 955 sq in c) Total net area of flood openings in A9.b N/A sq in d) Engineered flood openings? ® Yes 0 No d) Engineered flood openings? ❑ Yes ® No SECTION B-FLOOD INSURANCE RATE MAP(FIRM)INFORMATION BI.NFIP Community Name&Community Number B2.County Name B3.State DUVAL CO(ALL JURISDICTIONS), 120077 DUVAL FLORIDA B4.Map/Panel Number B5.Suffix B6.FIRM Index Date B7.FIRM Panel B8.Flood B9.Base Flood Elevation(s)(Zone 12031 C 0408 H 06/03/2013 Effective/Revised Date Zone(s) AO,use base flood depth) 06/03/2013 AE 5 B10. Indicate the source of the Base Flood Elevation(BFE)data or base flood depth entered in Item B9. ❑ FIS Profile ® FIRM 0 Community Determined ❑ Other/Source: B11. Indicate elevation datum used for BFE in Item B9: 0 NGVD 1929 ® NAVD 1988 ❑ Other/Source: B12. Is the building located in a Coastal Barrier Resources System(CBRS)area or Otherwise Protected Area(OPA)? ❑ Yes ® No Designation Date: ❑ CBRS 0 OPA SECTION C-BUILDING ELEVATION INFORMATION(SURVEY REQUIRED) Cl. Building elevations are based on: ❑ Construction Drawings* 0 Building Under Construction* ® Finished Construction *A new Elevation Certificate will be required when construction of the building is complete. C2. Elevations-Zones Al-A30,AE,AH,A(with BFE),VE,V1-V30,V(with BFE),AR,AR/A,AR/AE,AR/A1-A30,AR/AH,AR/AO.Complete Items C2.a-h below according to the building diagram specified in Item A7. In Puerto Rico only,enter meters. Benchmark Utilized:NAIL IN OAK TREE(4.01) Vertical Datum: NAVD 1988 Indicate elevation datum used for the elevations in items a)through h)below. ❑NGVD 1929 El NAVD 1988 0 Other/Source: Datum used for building elevations must be the same as that used for the BFE. Check the measurement used. a)Top of bottom floor(including basement,crawlspace,or enclosure floor) 6.86 ®feet 0 meters b)Top of the next higher floor 17.96 ®feet 0 meters c) Bottom of the lowest horizontal structural member(V Zones only) N/.A 0 feet 0 meters d)Attached garage(top of slab) 6.86 ®feet ❑meters e) Lowest elevation of machinery or equipment servicing the building 8.34 ®feet 0 meters (Describe type of equipment and location in Comments) f) Lowest adjacent(finished)grade next to building(LAG) 6.3 ®feet 0 meters g) Highest adjacent(finished)grade next to building(HAG) 6.5 ®feet 0 meters h) Lowest adjacent grade at lowest elevation of deck or stairs, including structural support N/A 0 feet 0 meters SECTION D-SURVEYOR, ENGINEER,OR ARCHITECT CERTIFICATION This certification is to be signed and sealed by a land surveyor,engineer,or architect authorized by law to certify elevation information./certify that the information on this Certificate represents my best efforts to interpret the data available. I understand that any false statement may be punishable by fine or imprisonment under 18 U.S. Code, Section 1001. \*��s OU"`mac ® Check here if comments are provided on back of form. Were latitude and longitude in Section A provided by a , `414 ,• . �r 0 Check here if attachments. licensed land surveyor? ® Yes 0 No ,r , cc r ' Certifiers Name H.BRUCE DURDEN Jr. License Number P.L.S.#4707 IP I • Title PRESIDENT A Company ame DURDEN SURVEYING AND MAPPING, INC. 441 Addres 18 10T EET NO- �� SONVILLE BEACH State FL ZIP Code 32250 i�- •. SignaturaNr i rffr45% .'./2013 Telephone 904-853-6822 ��/� �'��'y t �-if A Illlliitkt 'a / REA115E4* 1-11-6II5- FEMA Form 086-0-33(7/12) See reverse side for continuation. Replaces all previous editions. ELEVATION CERTIFICATE, page 2 RIPORTANT: In these spaces, copy the corresponding information from Section A. FOR INSURANCE COMPANY USE Building Street Address(including Apt., Unit,Suite,and/or Bldg. No.)or P.O.Route and Box No. Policy Number: 1209 PLAZA STREET WEST City ATLANTIC BEACH State FL ZIP Code 32233 Company NAIC Number: SECTION D-SURVEYOR, ENGINEER, OR ARCHITECT CERTIFICATION (CONTINUED) Copy both sides of this Elevation Certificate for(1)community official,(2)insurance agent/company,and(3)building owner. Comments SECTION A7)-ENTIRE FIRST FLOOR IS GARAGE SPACE,LIVING AREA