331 2ND ST PPI24-0001 FL41795 InstallationSIZE CHART, PANEL SIZE CHART & GENERAL NOTESSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BTABLE OF CONTENTS
SHEET SHEET DESCRIPTION
1 SIZE CHART, PANEL SIZE CHART & GENERAL NOTES
2-3 TABLE 1 & TABLE 2
4 CONFIGURATIONS & ELEVATIONS
5 HORIZONTAL SECTION DETAILS
6 VERTICAL SECTION DETAILS
7-24 ANCHOR LAYOUTS
25 P-HOOK ANCHOR LAYOUT DETAILS & TABLE 3
26 GLAZING DETAILS & SPLICE DETAILS
SIZE CHART
OVERALL FRAME
MAX. SIZE PERFORMANCE
RATING
DESIGN
PRESSURE
Min. Sill
Riser
INSTALLATION
METHODWIDTH HEIGHT
239"96"
LC-PG35
+35/-35 PSF
3/4"NAIL FIN
OR
THROUGH
FRAME
353"96"+35/-35 PSF
281" 120"+35/-35 PSF
353" 96"LC-PG50 +50/-50 PSF 1-3/4"281"120"+50/-50 PSF
FL#:
PANEL SIZE CHART
PANEL
CALL SIZE
PANEL MAX.
SIZE
MAX D.L.O.GLAZING
DETAIL TYPEWIDTH HEIGHT
3-0 8-0 37-1/8" x 93-1/16"28-1/8" 84-1/16"1, 2 or 4
3-0 10-0 37-1/8" x 117-1/8"28-1/8" 108-1/8" 3 or 4
4-0 8-0 49-1/8" x 93-1/16"40-1/8" 84-1/16" 2 or 4
4-0 10-0 49-1/8" X 117-1/8"40-1/8" 108-1/8" 3 or 4
5-0 8-0 61-1/8" x 93-1/16"52-1/8"84-1/16" 3 or 4
SIMONTON WINDOWS MAXVIEW Multi-Slide Patio Door (NON-IMPACT)
NOTES:
1. This installation has been evaluated for use in locations adhering to the
Florida Building Code outside the HVHZ, and where pressure requirements
as determined by ASCE 7 Minimum Design Loads for Buildings and Other
Structures do not exceed the design pressure ratings herein.
2. When used in areas requiring impact protection, this product REQUIRES the
use of approved impact protective devices (shutters).
3. Anchor type, size, spacing, embedment, and edge distance shall be as
specified in these drawings. Use appropriate anchorage from Table 1 and
Table 2 according to substrate type. A minimum center-to-center spacing
shall be maintained between all installation fasteners in any direction.
4. Anchor embedment to substrate shall be beyond wall dressing or stucco.
For masonry openings with wood bucks less than 1-1/2" thick, embedment
shall be beyond wood bucks, if used, and into masonry substrate. Wood
bucks with masonry are optional.
5. Wood, metal, or masonry openings, bucks, and buck fasteners, by others,
shall be properly designed and installed by others to transfer
superimposed loads to the structure. Adequacy of the structure to received
these loads shall be verified by the contractor or Authority Having
Jurisdiction (AHJ).
6. It is the responsibility of the architect or engineer of record or as
approved by the AHJ to select Simonton products to meet all applicable
local laws, building codes, ordinances, or other safety requirements for
each installation.
7. Shims are required where gaps of greater than 1/16" exist between opening
and frame. Max. shim stack is 1/4". Shims shall be load-bearing and capable
of transferring loads to the substrate.
8. Sealing and flashing strategies for overall water infiltration resistance
of the installed product shall be the responsibility of others using ASTM E
2112 and is not addressed by this document.
9. Installed glazing shall comply with ASTM E 1300.
10. All fasteners penetrating into pressure treated wood shall be capable of
preventing corrosion due to reaction with pressure treatment chemicals.
Any dissimilar materials that come into contact shall be protected to
prevent reactions in accordance with code requirements.
11.
12.
13.
A wind load duration factor Cd = 1.6 was used for the analysis of wood
screws only.
