1025 EAST COAST DR RES24-0032 B5_Windows_FL31115_R2_II_RWD0002_Rev0_8500F_ssRJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueRENAISSANCE WINDOWS AND DOORS
SERIES 9IN</ )I;ED WINDOW
INS7A//A7ION ANC+ORA*E DE7AI/S
N.T.S.GENERAL NOTES, INSTALLATION NOTES & TABLE OF CONTENTS1GENERAL NOTES:
1.THIS PRODUCT HAS BEEN TESTED, EVALUATED AND DESIGNED TO THE CURRENT EDITION OF THE
FLORIDA BUILDING CODE. TESTING WAS CONDUCTED IN ACCORDANCE WITH AAMA/NWWDA 101/I.S.2-97
AND AAMA/WDMA/CSA 101/I.S.2/A440-05.
2.THE PRODUCT DETAILS CONTAINED HEREIN ARE BASED UPON SIGNED AND SEALED TEST REPORT
NO.77856.01-801-44 AND 02-46046.01 AND ASSOCIATED LABORATORY DRAWINGS BY ARCHITECTURAL
TESTING, INC.
3.THIS PRODUCT EVALUATION DOCUMENT IS NOT FOR USE IN THE HIGH VELOCITY HURRICANE ZONE
(HVHZ).
4.ADEQUACY OF THE EXISTING STRUCTURAL CONCRETE / MASONRY AND 2X FRAMING FRAMING
SUBSTRATES AS A MAIN WIND FORCE RESISTING SYSTEM CAPABLE OF WITHSTANDING AND
TRANSFERRING APPLIED PRODUCT LOADS TO THE FOUNDATION IS THE RESPONSIBILITY OF THE
LICENSED PROFESSIONAL ENGINEER OR REGISTERED ARCHITECT ACTING AS THE DESIGN
PROFESSIONAL OF RECORD FOR THE PROJECT OF INSTALLATION.
5.1X AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED AND ANCHORED TO PROPERLY TRANSFER ALL
LOADS TO THE STRUCTURE. BUCK DESIGN AND INSTALLATION IS THE RESPONSIBILITY OF THE
LICENSED PROFESSIONAL ENGINEER OR REGISTERED ARCHITECT ACTING AS THE DESIGN
PROFESSIONAL OF RECORD FOR THE PROJECT OF INSTALLATION.
6.WHEN INSTALLED IN LOCATIONS WHERE WINDBORNE DEBRIS PROTECTION REQUIREMENTS EXIST,THIS
PRODUCT REQUIRES OPENING PROTECTION IN ACCORDANCE WITH THE CURRENT EDITION OF THE
FLORIDA BUILDING CODE USING AN APPROVED IMPACT PROTECTION DEVICE.
7.SITE CONDITIONS NOT COVERED IN THIS PRODUCT EVALUATION DOCUMENT ARE SUBJECT TO
ADDITIONAL ENGINEERING ANALYSIS BY A LICENSED PROFESSIONAL ENGINEER OR REGISTERED
ARCHITECT AS REQUIRED BY THE AUTHORITY HAVING JURISDICTION.
8.WINDOW FRAME MATERIAL: VINYL (PVC).
9.GLASS MEETS THE REQUIREMENTS OF ASTM E1300-09a.
10.DESIGNATION "O" STANDS FOR FIXED LITE.
11.THESE DRAWINGS CERTIFY THE WINDOW INSTALLATION ONLY. WATER PROOFING OF THE
INSTALLED WINDOW IS NOT PART OF THIS INSTALLATION CERTIFICATION. THAT RESPONSIBILITY SHALL
BE THAT OF THE MANUFACTURER AND/OR THE INSTALLER.
INSTALLATION NOTES:
1.PRODUCT ANCHORS SHALL BE AS DESIGNATED AND LOCATED AS SHOWN IN THIS PRODUCT EVALUATION DOCUMENT.
ANCHOR EMBEDMENT AND EDGE DISTANCE EXCLUDE WALL FINISHES, INCLUDING BUT NOT LIMITED TO STUCCO, FOAM,
BRICK VENEER AND SIDING.
2.SEE INSTALLATION ANCHOR SCHEDULE ON SHEET 2 FOR TYPE AND GRADE OF ANCHOR, AND/OR MANUFACTURER'S
ANCHOR SPECIFICATIONS, INCLUDING MINIMUM NOMINAL SIZE, MINIMUM EMBEDMENT INTO SUBSTRATE AND MINIMUM
EDGE DISTANCES.