IS ON SECOND FLOOR;SECTION A9d)-CONTRACTOR TO SUPPLY DOCUMENTATION;SECTION 2Ce)-EQUIPMENT SHOWN IS AIR CONDITIONING UNIT.WATER HEATER(LOCATED IN GARAGE) ELEVATION=8.21 ill REVISED FEB' RY ., • O CORRE� EMS • A8 D A9. Signature i / , - Date 12/06/2013 REVISEi7 2I7,4(t5- SECTION E-BUILDING ELEVATION INFOR ION(SURVEY NOT REQUIRED) FOR ZONE AO AND ZONE A(WITHOUT BFE) For Zones AO and A(without BFE),complete Items E1-E5.If the Certificate is intended to support a LOMA or LOMR-F request,complete Sections A,B, and C.For Items El-E4,use natural grade,if available.Check the measurement used. In Puerto Rico only,enter meters. El. Provide elevation information for the following and check the appropriate boxes to show whether the elevation is above or below the highest adjacent grade(HAG)and the lowest adjacent grade(LAG). a)Top of bottom floor(including basement,crawlspace,or enclosure)is ❑feet 0 meters 0 above or 0 below the HAG. b)Top of bottom floor(including basement,crawlspace,or enclosure)is 0 feet 0 meters 0 above or 0 below the LAG. E2. For Building Diagrams 6-9 with permanent flood openings provided in Section A Items 8 and/or 9(see pages 8-9 of Instructions),the next higher floor (elevation C2.b in the diagrams)of the building is ❑feet 0 meters 0 above or 0 below the HAG. E3. Attached garage(top of slab)is 0 feet 0 meters ❑above or 0 below the HAG. E4. Top of platform of machinery and/or equipment servicing the building is 0 feet 0 meters 0 above or❑below the HAG. E5. Zone AO only: If no flood depth number is available,is the top of the bottom floor elevated in accordance with the community's floodplain management ordinance? ❑Yes 0 No 0 Unknown.The local official must certify this information in Section G. SECTION F-PROPERTY OWNER(OR OWNER'S REPRESENTATIVE)CERTIFICATION The property owner or owner's authorized representative who completes Sections A,B,and E for Zone A(without a FEMA-issued or community-issued BFE) or Zone AO must sign here.The statements in Sections A,B,and E are correct to the best of my knowledge. Property Owner's or Owner's Authorized Representative's Name Address City State ZIP Code Signature Date Telephone Comments ❑Check here if attachments. SECTION G-COMMUNITY INFORMATION(OPTIONAL) The local official who is authorized by law or ordinance to administer the community's floodplain management ordinance can complete Sections A,B,C(or E),and G of this Elevation Certificate.Complete the applicable item(s)and sign below.Check the measurement used in Items G8-G10.In Puerto Rico only,enter meters. G1.0 The information in Section C was taken from other documentation that has been signed and sealed by a licensed surveyor,engineer,or architect who is authorized by law to certify elevation information. (Indicate the source and date of the elevation data in the Comments area below.) G2.0 A community official completed Section E for a building located in Zone A(without a FEMA-issued or community-issued BFE)or Zone AO. G3.❑ The following information(Items 04-G10)is provided for community floodplain management purposes. G4.Permit Number G5. Date Permit Issued G6. Date Certificate Of Compliance/Occupancy Issued 13- COCO2,622- G7. This permit has been issued for: 0 New Construction 0 Substantial Improvement G8. Elevation of as-built lowest floor(including basement)of the building: 0 feet 0 meters Datum G9. BFE or(in Zone AO)depth of flooding at the building site: 0 feet 0 meters Datum G10.Community's design flood elevation: ❑feet 0 meters Datum Local Official's Name 11.tTitle '^ Community Name G oF T # �� 6 F_Ac._ Telephone 4 0 4 _ /. -r _ �� 1 Signature „.....34:& Date Z /2- 6 /r c Comments 1 L__10A - ) L — ( t4 k L— T- �► r'{ OF k-r-`ic- CA c_14 I Z 007 5 ❑Check here if attachments. L.s.le. GZ.A - 6-KKA -c.-r FA A t5 6'?ke_t.