1505 , 1507 RICHARDSON LN RES21-0187 , 0188 ARCH. DWGS_17/16" OSB
7/16" OSB
1/2" FIRE RETARDING PLYWOOD
7/16" OSB1/2" FIRE RETARDING PLYWOOD
7/16" OSB7/16" OSB
7/16" OSB
1/2" FIRE RETARDING PLYWOOD
1/2" FIRE RETARDING PLYWOOD
1/2" FIRE RETARDING PLYWOOD
1/2" FIRE RETARDING PLYWOOD
4'4'
MINIMUM COVERAGE EACH SIDE OF PARTY WALL
DENSGLASS PARTY WALL BELOW
ROOF SHEATHING DETAIL AT PARTY WALL
SCALE: 1/4" = 1'-0"
FIRE RATED WALL SHEATHING 4' ON BOTH SIDES OF ADJACENT UNITS.3'TYPICAL WALL SECTION
SCALE : 1" = 1'-0"
DRYWALL OR OTHER FINISH
MATERIAL IF APPLICABLE
SEE ELEVATIONS FOREXTERIOR FINISH MATERIAL
R13 INSULATION
R-30INSULATION
5/8" GYP. BOARD
NOTE: THIS WALL SECTION IS FOR
AESTHETIC PURPOSES ONLY.
VERIFY ALL CONDITIONS SHOWN
WITH BUILDER. SEE STRUCTURAL
PLANS FOR CONNECTIONS AND
TIE DOWN INFORMATION.
BEARING HEIGHT
PRE-ENGINEERED TRUSS ROOF SYSTEM
FIBERGLASS SHINGLES ON
15# FELT OVER 7/16" O.S.B.
WITH 1/2" CLIPS
FASCIA STYLE PERBUILDER
VINYL SOFFIT (TYP.)
R-38
INSULATION
TYPE "X" 5/8" GYPSUMBOARD
1'-4" UNLESS
OTHERWISE NOTED
16" FLOOR TRUSS
DRYWALL OR OTHER FINISH
MATERIAL IF APPLICABLE
R13 INSULATION
2ND FLOOR
2"X4" FRAMING (TYP.)
2"X4" FRAMING (TYP.)
12
RP SEE
ELEV.
TYPE "A" FLASHING
TYPE "C" FLASHING (WHERE
EXTERIOR BUILDING PANELSJOIN HORIZONTALLY)
TYPE "B" FLASHING
(WHERE CHIMNEYS AND
WALLS MEET ROOF)
DOUBLE 2X TOP PLATE WITH
APPROVED HURRICANE
ANCHOR AT ENDS OF EACH
TRUSS
*IF WITHIN 3' OF PROPERTY LINE, FIRE
BLOCK AND FIRE CAULK BETWEEN
TRUSSES TO BOTTOM OF ROOF DECK
FIRE CAULKED*
2X BLOCKING*
TYPICAL ATTIC PARTY WALL - UL DESIGN: U373
SCALE: 1" = 1'-0"
C-CHANNEL SCREWED TO DECKING
ROOF DECKING
ROOF TRUSS (TYP.)
1" DENSGLASS ULTRA
1/2" DRYWALL
FIRE BLOCKING
2"X4" STUDS @ 16"O.C.
3/4" AIR SPACE
CONTINUE THIS DETAIL THROUGH SOFFIT
TYPICAL PARTY WALL 2ND FLOOR
UL DESIGN: U373
SCALE: 1" = 1'-0"
1"
DENSGLASSULTRA
1/2" DRYWALL
FIRE BLOCKING AS REQUIRED
2"X4" STUDS @ 16"O.C.
3/4" AIR SPACE
16" FLOOR TRUSS
1/2" DRYWALL
2"X4" STUDS @ 16"O.C.
3/4" AIR SPACE
1/2" DRYWALL
2"X4" STUDS @ 16"O.C.
(R-13 INSULATION)
3/4" AIR SPACE
1/2" DRYWALL
C-CHANNEL
TYPICAL PARTY WALL TO SLAB
UL DESIGN: U373
SCALE: 1" = 1'-0"
2"X4"PLATE WITH SEALANT
C-CHANNEL
CONCRETE SLAB
TYPICAL OFFSET WALL BETWEEN UNITS
UL DESIGN: U373
SCALE: 1" = 1'-0"
1/2" DRYWALL
2"X4" STUDS @ 16"O.C.