Products shall be constructed as specified in test reports
11835.06/10/11/12/13/14/15/17/18/19/22-106-11-r0, 11835.02/16-106-11-r1,
11835.05/07-106-11-r2 and 11835.03-106-12-r1 by Molimo Architectural
Product Testing.
Pocket wall/cavity is not part of this approval and reviewed by the
authority having jurisdiction (AHJ).
14. Use a backer rod on all joints >3/4" deep and/or wider than 1/4". Finished
caulk joint should be a minimum of 3/8" deep.MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
1-FL
Lucas Turner
2023.12.19
15:17:47
-06'00'
TABLE 1SHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:2 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BNOTES: -ALL SCREWS SHALL BE PAN OR HEX WASHER HEAD.
-PRE-DRILLING FOR ANCHORS INTO WOOD IS RECOMMENDED.
-SEE SHEET 25 FOR P-HOOK DETAILS.
-CONCRETE/MASONRY SHALL NOT BE CRACKED.
PERFORMANCE GRADE LC-PG35
TABLE 1: INSTALLATION FASTENERS TABLE
PANEL WIDTH
UP TO 3-0 10-0 MAX.UP TO 4-0 10-0 MAX. UP TO 5-0 8-0 MAX.
ID FRAME
LOCATION SUBSTRATE TYPE ANCHOR TYPE MIN. EDGE
DISTANCE
MIN.
EMBED.
MIN. ON
CENTER
SPACING
HEAD & SILL
CLUSTERS
QUANTITY
JAMB
O.C.
SPACING
HEAD & SILL
CLUSTERS
QUANTITY
JAMB
O.C.
SPACING
HEAD & SILL
CLUSTERS
QUANTITY
JAMB
O.C.
SPACING
A HEAD/SILL/JAMB CONCRETE (2 KSI MIN.) 1/4" ITW TAPCON w/ADVANCED THREADFORM
TECHNOLOGY COATED CARBON STEEL 1-1/2" 1-3/4" 4" 3 16-3/4" 3 16-3/4" 3 16-3/4"
B JAMBS ONLY HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
1/4" ITW TAPCON w/ADVANCED THREADFORM
TECHNOLOGY COATED CARBON STEEL 2" 1"4" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
C HEAD/SILL/JAMB CONCRETE (3.05 KSI MIN.) 1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 1" 1-3/8" 4" 3 16-3/4"4 16-3/4"4 16-3/4"
D HEAD/SILL/JAMB CONCRETE (3.05 KSI MIN.) 1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 2-1/2" 1-3/8" 4" 3 16-3/4"3 16-3/4"3 16-3/4"
E JAMBS ONLY HOLLOW CMU
(ASTM C-90)
1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 1" 1-1/4" 3" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
F JAMBS ONLY HOLLOW CMU
(ASTM C-90)
1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 2-1/2" 1-1/4" 3" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
G JAMBS ONLY GROUT-FILLED CMU
(ASTM C-90)
1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 1"1-1/4" 4" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
H HEAD/SILL/JAMB CONCRETE (3 KSI MIN.) 1/4" HILTI KWIK-CON+,
COATED CARBON STEEL 2-1/2" 1" 2" 3 16-3/4"3 16-3/4"3 16-3/4"
I JAMBS ONLY HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
1/4" HILTI KWIK-CON+,
COATED CARBON STEEL 2-1/2" 1" 4" N/A 16-3/4"N/A 16-3/4"N/A 16-3/4"
J HEAD/SILL/JAMB CONCRETE (2.22 KSI MIN.) 1/4" DEWALT AGGRE-GATOR, 300 STAINLESS
STEEL 1-1/2" 1-3/8" 3" 3 16-3/4" 3 16-3/4" 3 16-3/4"
K JAMBS ONLY HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
1/4" DEWALT AGGRE-GATOR, 300 STAINLESS
STEEL 2"1-1/4" 3" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
L HEAD/SILL/JAMB 2X MIN. SPRUCE-PINE-FIR WOOD
(G>=0.42) #12 GRADE 5 WOOD SCREW 3/4" 1-1/2" 3" 3 16-3/4" 4 16-3/4" 4 16-3/4"
M HEAD/SILL/JAMB 2X MIN. SOUTHERN PINE WOOD
(G>=0.55) #12 GRADE 5 WOOD SCREW 3/4" 1-1/2" 3" 3 16-3/4"4 16-3/4"4 16-3/4"
N HEAD/SILL/JAMB 2X MIN. SPRUCE-PINE-FIR WOOD
(G>=0.42)
1/4" MASONARY FASTENERS AS LISTED IN
THIS TABLE 1" 1-1/2" 3" 3 16-3/4"4 16-3/4"4 16-3/4"
O HEAD/SILL/JAMB 2X MIN. SOUTHERN PINE WOOD
(G>=0.55)
1/4" MASONARY FASTENERS AS LISTED IN
THIS TABLE 1" 1-1/2" 3" 3 16-3/4" 4 16-3/4" 4 16-3/4"
P HEAD/SILL/JAMB 16 GAUGE (0.060"), MIN. STEEL
STUD, 33 KSI YIELD MIN.