2.1.EDGE DISTANCES SHALL BE MEASURED FROM CENTERLINE OF ANCHOR TO EDGE OF STRUCTURAL SUBSTRATE EITHER
TO THE INTERIOR OR EXTERIOR OF THE FENESTRATION PRODUCT.
2.2.MINIMUM EMBEDMENT SHALL BE BASED ON PENETRATION INTO MAIN WIND FORCE RESISTING SYSTEM SUBSTRATE.
3.SEE SHEETS 5 THROUGH 7 FOR SPECIFIC ANCHOR INSTALLATION DETAILS.
4.ONE (1) INSTALLATION ANCHOR IS REQUIRED AT EACH ANCHOR LOCATION SHOWN.
5.ANCHOR QUANTITIES AND SPACING / EMBEDMENT AND EDGE DISTANCE
5.1.THE NUMBER OF INSTALLATION ANCHORS IS BASED ON THE MAXIMUM END DISTANCE (ED) AND THE MAXIMUM ON
CENTER (O.C.) SPACING PLACEMENT OF ANCHORS IN ACCORDANCE WITH ELEVATIONS ON SHEETS 3 AND 4.
5.2.END DISTANCES AND O.C. SPACINGS LESS THAN THAT SHOWN IN THE ELEVATIONS ON SHEETS 3 AND 4 ARE
ACCEPTABLE.
5.3.FOR WINDOW SIZES SMALLER THAN THOSE SHOWN, ANCHOR QUANTITIES CAN BE REDUCED WHILE MAINTAINING EDGE
DISTANCE AND O.C. SPACING REQUIREMENTS.
5.4.ANCHOR QUANTITIES AND SPACINGS SHOWN ARE BASED ON THE LOWER OF ANCHOR SPACING USED IN TESTING OR
REQUIRED BY LOADING AT DESIGN PRESSURE.
5.5.SEE EMBEDMENT AND EDGE DISTANCE DESCRIPTION ON SHEET 2.
6.MAXIMUM ALLOWABLE SHIM THICKNESS IS 1/4 INCH. SHIM WHERE SPACE OF 1/16 INCH OR GREATER OCCURS. SHIM(S)
SHALL BE CONSTRUCTED OF WOOD COMPOSITE, HIGH DENSITY PLASTIC OR SIMILAR LOAD BEARING MATERIAL.
7.FOR CONCRETE BLOCK APPLICATIONS DO NOT INSTALL INSTALLATION ANCHORS INTO MORTAR JOINTS.
8.INSTALLATION ANCHORS SHALL BE INSTALLED IN ACCORDANCE WITH ANCHOR MANUFACTURER'S INSTALLATION
INSTRUCTIONS AND ANCHORS SHALL NOT BE USED IN SUBSTRATES WITH STRENGTHS LESS THAN THE MINIMUM STRENGTH
SPECIFIED IN THE INSTALLATION ANCHOR SCHEDULE ON SHEET 2.
TABLE OF CONTENTS
SHEET SHEET DESCRIPTION
1 GENERAL NOTES, INSTALLATION NOTES, TABLE OF CONTENTS
2 ANCHOR SCHEDULE - EMBEDMENT AND EDGE DISTANCE
3 NOMINAL 60" x 78" WINDOW ELEVATION & ANCHORING LAYOUT
4 NOMINAL 48" x 96" WINDOW ELEVATION & ANCHORING LAYOUT
5 CROSS SECTIONS - NAILING FIN INSTALLATION
6 CROSS SECTIONS - THRU FRAME INSTALLATION
7 CROSS SECTIONS - SNAP-ON FLANGE THRU FRAME INSTALLATION
8 GLAZING DETAIL AND GLAZING NOTES /BILL OR MATERIALS
PERFORMANCE RATING
MAXIMUM WINDOW SIZE ELEVATION GLAZING DETAIL
(SEE SHEET 8)DESIGN PRESSURE (PSF)IMPACT RATING
NOMINAL 48" x 96"
(47-5/8" x 95-5/8")
SHEET 4
(NOTE 1)A +/- 47
NONE
SEE NOTE 6
NOMINAL 48" x 93"
(47-5/8" x 92-5/8")
SHEET 4
(NOTE 2)A +/- 50
NOMINAL 60" x 78"
(59-3/4" x 77-3/4")
SHEET 3
(NOTE 1)B +/- 29.7
NOMINAL 60" x 78"
(59-3/4" x 77-3/4")
SHEET 3
(NOTE 3)A +/-50
NOTES:
1) AS-TESTED WINDOW SIZE AND GLAZING. DESIGN PRESSURES LIMITED BY GLAZING DETAIL.