(R-13 INSULATION)
1"
DENSGLASS
ULTRA
3/4" AIR SPACE
C-CHANNEL
1/2" DRYWALL
1/2" DENSARMOR PLUS OR 1/2" TOUGHROCK GYP.BOARD.
2
3
1
FRAME PARTY WALL CONSTRUCTION
UL DESIGN: U373
SCALE: 1" = 1'-0"
4
2
3
1
4
1
2
3
4
2"X4" STUD WALL @ 16" O.C. FROM TOP OF SECOND
FLOOR DECKING TO BOTTOM CHORD OF ROOF TRUSSES,
R-11 TOTAL PER PARTY WALL.
3/4" AIR SPACE BETWEEN STUD WALL AND DENSGLASSSHAFTLINER (DRAFT STOPPING AS REQUIRED PER FBC R-302.12).
DOUBLE LAYER OF 1" THICK DENSGLASS ULTRA SHAFTLINER JOINED WITH H-STUDS. C-TRACK AND ALUMINUM
ANGLE CLIPS AS REQUIRED PER MANUFACTURERS
SPECIFICATIONS.
SECTION A-ATHROUGH WINDOW JAMB
FLASHING
SEALANT BEAD
BEHIND MOUNTINGFLANGE.
JAMB FLASHING4
1
STEPS
2
3
4
WEATHER RESITIVE BARRIER (WRB) APPLIED PRIOR TO THE WINDOW INSTALLATION.
FLASHING APPLIED OVER THE FACE OF THE MOUNTING FLANGE.
SECURE WRBAT HEAD
HEAD FLASHING
A
61 8 12"A
JAMB FLASHING
6
6
3
IN WATER SHEDDING FASHION, STARTING AT THEBASE OF THE WALL & WORKING TOWARDS THE TOP,
INSTALL THE WRB TO THE FACE OF THE SHEATHING.CUT AT INVERTED "Y".
CUTLINE
INSTALL 6" WIDE SELF ADHESIVE SILL FLASHING THATEXTENDS 4" BEYOND OPENING.
9"
SHIM AND ADJUST WINDOW TO ACHIEVE SQUARE,
PLUMB, AND LEVEL CONDITION. USE CORROSIONRESISTANT FASTENERS. FASTEN WINDOWS PER
WINDOW MANUFACTURER SPECIFICATIONS.
SILL FLASHING
9"
1
9"135°
1
SEALANT
WINDOW INSTALLATION
SCALE: N.T.S.
5
APPLY A 4" SELF ADHESIVE JAMB FLASHING OVERLAPPING THEWINDOW FLANGE EXTENDED 4" PAST THE ROUGH OPENING.
APPLY BEAD OF SEALANT AT BACK OF WINDOWFLANGE & SET WINDOW USING PAN HEAD SCREWS
TO FACILITATE INSPECTION.
REMOVE PREVIOUSLY APPLIED TAPE,ALLOWING WRB TO LAY FLAT OVER HEAD
FLASHING. APPLY NEW SHEATHING TAPEOVER DIAGONAL CUT - SEE DIAGRAM.
FLASHING AT HEAD EXTENDS
1" BEYOND JAMB FLASHING.
5
6
EXTEND JAMB FLASHING TO
OVERLAP SILL FLASHING. EXTENDJAMB FLASHING 8-1/2" ABOVE
ROUGH OPENING AT HEAD. TUCKTOP OF JAMB FLASHING UNDER
THE FLAP OF WRB AT THE HEAD.SEE DIAGRAM.
INTERIOR VIEW
TOP LEFT CORNER OF WINDOW
APPLY CONT. SELF ADHESIVE FLASHING THATEXTENDS AT LEAST 4" BEYOND ROUGH OPENING.
EMBED BOTTOM OF THE HEAD FLASHING
AGAINST THE PREVIOUSLY APPLIEDSEALANT (FLASHING GOES OVER SEALANT).
EXTEND HEAD FLASHING BEYOND EACHJAMB FLASHING. FASTEN IN PLACE.
AT A 45 DEGREE ANGLE,CAREFULLY CUT THE BARRIER ONA DIAGONAL. GENTLY RAISE THETOP EDGE OF THE BARRIER UP AND
TAPE THE TOP CORNERS ANDCENTER TO THE EXTERIOR WRB
SURFACE ABOVE.
APPLY A 4" SELF ADHESIVE HEAD FLASHING OVERLAPPING THEWINDOW FLANGE EXTENDED 4" PAST THE ROUGH OPENING.