#12-14 ITW TEKS,DEWALT DRIL-FLEX, OR
HILTI KWIK-FLEX SELF-DRILLING SCREW 1/2"FULL PLUS 3
THREADS MIN.3" 3 16-3/4" 3 16-3/4" 3 16-3/4"
Q HEAD/SILL/JAMB 1/8" ALUM. 6063-T5 MIN. or
1/8" STEEL 36 KSI MIN.
#12-14 GRADE 5 SELF-TAPPING/DRILLING
SCREW 1/2"FULL PLUS 3
THREADS MIN.3" 3 16-3/4" 3 16-3/4" 3 16-3/4"
FL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
TABLE 2SHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:3 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BPERFORMANCE GRADE LC-PG50
TABLE 2: INSTALLATION FASTENERS TABLE
PANEL WIDTH
UP TO 3-0 10-0 MAX.UP TO 4-0 10-0 MAX. UP TO 5-0 8-0 MAX.
ID FRAME
LOCATION SUBSTRATE TYPE ANCHOR TYPE MIN. EDGE
DISTANCE
MIN.
EMBED.
MIN. ON
CENTER
SPACING
HEAD & SILL
CLUSTERS
QUANTITY
JAMB
O.C.
SPACING
HEAD & SILL
CLUSTERS
QUANTITY
JAMB
O.C.
SPACING
HEAD & SILL
CLUSTERS
QUANTITY
JAMB
O.C.
SPACING
A HEAD/SILL/JAMB CONCRETE (2 KSI MIN.) 1/4" ITW TAPCON w/ADVANCED THREADFORM
TECHNOLOGY COATED CARBON STEEL 1-1/2" 1-3/4" 4" 3 16-3/4" 3 16-3/4" 3 16-3/4"
B JAMBS ONLY HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
1/4" ITW TAPCON w/ADVANCED THREADFORM
TECHNOLOGY COATED CARBON STEEL 2"1" 4" N/A 15-1/4" N/A 15-1/4" N/A 15-1/4"
C HEAD/SILL/JAMB CONCRETE (3.05 KSI MIN.) 1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 1" 1-3/8" 4" 4 15-1/4" 5 15-1/4" 5 15-1/4"
D HEAD/SILL/JAMB CONCRETE (3.05 KSI MIN.) 1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 2-1/2" 1-3/8" 4" 3 16-3/4"3 16-3/4"3 16-3/4"
E JAMBS ONLY HOLLOW CMU
(ASTM C-90)
1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 1" 1-1/4" 3" N/A 15-1/4"N/A 15-1/4"N/A 15-1/4"
F JAMBS ONLY HOLLOW CMU
(ASTM C-90)
1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 2-1/2" 1-1/4" 3" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
G JAMBS ONLY GROUT-FILLED CMU
(ASTM C-90)
1/4" DEWALT ULTRACON+,
COATED CARBON STEEL 1" 1-1/4" 4" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
H HEAD/SILL/JAMB CONCRETE (3 KSI MIN.) 1/4" HILTI KWIK-CON+,
COATED CARBON STEEL 2-1/2" 1" 2" 3 16-3/4"3 16-3/4"3 16-3/4"
I JAMBS ONLY HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
1/4" HILTI KWIK-CON+,
COATED CARBON STEEL 2-1/2" 1" 4" N/A 16-3/4"N/A 16-3/4"N/A 16-3/4"