-(5 Iwe- CALL DS0-6- Las-rf-D t4 L1 - 3f.6- FEMA Form 086-0-33(7/12) Replaces all previous editions. ELEVATION CERTIFICATE, page 3 Building Photographs See Instructions for Item A6. IMPORTANT: In these spaces, copy the corresponding information from Section A. FOR INSURANCE COMPANY USE Building Street Address(including Apt., Unit,Suite,and/or Bldg.No.)or P.O.Route and Box No. Policy Number: 1209 PLAZA STREET WEST City ATLANTIC BEACH State FL ZIP Code 32233 Company NAIC Number: If using the Elevation Certificate to obtain NFIP flood insurance, affix at least 2 building photographs below according to the instructions for Item A6. Identify all photographs with date taken; "Front View" and "Rear View"; and, if required, "Right Side View" and "Left Side View." When applicable, photographs must show the foundation with representative examples of the flood openings or vents, as indicated in Section A8. If submitting more photographs than will fit on this page, use the Continuation Page. FRONT VIEW- 12/6/2013 3 s" " 0' ' . 401}. 4t, .4"..4.... ... . • 'j i Iltill ' I Ai, * „. fp . i i , f , M - f r n LEFT VIEW- 12/6/2013 VIEW OF FLOOD VENT AND NC UNIT 1.* i :,71,1"..ii:. . 1- ' .ht 1411g,y 41116 Wei • It �" a 1 — �—>> j fiy- w f FEMA Form 086-0-33(7/12) Replaces all previous editions. ELEVAT'2N CERTIFICATE, page 4 Building Photographs Continuation Page IMPORTANT: In these spaces, copy the corresponding information from Section A. FOR INSURANCE COMPANY USE Building Street Address(including Apt.,Unit,Suite,and/or Bldg. No.)or P.O. Route and Box No. Policy Number: 1209 PLAZA STREET WEST City ATLANTIC BEACH State FL ZIP Code 32233 Company NAIC Number: If submitting more photographs than will fit on the preceding page, affix the additional photographs below. Identify all photographs with: date taken; "Front View" and "Rear View"; and, if required, "Right Side View" and "Left Side View." When applicable, photographs must show the foundation with representative examples of the flood openings or vents, as indicated in Section A8. REAR VIEW- 12/6/2013 h t w ? 3 � = . , .a I M h ay4 * - F�! l It f} i��1i�11111NINu1111!. .1!1 Ii'it , r n ltd. -i:il-'`,'''*--`I"-'*iik;, R e,q 6� F NIEL _ i RIGHT VIEW- 12/6/2013 e a 'III s �il . I '' '� + . . .-":•.:' :''1,'., "'.. '--i4' .. i i r ''.'...,..;'1_,:',_. .- Sir $, �k , _°' * e a nj .R YC . 3 2 *4:I..' ' ,. " J iso• J• '1., , .-0.0 . FEMA Form 086-0-33(7/12) Replaces all previous editions. S , EZ ICC EVALUATION SERVICE Most Widely Accepted and Trusted ICC-ES Evaluation Report ESR-2074 FBC Supplement Issued July 2013 This report is subject to renewal February 1, 2015. www.icc-es.orq I (800)423-6587 I (562) 699-0543 A Subsidiary of the International Code Council® DIVISION: 08 00 00—OPENINGS Section: 08 95 43—Vents/Foundation Flood Vents REPORT HOLDER: SMARTVENT PRODUCTS, INC. 430 ANDBRO DRIVE, UNIT 1 PITMAN, NEW JERSEY 08071 (877)441-8368 www.smartvent.com infoAsmartvent.com EVALUATION SUBJECT: SMART VENT° AUTOMATIC FOUNDATION FLOOD VENTS: FLOODVENTTM MODEL #1540-520; FLOODVENTTM STACKING MODEL#1540-521; SMARTVENTTM MODEL#1540-510; SMARTVENTTM STACKING MODEL#1540-511;WOOD WALL FLOOD MODEL#1540-570;WOOD WALL FLOOD OVERHEAD DOOR MODEL#1540574; FLOODVENTTM OVERHEAD DOOR MODEL #1540-524;SMARTVENTTM OVERHEAD DOOR MODEL#1540-514 1.0 REPORT PURPOSE AND SCOPE Purpose: The purpose of this evaluation report supplement is to indicate that Smart Vent®Automatic Foundation Flood Vents, recognized in ICC-ES master report ESR-2074, have also been evaluated for compliance with the codes noted below. Applicable code editions: • 2010 Florida Building Code—Building(FBC) • 2010 Florida Building Code—Residential(FRC) 2.0 CONCLUSIONS The Smart Vent® Automatic Foundation Flood Vents, described in Sections 2.0 through 7.0 of the master evaluation report ESR-2074, comply with the FBC and the FRC, provided the design and installation are in accordance with the International Building Code®provisions noted in the master report. Use of the Smart Vent®Automatic Foundation Flood Vents has also been found to be in compliance with the High-Velocity Hurricane Zone provisions of the FBC and the FRC for structures not subject to FBC Section 2326.3.1 or FRC Section 4409.13.3.1, as applicable. For products falling under Florida Rule 9N-3, verification that the report holder's quality assurance program is audited by a quality assurance entity approved by the Florida Building Commission for the type of inspections being conducted is the responsibility of an approved validation entity (or the code official when the report holder does not possess an approval by the Commission). This supplement expires concurrently with the master report reissued December 1, 2012, revised June 2014. ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed,nor are they to be construed Kolb"— as an endorsement of the subject of the report or a recommendation for its use.There is no warranty by ICC Evaluation Service,LLC,express or implied as to any finding or other matter in this report,or as to any product covered by the report. Copyright©2013 Page 1 of 1 ESR-2074 I Most Widely Accepted and Trusted Page 2 of 2 concrete walls up to 12 inches (305 mm) thick. In order to 5.1 The Smart Vent® AFFVs must be installed in comply with the engineered opening design principle noted accordance with this report, the applicable code and in Section 2.6.2.2 of ASCE/SEI 24, the Smart Vent®AFFVs the manufacturer's installation instructions. In the must be installed as follows: event of a conflict, the instructions in this report • With a minimum of two openings on different sides of govern. each enclosed area. 5.2 The Smart Vent® AFFVs must not be used in the • With a minimum of one AFFV for every 200 square place of "breakaway walls" in coastal high hazard break, feet (18.6 m2) of enclosed area, except that the butare permitted for use in conjunction with h SmartVENTTM Stacking Model #1540-511 and breakaway walls inn other areas. FloodVENTTM Stacking Model #1540-521 must be 6.0 EVIDENCE SUBMITTED installed with a minimum of one AFFV for every Data in accordance with the ICC-ES Acceptance Criteria 400 square feet(37.2 m2)of enclosed area. for Automatic Foundation Flood Vents (AC364), dated • Below the base flood elevation. October 2013 (editorially revised May 2014). • With the bottom of the AFFV located a maximum of 7.0 IDENTIFICATION 12 inches (305.4 mm) above grade. The Smart VENT® models recognized in this report must 5.0 CONDITIONS OF USE be identified by a label bearing the manufacturer's name (Smartvent Products, Inc.), the model number, and the The Smart Vent® AFFVs described in this report comply evaluation report number(ESR-2074). with, or are suitable alternatives to what is specified in, those codes listed in Section 1.0 of this report, subject to the following conditions: ICC EVALUATION SERVICE Most Widely Accepted and Trusted ICC-ES Evaluation Report ESR-2074* Reissued December 2012 This report is subject to renewal February 1, 2015. www.icc-es.orq I (800) 423-6587 I (562) 699-0543 A Subsidiary of the International Code Council® DIVISION: 08 00 00—OPENINGS pressure from one side of the foundation to the other. The Section: 08 95 43—Vents/Foundation Flood Vents AFFV pivoting door is normally held in the closed position by a buoyant release device. When subjected to rising REPORT HOLDER: water, the buoyant release device causes the unit to unlatch, allowing the plate to rotate out of the way and SMARTVENT PRODUCTS, INC. allow flow. The water level stabilizes, equalizing the lateral 430 ANDBRO DRIVE, UNIT 1 forces. Each unit is fabricated from stainless steel. The PITMAN, NEW JERSEY 08071 SmartVENTTM Stacking Model #1540-511 and (877)441-8368 FloodVENTTM Stacking Model #1540-521 units each www.smartvent.com contain two vertically arranged openings per unit. info(cDsmartvent.com 3.2 Engineered Opening: EVALUATION SUBJECT: The AFFVs comply with the design principle noted in Section 2.6.2.2 of ASCE/SEI 24 for a maximum rate of rise SMART VENT` AUTOMATIC FOUNDATION FLOOD VENTS: and fall of 5.0 feet per hour (0.423 mm/s). In order to FLOODVENTTM MODEL #1540-520; FLOODVENTM comply with the engineered opening requirement of STACKING MODEL #1540-521; SMARTVENTTM MODEL ASCE/SEI 