2) REDUCED HEIGHT WINDOW SIZE TO OBTAIN TESTED DESIGN PRESSURE WITH TESTED GLAZING. ANCHOR
QUANTITIES SHOWN ON SHEET 4 WILL BE MAINTAINED.
3) AS-TESTED WINDOW SIZE WITH ENHANCED GLAZING (UPSIZED FROM TEST) TO OBTAIN TESTED DESIGN PRESSURE.
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueEMBEDMENT AND EDGE DISTANCE
NAILING FIN FRAME INSTALLATION
EMBEDMENT AND EDGE DISTANCE
THROUGH-FRAME INSTALLATION
EMBEDMENT AND EDGE DISTANCE
SNAP-ON FLANGE THROUGH-FRAME INSTALLATION N.T.S.ANCHOR SCHEDULE - EMBEDMENT & EDGE DISTANCE2
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueOC
5
C
6
C
7
B
5
B
6
B
7
A
5
A
6
A
7
SERIES 8500 VINYL FIXED WINDOW
EXTERIOR VIEW (60" X 78" NOMINAL SIZE SHOWN)N.T.S.NOMINAL 60" x 78" WINDOW ELEVATION & ANCHORING LAYOUT3
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueO
B
5
B
6
B
7
C
5
C
6
C
7
A
5
A
6
A
7
SERIES 8500 VINYL FIXED WINDOW
EXTERIOR VIEW (48" X 96" NOMINAL SIZE SHOWN)N.T.S.NOMINAL 48" x 96" WINDOW ELEVATION & ANCHORING LAYOUT4
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueSILL CROSS SECTION
NAILING FIN FRAME INSTALLATION5
A
JAMB CROSS SECTION
NAILING FIN FRAME INSTALLATION5
C
EXTERIOR
INTERIOR
HEAD CROSS SECTION
NAILING FIN FRAME INSTALLATION5
B
EXTERIOR INTERIOR
EXTERIOR INTERIOR N.T.S.CROSS SECTIONS - NAILING FIN INSTALLATION5
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueEXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
SILL CROSS SECTION
THROUGH-FRAME INSTALLATION6
A
JAMB CROSS SECTION
THROUGH-FRAME INSTALLATION6
C
HEAD CROSS SECTION
THROUGH-FRAME INSTALLATION6
B
N.T.S.CROSS SECTIONS - THRU FRAME INSTALLATION6
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueSILL CROSS SECTION
SNAP-ON FLANGE
THROUGH-FRAME INSTALLATION7
A
EXTERIOR
INTERIOR
HEAD CROSS SECTION
SNAP-ON FLANGE
THROUGH-FRAME INSTALLATION7
A
JAMB CROSS SECTION
SNAP-ON FLANGE
THROUGH-FRAME INSTALLATION7
AEXTERIOR
EXTERIOR INTERIOR
INTERIOR N.T.S.CROSS SECTIONS - SNAP-ON FLANGE THRU FRAME INSTALL.7
RJA8OF12/5/19RWD0002SERIES 8500 VINYL FIXED WINDOWPTC PRODUCT DESIGN GROUP, LLCPO BOX 520775LONGWOOD, FLORIDA 32752FBPE C.A. NO. 25935TITLE:DRAWN BY:SCALE:REV:DATE:DRAWING NO:SHEET:RENAISSANCE WINDOWS AND DOORS13340 INTERNATIONAL PARKWAYJACKSONVILLE, FL 32218Robert J. Amoruso, P.E.
Florida P.E. No. 49752 Phone: 321.690.1788Fax: 321.690.1789Email: info@ptc-corp.comREVDESCRIPTIONDATEBYPROJECT # 419-0901First IssueGLAZING DETAIL A GLAZING DETAIL B
NOTES:
1.A MINIMUM OF TWO (2) NEOPRENE SETTING BLOCKS WITH 70 TO 90 SHORE A DUROMETER HARDNESS ARE
REQUIRED AT BOTTOM (SILL) OF GLAZING LITES MORE THAN 3 FEET IN WIDTH.
2.AS-TESTED IGU SYSTEM SHOWN. OTHER SUBSTITUTES ARE ALLOW WHILE MAINTAINING INDIVIDUAL LITE
THICKNESS AND TEMPER. SEE SHEET 1 FOR DETAILS RELATED TO WINDOW SIZE / GLAZING DETAIL /
DESIGN PRESSURE.N.T.S.GLAZING DETAILS AND NOTES / BILL OF MATERIALS8