J HEAD/SILL/JAMB CONCRETE (2.22 KSI MIN.) 1/4" DEWALT AGGRE-GATOR, 300 STAINLESS
STEEL 1-1/2" 1-3/8" 3" 3 16-3/4" 3 16-3/4" 3 16-3/4"
K JAMBS ONLY HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
1/4" DEWALT AGGRE-GATOR, 300 STAINLESS
STEEL 2"1-1/4" 3" N/A 16-3/4" N/A 16-3/4" N/A 16-3/4"
L HEAD/SILL/JAMB 2X MIN. SPRUCE-PINE-FIR WOOD
(G>=0.42) #12 GRADE 5 WOOD SCREW 3/4" 1-1/2" 3" 4 16-1/2" 5 16-1/2" 5 16-1/2"
M HEAD/SILL/JAMB 2X MIN. SOUTHERN PINE WOOD
(G>=0.55) #12 GRADE 5 WOOD SCREW 3/4"1-1/2"3" 4 16-1/2" 5 16-1/2" 5 16-1/2"
N HEAD/SILL/JAMB 2X MIN. SPRUCE-PINE-FIR WOOD
(G>=0.42)
1/4" MASONARY FASTENERS AS LISTED IN
THIS TABLE 1" 1-1/2" 3" 4 16-1/2" 5 16-1/2" 5 16-1/2"
O HEAD/SILL/JAMB 2X MIN. SOUTHERN PINE WOOD
(G>=0.55)
1/4" MASONARY FASTENERS AS LISTED IN
THIS TABLE 1" 1-1/2" 3" 4 16-1/2" 5 16-1/2" 5 16-1/2"
P HEAD/SILL/JAMB 16 GAUGE (0.060"), MIN. STEEL
STUD, 33 KSI YIELD MIN.
#12-14 ITW TEKS,DEWALT DRIL-FLEX, OR
HILTI KWIK-FLEX SELF-DRILLING SCREW 1/2"FULL PLUS 3
THREADS MIN.3" 3 16-3/4" 3 16-3/4" 3 16-3/4"
Q HEAD/SILL/JAMB 1/8" ALUM. 6063-T5 MIN. or
1/8" STEEL 36 KSI MIN.
#12-14 GRADE 5 SELF-TAPPING/DRILLING
SCREW 1/2"FULL PLUS 3
THREADS MIN.3" 3 16-3/4" 3 16-3/4" 3 16-3/4"
FL#:
NOTES: -ALL SCREWS SHALL BE PAN OR HEX WASHER HEAD.
-PRE-DRILLING FOR ANCHORS INTO WOOD IS RECOMMENDED.
-SEE SHEET 25 FOR P-HOOK DETAILS.
-CONCRETE/MASONRY SHALL NOT BE CRACKED.MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
CONFIGURATION
NOTES
CODE PANEL TYPE
O FIXED PANEL
X OPERATING PANEL
P POCKET
-BI-PARTING
TYPICAL ELEVATION
XP or PX
TYPICAL ELEVATION
XO, OX, XX, PXX, XXP or PX-XP
P
4 TRACK
CONFIGURATIONS
CONFIGURATION # OFTRACKS # OFPANELS
XXXXP 4 4
PXXXX 4 4
XXXX 4 4
XXXO 4 4
OXXX 4 4
2 TRACK
CONFIGURATIONS
CONFIGURATION # OFTRACKS # OFPANELS
XP 2 1
PX 2 1
XXP 2 2
PXX 2 2
XX 2 2
XO 2 2
OX 2 2
PX-XP 2 2
OX-O 2 3
O-XO 2 3
PXX-XXP 2 4
OX-XO 2 4
3 TRACK
CONFIGURATIONS
CONFIGURATION # OFTRACKS # OFPANELS
XXXP 3 3
PXXX 3 3
XXX 3 3
XXO 3 3
OXX 3 3
PXXX-XXXP 3 6
OXX-XXO 3 6
P P
P P
TYPICAL ELEVATION
XXXP, PXXX, XXXL, XXO, OXX, OX-O or O-XO
TYPICAL ELEVATION
XXXXP, PXXXX, XXXXL, XXXO, OXXX, PXX-XXP or OX-XO
TYPICAL ELEVATION
OXX-XXO or PXXX-XXXP
UNIT MAX. WIDTH SEE
SIZE CHART, SHEET 1
UNIT MAX.