24, Smart Vent AFFVs must be installed in #1540-510; SMARTVENTTM STACKING MODEL #1540-511; accordance with Section 4.0. WOOD WALL FLOOD MODEL #1540-570; WOOD WALL 3.3 Model Sizes: FLOOD OVERHEAD DOOR MODEL #1540-574; FLOODVENTTM OVERHEAD DOOR MODEL #1540-524; The FloodVENTTM Model#1540-520, SmartVENTTM Model SMARTVENTTM OVERHEAD DOOR MODEL#1540-514 #1540-510, FloodVENTTM Overhead Door Model #1540-524, and SmartVENTTM Overhead Door Model 1.0 EVALUATION SCOPE #1540-514 units measure 153/4 inches wide by 73/4 inches Compliance with the following codes: high (400 by 196.9 mm). The Wood Wall Flood Model #1540-570 and Wood Wall Flood Overhead Door Model • 2009 and 2006 International Building Code®(IBC) #1540-574 units measure 14 inches wide by 83/4 inches • 2009 and 2006 International Residential Code®(IRC) high (355.6 by 222.25 mm). The SmartVENTTM Stacking Model #1540-511 and FloodVENTTM Stacking Model Properties evaluated: #1540-521 units measure 16 inches wide by 16 inches • Physical operation high (406.4 by 406.4 mm). • Water flow 3.4 Ventilation: 2.0 USES The SmartVENT® Model #1540-510 and SmartVENT® ® Overhead Door Model#1540-514 both have screen covers The Smart Vent® units are automatic foundation flood with 1/4-inch-by-1/4-inch (6.35 by 6.35 mm) openings, vents (AFFVs) employed to equalize hydrostatic pressure yielding 51 square inches (32 903 mm2) of net free area on nonfire-resistance-rated foundation walls, rolling-type to supply natural ventilation. The SmartVENTTM Stacking overhead doors and building walls subject to rising or ® Model #1540-511 consists of two Model #1540-510 falling flood waters. The Smart Vent®units are intended for units in one assembly, and provides 102 square inches use where flood hazard areas have been established in (65 806 mm2) of net free area to supply natural ventilation. accordance with IBC Section 1612.3 or IRC Section Other AFFVs recognized in this report do not offer natural R3222.1. Certain models also allow natural ventilation in ventilation. accordance with Section 1203 of the IBC or Section 408.1 of the IRC. 4.0 INSTALLATION 3.0 DESCRIPTION SmartVENT® and FloodVENTTM are designed to be 3.1 General: installed into walls or overhead doors of existing or new construction from the exterior side. Installation of the vents When subjected to pressure from rising water, the Smart must be in accordance with the manufacturer's Vent® AFFVs disengage, then pivot open to allow flow in instructions, the applicable code and this report. The either direction to equalize water level and hydrostatic mounting straps allow mounting in wood, masonry and *Revised June 2014 ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed nor are they to be construed 1 as an endorsement of the subject of the report or a recommendation for its use.There is no warranty by ICC Evaluation Service,LLC,express or implied as `a---�,,, to any finding or other matter in this report,or as to any product covered by the report. Copyright©2014 Page 1 of 2 . BUILDING DROPS 127 W. Fairbanks Ave. . Suite 438 • A Perfect Solution in Every Drop4 Winter Park, FL 32789 Certificate of Authorization:29578 407.644.6957 PH 407.644.2366 FX contact@buildingdrops.com Product Evaluation Report of Smart Vent Products, Inc. "FloodVent Model #1540-520" "SmartVent Model #1540-510" "Wood Wall Flood Model #1540-570" "Wood Wall Flood Overhead Door Model #1.540-574" "FloodVent Overhead Door Model #1540-524" "SmartVent Overhead Door Model #1540-5.14" for Florida Product Approval FL# FL5822-R2 Report No. 1550 Florida Building Code 2007 & 2010 Per Rule 9N-3 Method: 2—B(Engineering Evaluation) Category: Structural Components Sub—Category: Products Introduced as a Result of New Technology Other Sub-Category: Ventilation Product: Automatic Foundation Flood Vents (AFFV) Material: Stainless Steel Product Dimensions: Foundation Dimensions-15 3/4"x 7 3/" Wood Wall Dimensions-14"x 8 3/" Prepared For: Smart Vent Products, Inc. ���toltiiSP` , 430 Andbro Drive, Unit 1 �. Xx5 Y R� I. Pitman, NJ 08071 `,,. lie •Q\' *GE•Nvs�• G'., ALEX SPYROU • • No Prepared by: _ * ' 2011 .12.14 Alexis Spyrou, P.E. • A/ —-0: � Florida Professional Engineer#68101 :t.