WEATHER RESISTANT BARRIER (WRB)
5
FLASHING DETAILS AND SHINGLE INFORMATION
SCALE : 3" = 1'-0"
SHINGLES:
UL CLASS A FIRE RATING: ASTM D 3018, TYPE I
VALLEY FLASHING:
26 GA. GALVANIZED, 18" WIDE
FASTENING:
(4) 11 OR 12 GAUGE NAILS 1-1/4" LONG WITH 3/8" Ø HEAD
UL WIND RESISTANCE:
UASTM D 3161, TYPE I (MODIFIED TO 110 MPH)2-1/2"2-3/4"
26 GAUGE GALVANIZED
2-1/2" METAL DRIP EDGEA
5"5"26 GAUGE GALVANIZED
5"X5" ANGLE FLASHINGB 32 GAUGE GALVANIZED
"Z" FLASHINGC1/2"2-1/8"3/8" OR 5/8"
PIPE BOOT
GALVANIZED METAL FLANGE
PLUMBING STACK FLASHING DETAIL
NOT TO SCALE
OFF RIDGE VENT DETAIL
NOT TO SCALE
FIBERGLASS SHINGLE ROOFING OVER
UNDERLAYMENT
INSTALL SHINGLES OVER ORV VENT
FLANGE AT HEAD
GALVANIZED METAL ORV WITH BAFFLE SET IN
PLASTIC ROOF CEMENT OR SEALANT
SCREEN
INSTALL ORV FLANGE OVERSHINGLES AT BASE
7/16" OSB OVER
PRE-ENGINEERED WOOD
TRUSSES
OVER PRE-ENGINEERED
WOOD TRUSSES
VALLEY FLASHING DETAIL
NOT TO SCALE
24" WIDE METAL VALLEY
FLASHING OVER 15# FELTOVER 7/16" OSB
VALLEY SHINGLE INSTALLATION:
INSTALL SHINGLES USING WEAVE METHOD
1. EXTEND (1) FULL END SHINGLE MINIMUM 12" PAST CENTER
LINE OF VALLEY. SEE MANUFACTURERS WRITTEN
INSTRUCTIONS FOR ADDITIONAL INSTALL INFORMATION.
2. DO NOT NAIL MINIMUM 6" FROM VALLEY CENTER LINE.
DOOR FLASHING INSTALLATION AND DETAIL
SCALE: N.T.S.
APPROVED WEATHER BARRIER OVER USB
CUT WEATHER BARRIER IN ANDAROUND JAMBS
SET THRESHOLD IN BED OF
SEALANT
INSTALL 4" WIDE SELF-ADHERING
MEMBRANE FLASHING OVERLAPPING DOOR
FRAME BY 1/4" AND 1" BEYOND DOOR JAMB
INSTALL 4" WIDE SELF-ADHERING
MEMBRANE FLASHING OVERLAPPING
DOOR FRAME BY 1/4"
R703.8 FLASHING:
APPROVED CORROSION-RESISTANT FLASHING SHALL BE APPLIED
SHINGLE-FASHION IN SUCH A MANOR TO PREVENT ENTRY OF WATER INTO THE
WALL CAVITY OR PENETRATION OF WATER TO THE BUILDING STRUCTURAL
FRAMING COMPONENTS. THE FLASHING SHALL EXTEND TO THE SURFACE OF THEEXTERIOR WALL FINISH. APPROVED ANTI-CORROSION RESISTANT FLASHING SHALL
BE INSTALLED AT ALL OF THE FOLLOWING LOCATIONS:
1. AT THE INTERSECTION OF CHIMNEYS OR OTHER MASONRY CONSTRUCTION WITH
FRAME OR STUCCO WALLS, WITH PROJECTING LIPS ON BOTH SIDES UNDER STUCCO
COPINGS.
2. UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL COPINGS AND SILLS.
3. CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM.
4. WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A WALL OR FLOORASSEMBLY OR WOOD FRAMED CONSTRUCTION.
5. AT ALL WALL AND ROOD INTERSECTIONS.
6. AT BUILT IN GUTTERS.
GUARDRAIL NOTE:
DEPENDING ON FIELD CONDITIONS, DIMENSIONS MAY VARY BUT MUST COMPLY WITH FLORIDA BUILDING
CODES R312.1-R312.2 FOR GUARDRAIL REQUIREMENTS AND OPENINGS.