HEIGHT
SEE SIZE
CHART,
SHEET 1
UNIT MAX. WIDTH SEE
SIZE CHART, SHEET 1
UNIT MAX.
HEIGHT
SEE SIZE
CHART,
SHEET 1
UNIT MAX. WIDTH SEE
SIZE CHART, SHEET 1
UNIT MAX.
HEIGHT
SEE SIZE
CHART,
SHEET 1
UNIT MAX. WIDTH SEE
SIZE CHART, SHEET 1
UNIT MAX.
HEIGHT
SEE SIZE
CHART,
SHEET 1
UNIT MAX. WIDTH SEE
SIZE CHART, SHEET 1
UNIT MAX.
HEIGHT
SEE SIZE
CHART,
SHEET 1
C
4
A
4
E
4
B
4
Configuration Notes:
- All configurations are available with pocket at
either or both jamb locations.
MAX. D.L.O. WIDTH SEE
PANEL SIZE CHART,
SHEET 1
MAX. D.L.O.
HEIGHT SEE
PANEL SIZE
CHART,
SHEET 1
MAX. D.L.O. WIDTH SEE
PANEL SIZE CHART,
SHEET 1
MAX. D.L.O.
HEIGHT SEE
PANEL SIZE
CHART,
SHEET 1
MAX. D.L.O. WIDTH SEE
PANEL SIZE CHART,
SHEET 1
MAX. D.L.O.
HEIGHT SEE
PANEL SIZE
CHART,
SHEET 1
MAX. D.L.O.
HEIGHT SEE
PANEL SIZE
CHART,
SHEET 1
MAX. D.L.O.
HEIGHT SEE
PANEL SIZE
CHART,
SHEET 1
C
4
MAX. D.L.O. WIDTH SEE
PANEL SIZE CHART, SHEET 1
MAX. D.L.O. WIDTH SEE
PANEL SIZE CHART, SHEET 1
F4 F
4
F
4 F4
C
4
C
4
C
4
C
4
A
4 A
4
A
4
A
4
B4
B4
B4
B4
E4
C
4
E4
C
4
E
4
C
4
E
4
C
4
D
4
D4
D4
CONFIGURATIONS & ELEVATIONSSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:4 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
DP35
DP50 HORIZONTAL SECTION
PXXX SHOWN
HORIZONTAL SECTION
O-XO SHOWN
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
EXTERIOR
INTERIOR
ASTRAGAL MAY BE
MOUNTED TO INTERIOR
ON REVERSE STACK
AND SOME POCKET
CONFIGURATIONS.
SEE GLAZING
DETAILS, SHEET 26
SEE GLAZING
DETAILS, SHEET 26
DETAIL C4
JAMBS
DETAIL D4
INTERLOCKDETAIL F4
ASTRAGALDETAIL C4
JAMBS
DETAIL C4
JAMBS
DETAIL D4
INTERLOCK
DETAIL D4
INTERLOCK
DETAIL E4
P-HOOK
DETAIL C4
JAMBS
Unit Width
Panel Width
Daylight
Opening
Unit Width HORIZONTAL SECTION DETAILSSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:5 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
PG 6
DP35 DP50
VERTICAL SECTION
2 TRACK SHOWN
VERTICAL SECTION
3 TRACK SHOWN
2-1/2" TOTAL
SILL HEIGHT
with
3/4" SILL RISER
3-1/2" TOTAL
SILL HEIGHT
with
1-3/4" SILL RISER
SEE GLAZING DETAIL,
SHEET 26
INTERIOR INTERIOR
EXTERIOR EXTERIOR
DETAIL A4
HEAD
DETAIL A4
HEAD
DETAIL B4
SILL
DETAIL B4
SILL
Panel
Height
Daylight
Opening
Height
Unit
Height
SEALANT SEALANT VERTICAL SECTION DETAILSSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:6 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
END HOLES
CENTER OF PANEL or
POCKET PATTERN
INTERLOCK / ASTRAGAL
PATTERN
2 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - HEAD
6" FROM
CORNERS,
TYP.