�' TATE OF •�1 21 :11 :53 -05 00 Date: 11/28/2011 %'�� As/ O R O P•'•V°.•,....\'0 ,%` Contents: Evaluation Report Pages Pages 1 —3 .�,''SS;O N A�� �% Alexis Spyrou, P.E. Florida No. 68101 • • BUILDING DROPS FL#: FL5822-R2 Date: 11/28/2011 41 . A Perfect Solution in Every Drop Report No: 1550 Certificate of Authorization:29578 Manufacturer: Smart Vent Products, Inc. Product Category: Structural Components Product Sub-Category: Other Other Sub-Category: Ventilation Compliance Method: State Product Approval Rule 9N-3.005 (2)(b) Product Name: FloodVent Model#1540-520 SmartVent Model#1540-510 Wood Wall Flood Model#1540-570 Wood Wall Flood Overhead Door Model#1540-574 FloodVent Overhead Door Model#1540-524 SmartVent Overhead Door Model#1540-514 Foundation Dimensions-15 3/4"x 73/4" Wood Wall Dimensions-14"x 83/4" Scope: This is a Product Evaluation Report issued by Alexis Spyrou, P.E. (FL#68101)for Smart Vent Products, Inc.based on Rule Chapter No. 9N-3.005, Method 2b of the State of Florida Product Approval, Department of Community Affairs-Florida Building Commission. Alexis Spyrou, P.E.does not have nor will acquire financial interest in the company manufacturing or distributing the product or in any other entity involved in the approval process of the product named herein. This product has been evaluated for use in locations adhering to the 2007&2010 Florida Building Code. See Installation Instructions provided by Smart Vent Products, Inc.,verified by Alexis Spyrou, P.E. (FL #68101)for specific use parameters. Limits of Use: 1. This product has been evaluated and is in compliance with the 2007&2010 Florida Building Code, including the "High Velocity Hurricane Zone"(HVHZ). 2. Product anchors shall be as listed and spaced as shown on details. Anchor embedment into substrate material shall be beyond wall dressing or stucco. 3. When used in areas requiring wind borne debris protection this product complies with Section 1609.1.2 of the Florida Building Code and does not require an impact resistant covering. Alexis Spyrou, P.E. Florida No.68101 Page 2 of 3 BUILDING DROPS FL#: FL5822-R2 ` . Date: 11/28/2011 A Perfect Solution in Every Drop Report No: 1550 Certificate of Authorization:29578 Limits of Use(cont.): 4. Site conditions that deviate from the details of the drawings require further engineering analysis by a licensed engineer or registered architect. 5. See Installation Instructions for size and design pressure limitations. 6. Wall construction shall meet requirements of Section 1612 and Appendix G of the FBC as deemed technically relevant due to site conditions. Quality Assurance: The manufacturer has demonstrated compliance of ventilation products in Accordance with the Florida Building Code and Rule 9N-3 for manufacturing under a quality assurance program audited by an approved quality assurance entity through Architectural Testing, Inc. (FBC Organization #: QUA 1844) Performance Standards: The product described herein has been tested per: • ASTM E 330-02 • ASCE 24-05 • TAS 202-94 Code Compliance: The product described herein complies with 2010 FBC Section 1714.2 and the intent of 2010 FBC Section 1612.5(1)(1.2). Referenced Data: 1. Product Testing performed by Architectural Testing, Inc. (FBC Organization#TST1558) Report#:01-42966.01, Report Date: 11/15/02 Report#: 38957.102-122-44, Report Date: 11/16/05 Report#: 60619.01-122-47, Report Date: 11/16/05 Report#: 61877.01-122-44, Report Date: 01/06/06 Report#: 94135.01-109-18, Report Date: 08/31/09 2. Quality Assurance Architectural Testing, Inc. (FBC Organization#: QUA 1844) 3. ICC Evaluation Service ESR-2074: Meets requirements of AC364 Reissued February 1, 2011 Installation: Refer to Installation Instructions by Manufacturer for installation requirements. Design Pressure: Design Pressures +100/-100 PSF Alexis Spyrou, P.E. Florida No. 68101 Page 3 of 3