1470 Ocean Blvd RES23-0006 new SFH 5 of 6 Pages 1 - 8 Saas Lot 5 BLK 59 Mandalay Architect draw. 11-29-22_NOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19A1Plat Book 10, Page 11Lot 5, Block 59, MandalaySaas ResidenceAtlantic Beach,Duval County, FloridaBy Jennifer Johnston at 12:05 pm, Jan 13, 2023RES23-0006By Mike Jones at 1:31 pm, Jan 25, 2023
NOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19A2 By Jennifer Johnston at 12:05 pm, Jan 13, 2023RES23-0006
ALL STUCCO APPLICATIONS SHALL COMPLY WITH THE RECOMMENDATIONS OF THEPORTLAND CEMENT ASSOCIATION, ASTM STANDARDS - C926-98a, C926, A2.2.2, - PROVIDE AN EXTERIOR SEALANT.- WHEN REQUIRED BY ASTM C926, SECTION 5.2.2; AN EXTERIOR BONDING AGENT, CONFORMING TO ASTM C 932, SHALL BE USED ON ALLMETHODS FOR BONDING.MASONRY SURFACES. IN LIEU OF A BONDING AGENT, A DASH COAT, ROUGHING THE SURFACE, OR METAL LATH ARE ALSO ACCEPTABLEOVER BOTH MASONRY AND CAST CONCRETE.TWO-COAT SYSTEMS OVER MASONRY CONSIST OF: FIRST COAT = 3/8 INCH THICK AND FINISH COAT = 1/8 INCH THICK;OR OVER CAST CONCRETE CONSIST OF: FIRST COAT = 1/4 INCH THICK AND FINISH COAT = 1/8 INCH THICK.- CONVENTIONAL STUCCO OVER MASONRY SURFACES MAY BE APPLIED WITH TWO OR THREE COATS.THREE - COAT SYSTEMS CONSIST OF: FIRST COAT = 1/4 INCH THICK, SECOND COAT = 1/4 INCH THICK, AND FINISH COAT = 1/8 INCH THICKC932-03, C1063-03, C1328-00, AND THE FOLLOWING;STUCCO ON MASONRYNOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19A3 By Jennifer Johnston at 12:05 pm, Jan 13, 2023RES23-0006
ALL STUCCO APPLICATIONS SHALL COMPLY WITH THE RECOMMENDATIONS OF THEPORTLAND CEMENT ASSOCIATION, ASTM STANDARDS - C926-98a, C926, A2.2.2, - PROVIDE AN EXTERIOR SEALANT.- WHEN REQUIRED BY ASTM C926, SECTION 5.2.2; AN EXTERIOR BONDING AGENT, CONFORMING TO ASTM C 932, SHALL BE USED ON ALLMETHODS FOR BONDING.MASONRY SURFACES. IN LIEU OF A BONDING AGENT, A DASH COAT, ROUGHING THE SURFACE, OR METAL LATH ARE ALSO ACCEPTABLEOVER BOTH MASONRY AND CAST CONCRETE.TWO-COAT SYSTEMS OVER MASONRY CONSIST OF: FIRST COAT = 3/8 INCH THICK AND FINISH COAT = 1/8 INCH THICK;OR OVER CAST CONCRETE CONSIST OF: FIRST COAT = 1/4 INCH THICK AND FINISH COAT = 1/8 INCH THICK.- CONVENTIONAL STUCCO OVER MASONRY SURFACES MAY BE APPLIED WITH TWO OR THREE COATS.THREE - COAT SYSTEMS CONSIST OF: FIRST COAT = 1/4 INCH THICK, SECOND COAT = 1/4 INCH THICK, AND FINISH COAT = 1/8 INCH THICKC932-03, C1063-03, C1328-00, AND THE FOLLOWING;STUCCO ON MASONRYNOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19A4 By Jennifer Johnston at 12:05 pm, Jan 13, 2023RES23-0006
ALL STUCCO APPLICATIONS SHALL COMPLY WITH THE RECOMMENDATIONS OF THEPORTLAND CEMENT ASSOCIATION, ASTM STANDARDS - C926-98a, C926, A2.2.2, - PROVIDE AN EXTERIOR SEALANT.- WHEN REQUIRED BY ASTM C926, SECTION 5.2.2; AN EXTERIOR BONDING AGENT, CONFORMING TO ASTM C 932, SHALL BE USED ON ALLMETHODS FOR BONDING.MASONRY SURFACES. IN LIEU OF A BONDING AGENT, A DASH COAT, ROUGHING THE SURFACE, OR METAL LATH ARE ALSO ACCEPTABLEOVER BOTH MASONRY AND CAST CONCRETE.TWO-COAT SYSTEMS OVER MASONRY CONSIST OF: FIRST COAT = 3/8 INCH THICK AND FINISH COAT = 1/8 INCH THICK;OR OVER CAST CONCRETE CONSIST OF: FIRST COAT = 1/4 INCH THICK AND FINISH COAT = 1/8 INCH THICK.- CONVENTIONAL STUCCO OVER MASONRY SURFACES MAY BE APPLIED WITH TWO OR THREE COATS.THREE - COAT SYSTEMS CONSIST OF: FIRST COAT = 1/4 INCH THICK, SECOND COAT = 1/4 INCH THICK, AND FINISH COAT = 1/8 INCH THICKC932-03, C1063-03, C1328-00, AND THE FOLLOWING;STUCCO ON MASONRYNOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19A5 By Jennifer Johnston at 12:05 pm, Jan 13, 2023RES23-0006
NOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19WALL LEGENDCMU WALLFRAME WALLMIN. DOOR RETURN6" MIN.R302.12 Draftstopping.In combustible construction where there is usable space both above and below the concealed space of a floor/ceiling assembly,draftstops shall be installed so that the area of the concealed space does not exceed 1,000 square feet (92.9 m2). Draftstoppingshall divide the concealed space into approximately equal areas. Where the assembly is enclosed by a floor membrane above and a ceiling membrane below, draftstopping shall be provided in floor/ceiling assemblies under the following circumstances:1. Ceiling is suspended under the floor framing.2. Floor framing is constructed of truss-type open-web or perforated members. R302.12.1 Materials. Draftstopping materials shall not be less than 1/2-inch (12.7 mm) gypsum board, 3/8-inch (9.5 mm) wood structural panels or other approved materials adequately supported. Draftstopping shall be installed parallel to the floor framing members unless otherwise approved by the building official. The integrity of the draftstops shall be maintained.DRAFTSTOPPING OPEN WEB FLOOR SYSTEMDRAFTSTOPPING SUSPENDED CEILINGSUBFLOORTRUSSDRAFTSTOP MATERIALDRYWALLSUBFLOORFLOOR JOISTDRAFTSTOP MATERIALA6By Jennifer Johnston at 12:06 pm, Jan 13, 2023RES23-0006
NOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19 R302.12 Draftstopping.In combustible construction where there is usable space both above and below the concealed space of a floor/ceiling assembly,draftstops shall be installed so that the area of the concealed space does not exceed 1,000 square feet (92.9 m2). Draftstoppingshall divide the concealed space into approximately equal areas. Where the assembly is enclosed by a floor membrane above and a ceiling membrane below, draftstopping shall be provided in floor/ceiling assemblies under the following circumstances:1. Ceiling is suspended under the floor framing.2. Floor framing is constructed of truss-type open-web or perforated members. R302.12.1 Materials. Draftstopping materials shall not be less than 1/2-inch (12.7 mm) gypsum board, 3/8-inch (9.5 mm) wood structural panels or other approved materials adequately supported. Draftstopping shall be installed parallel to the floor framing members unless otherwise approved by the building official. The integrity of the draftstops shall be maintained.DRAFTSTOPPING OPEN WEB FLOOR SYSTEMDRAFTSTOPPING SUSPENDED CEILINGSUBFLOORTRUSSDRAFTSTOP MATERIALDRYWALLSUBFLOORFLOOR JOISTDRAFTSTOP MATERIALWALL LEGENDFRAME WALLMIN. DOOR RETURN6" MIN.A7By Jennifer Johnston at 12:06 pm, Jan 13, 2023RES23-0006
NOVEMBER 28
,
2022
ISSUED
FOR
CONSTRUCT
IONCONSTRUCTION
SET
Plat Book 10, Page 11
Lot 5, Block 59, Mandalay
Saas Residence
Atlantic Beach,
Duval County, Florida19WALL LEGENDFRAME WALLMIN. DOOR RETURN6" MIN.A8By Jennifer Johnston at 12:04 pm, Jan 13, 2023RES23-0006