HEAD - DP35
TYPICAL PATTERN AT SPLICEMIN. EDGE DIST.,
SEE TABLE 1,
SHEET 2 OR
TABLE 2, SHEET 3
ADDITIONAL ANCHOR 4-0 & 5-0 MAX. PANEL SEE
TABLE 1, SHEET 2: ANCHOR ID - C, L, M, N and O.
END HOLES CENTER OF PANEL or
POCKET PATTERN INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
HEAD - DP50
INTERLOCK / ASTRAGAL PATTERN
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
END HOLES CENTER OF PANEL or
POCKET PATTERN
6" FROM
CORNERS,
TYP.
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
4" MIN.,
TYP.
4" MIN.,
TYP.
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAIL, SEE SHEET 26.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:7 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
2 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - SILL
END HOLES INTERLOCK / ASTRAGAL
PATTERN EXTERIOR
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
SILL - DP35
SILL - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. SILL NAIL FIN IS OPTIONAL.
5. 1/4" MAX. SHIM STACK.
6. SPLICE DETAIL, SEE SHEET 26.
7. FILL ALL PRE-DRILLED INSTALLATION HOLES WITH EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY SEALANT OVER THE HEAD OF SCREWS ONCE PROPERLY SEATED.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX.
PANEL SEE TABLE 1, SHEET 2:
ANCHOR ID - C, L, M, N and O.
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INTERIOR
END HOLES CENTER OF PANEL or
POCKET PATTERN INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
INTERLOCK / ASTRAGAL PATTERN
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
END HOLES CENTER OF PANEL or
POCKET PATTERN
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:8 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLES
EXTERIOR
ALL OTHER HOLES
INTERIOR6" FROM
CORNERS,
TYP.
16-3/4" O.C., TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
2 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - JAMBS
JAMB - DP35
JAMB - DP50
NOTES:
1. INSTALLATION HOLES ARE
FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2,
SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND
ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS
OPTIONAL FOR MASONRY
APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. FILL LEFT RIGHT PRE-DRILLED
JAMB INSTALLATION HOLES - 6"
FROM CORNER OF SILL ONLY, WITH
EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY
SEALANT OVER THE HEAD OF
SCREWS ONCE PROPERLY SEATED.
END HOLES ALL OTHER HOLES
6" FROM
CORNERS,
TYP.
16-3/4" O.C., TYP.
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
END HOLES ALL OTHER HOLES
6" FROM
CORNERS,
TYP.
16-1/2" O.C., TYP.
END HOLES ALL OTHER HOLES
6" FROM
CORNERS,
TYP.
15-1/4" O.C., TYP.
SEE TABLE 2, SHEET 3:
ANCHOR ID - A, D, F, G,
H, I, J, K, P, and Q.
SEE TABLE 2, SHEET 3:
ANCHOR ID - L, M, N, and O.
SEE TABLE 2, SHEET 3:
ANCHOR ID - B, C, and E.ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:9 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN
2 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - HEAD
HEAD - DP35
HEAD - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAIL, SEE SHEET 26.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX. PANEL SEE
TABLE 1, SHEET 2: ANCHOR ID - C, L, M, N and O.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:10 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
2 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - SILL
END HOLES INTERLOCK / ASTRAGAL
PATTERN
EXTERIOR
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
SILL - DP35
SILL - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. SILL NAIL FIN IS OPTIONAL.
5. 1/4" MAX. SHIM STACK.