*HEIGHT SHALL BE 36" MIN. WHEN PORCH, BALCONY OR RAISED FLOOR EXCEEDS 30" ABOVE FLOOR OR
GRADE AND SHALL BE 34" ON OPEN SIDES OF STAIRS THAT EXCEED 30" OR MORE ABOVE FLOOR OR
GRADE.
*OPENINGS SHALL HAVE INTERMEDIATE RAILS OR CLOSURES WHICH DO NOT ALLOW PASSAGE OF
SPHERE 4" OR GREATER IN DIAMETER. REQUIRED GUARD RAILS ON THE SIDES OF STAIR TREADS SHALL
NOT ALLOW SPHERE GREATER THAN 4-3/8" IN DIAMETER TO PASS THROUGH.
GENERAL NOTES:
1. PARKING BUMPER (IF REQUIRED) MUST BE INSTALLED BEFORE C.O.
2. 5/8" TYPE "X' GYP. BOARD REQUIRED ON CEILING OF GARAGE WHERE HABITAL SPACE ISABOVE PER FBC R302.6.
3. HVAC PENETRATING RATED ASSEMBLIES TO COMPLY WITH FBC R302.5.
4. UNDER STAIR PROTECTION TO COMPLY WITH FBC R302.7 (IF ACCESSIBLE).
HANDRAIL NOTE:
DEPENDING ON FIELD CONDITIONS, DIMENSIONS MAY VARY BUT MUST COMPLY WITH FLORIDA BUILDING
CODES R311.5.6-R311.5.6.3 FOR HANDRAIL HEIGHT CONTINUITY AND SIZE.
*HEIGHT: MUST BE BETWEEN 34-38" MEASURED VERTICALLY FROM SLOPED PLANE.
*CONTINUITY: HANDRAIL MUST BE CONTINUOUS THROUGH FULL LENGTH OF FLIGHT FROM POINT
DIRECTLY ABOVE HIGHEST RISER TO POINT DIRECTLY ABOVE LOWEST RISER. HANDRAIL ENDS SHOULD
TERMINATE IN NEWEL POSTS OR SAFETY TERMINAL OR RETURN TO WALL. HANDRAILS SHALL BEALLOWED TO BE INTERRUPTED BY NEWEL POSTS.
*SIZE: SHALL HAVE OUTSIDE DIAMETER BETWEEN 1-1/4"-2" IF CIRCULAR. SHALL HAVE BETWEEN 4-6"
PERIMETER IF NOT CIRCULAR.
STAIR NOTE:
DEPENDING ON FIELD CONDITIONS, DIMENSIONS MAY VARY BUT MUST COMPLY WITH FLORIDA BUILDING
CODES R311.5.1-R311.5.5 FOR TREAD DEPTH, RISER HEIGHTS AND STAIR WIDTHS.
*RISERS: 7-3/4" MAXIMUM WITH NO MORE THAN 3/8" DIFFERENCE BETWEEN HIGHEST AND LOWESTRISER.
TREADS: 10" MINIMUM DEPTH WITH NO MORE THAN 3/8" DIFFERENCE BETWEEN LONGEST AND
SHORTEST TREAD. THE SUM OF 2 TREADS AND 1 RISER TO BE NOT LESS THAN 24" AND NOT MORE THAN
25".*WIDTH: 36" MINIMUM CLEAR WIDTH ABOVE HANDRAIL AND 31-1/2" BELOW HANDRAIL.DateSheet
Job
Scale
DateNo.RevisionsBy7654321AMERICAN CLASSIC HOMES, LLC4550 St. Augustine RoadJacksonville, FL 32207(904) 351-0308COPYRIGHT WARNING!CTHESE PLANS AND SPECIFICATIONS ARE THE SOLE ANDEXCLUSIVE PROPERTY OF AMERICAN CLASSIC HOMES. THEUSE OF THESE PLANS AND SPECIFICATIONS OR ANYPORTION THEREOF OR REPRODUCTION OF SAME WITHOUTTHE PRIOR WRITTEN CONSENT OF AMERICAN CLASSICHOMES IS STRICTLY PROHIBITED AND WILL BE PROSECUTEDTO THE FULLEST EXTENT OF THE LAW1549D-8/8
04-27-21
AS SHOWNPROPOSED 2 STORY DUPLEXJACKSONVILLE, FLDETAIL SHEETA3.1
1505-1507 Richardson Ln
By Toni Gindlesperger at 5:01 pm, Jun 09, 2021