6. SPLICE DETAILS, SEE SHEET 26.
7. FILL ALL PRE-DRILLED INSTALLATION HOLES WITH EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY SEALANT OVER THE HEAD OF SCREWS ONCE PROPERLY SEATED.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX.
PANEL SEE TABLE 1, SHEET 2:
ANCHOR ID - C, L, M, N and O.
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INTERIOR
END HOLES CENTER OF PANEL or
POCKET PATTERN INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
INTERLOCK / ASTRAGAL
PATTERN
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
END HOLES CENTER OF PANEL or
POCKET PATTERN
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:11 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
JAMB - DP35
JAMB - DP50
6" FROM
CORNERS,
TYP.
16-3/4" O.C., TYP.
6" FROM
CORNERS,
TYP.
16-3/4" O.C., TYP.
END HOLES ALL OTHER HOLES ALTERNATING
END HOLES ALL OTHER HOLE ALTERNATING
NOTES:
1. INSTALLATION HOLES ARE
FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE
2, SHEET 3 FOR FASTENER
MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER
SPACING.
3. 1X WOOD BUCK BY OTHERS IS
OPTIONAL FOR MASONRY
APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. FILL LEFT RIGHT PRE-DRILLED
JAMB INSTALLATION HOLES - 6"
FROM CORNER OF SILL ONLY,
WITH EXTERIOR GRADE SEALANT
PRIOR TO INSERTING SCREWS
AND APPLY SEALANT OVER THE
HEAD OF SCREWS ONCE
PROPERLY SEATED.
2 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - JAMBS
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
6" FROM
CORNERS,
TYP.
16-1/2" O.C., TYP.
END HOLES ALL OTHER HOLE ALTERNATING
6" FROM
CORNERS,
TYP.
15-1/4" O.C., TYP.
END HOLES ALL OTHER HOLE ALTERNATING
SEE TABLE 2, SHEET 3:
ANCHOR ID - A, D, F, G,
H, I, J, K, P, and Q.
SEE TABLE 2, SHEET 3:
ANCHOR ID - L, M, N, and O.
SEE TABLE 2, SHEET 3:
ANCHOR ID - B, C, and E.ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:12 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLE INTERLOCK / ASTRAGAL
PATTERN
6" FROM
CORNERS,
TYP.4" MIN.,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN
3 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - HEAD
HEAD - DP35
HEAD - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX. PANEL SEE
TABLE 1, SHEET 2: ANCHOR ID - C, L, M, N and O.
END HOLE INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
CENTER OF PANEL or
POCKET PATTERN
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
END HOLE INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
EXTERIOR
INTERIOR
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:13 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLES
INTERLOCK / ASTRAGAL
PATTERN
EXTERIOR
INTERIOR
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
3 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - SILL
SILL - DP35
SILL - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM EDGE
DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. SILL NAIL FIN IS OPTIONAL.
5. 1/4" MAX. SHIM STACK.
6. SPLICE DETAILS, SEE SHEET 26.
7. FILL ALL PRE-DRILLED INSTALLATION HOLES WITH EXTERIOR GRADE SEALANT PRIOR TO INSERTING SCREWS AND
APPLY SEALANT OVER THE HEAD OF SCREWS ONCE PROPERLY SEATED.
4" MIN.,
TYP.
4" MIN.,
TYP.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX.
PANEL SEE TABLE 1, SHEET 2:
ANCHOR ID - C, L, M, N and O.
MIN. EDGE DIST.,
SEE TABLE 1,
SHEET 2
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:14 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
3 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - JAMBS
JAMB - DP35
JAMB - DP50
NOTES:
1. INSTALLATION HOLES ARE
FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2,
SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND
ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS
OPTIONAL FOR MASONRY
APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. FILL LEFT RIGHT PRE-DRILLED
JAMB INSTALLATION HOLES - 6"
FROM CORNER OF SILL ONLY, WITH
EXTERIOR GRADE SEALANT PRIOR
TO INSERTING SCREWS AND APPLY
SEALANT OVER THE HEAD OF
SCREWS ONCE PROPERLY SEATED.
EXTERIOR
INTERIOR
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-1/2" O.C., TYP.16-1/2" O.C., TYP.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
15-1/4" O.C., TYP.15-1/4" O.C., TYP.
SEE TABLE 2, SHEET 3:
ANCHOR ID - A, D, F, G,
H, I, J, K, P, and Q.
SEE TABLE 2, SHEET 3:
ANCHOR ID - L, M, N, and O.
SEE TABLE 2, SHEET 3:
ANCHOR ID - B, C, and E.ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:15 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLES INTERLOCK / ASTRAGAL PATTERN
EXTERIOR
INTERIOR
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
3 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - HEADHEAD - DP35
HEAD - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX.
PANEL SEE TABLE 1, SHEET 2:
ANCHOR ID - C, L, M, N and O.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:16 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLES INTERLOCK / ASTRAGAL
PATTERN
EXTERIOR
INTERIOR
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
3 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - SILL
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
6. FILL ALL PRE-DRILLED INSTALLATION HOLES WITH EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY SEALANT OVER THE HEAD OF SCREWS ONCE PROPERLY SEATED.
SILL - DP35
SILL - DP50
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
END HOLES INTERLOCK / ASTRAGAL
PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX.
PANEL SEE TABLE 1, SHEET 2:
ANCHOR ID - C, L, M, N and O.MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:17 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
END HOLES ALL OTHER HOLES ALTERNATING
INTERIOR6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
3 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - JAMBS
JAMB - DP35
JAMB - DP50
NOTES:
1. INSTALLATION HOLES ARE
FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2,
SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND
ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS
OPTIONAL FOR MASONRY
APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. FILL LEFT RIGHT PRE-DRILLED
JAMB INSTALLATION HOLES - 6"
FROM CORNER OF SILL ONLY, WITH
EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY
SEALANT OVER THE HEAD OF
SCREWS ONCE PROPERLY SEATED.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-1/2" O.C., TYP.16-1/2" O.C., TYP.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
15-1/4" O.C., TYP.15-1/4" O.C., TYP.
SEE TABLE 2, SHEET 3:
ANCHOR ID - A, D, F, G,
H, I, J, K, P, and Q.
SEE TABLE 2, SHEET 3:
ANCHOR ID - L, M, N, and O.
SEE TABLE 2, SHEET 3:
ANCHOR ID - B, C, and E.ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:18 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
4 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - HEAD
HEAD - DP35
HEAD - DP50
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX. PANEL SEE
TABLE 1, SHEET 2: ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.
4" MIN.,
TYP.
MIN. EDGE DIST.,
SEE TABLE 1,
SHEET 2 OR
TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:19 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
END HOLES INTERLOCK / ASTRAGAL
PATTERN
EXTERIOR
INTERIOR
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - SILL
SILL - DP35
SILL - DP50
4" MIN.,
TYP.
4" MIN.,
TYP.
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM
EDGE DISTANCE, EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
6. FILL ALL PRE-DRILLED INSTALLATION HOLES WITH EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY SEALANT OVER THE HEAD OF SCREWS ONCE PROPERLY SEATED.
ADDITIONAL ANCHOR 4-0 & 5-0 MAX. PANEL SEE
TABLE 1, SHEET 2: ANCHOR ID - C, L, M, N and O.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4" MIN.,
TYP.
4" MIN.,
TYP.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.
4" MIN.,
TYP.ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
PG 21 ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:20 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
4 TRACK ANCHOR LAYOUT DETAILS WITH NAIL FIN - JAMBS
JAMB - DP35
JAMB - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED
BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2,
SHEET 3 FOR FASTENER MINIMUM EDGE
DISTANCE, EMBEDMENT AND ON
CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL
FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. FILL LEFT RIGHT PRE-DRILLED JAMB
INSTALLATION HOLES - 6" FROM
CORNER OF SILL ONLY, WITH EXTERIOR
GRADE SEALANT PRIOR TO INSERTING
SCREWS AND APPLY SEALANT OVER
THE HEAD OF SCREWS ONCE PROPERLY
SEATED.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-1/2" O.C., TYP.16-1/2" O.C., TYP.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
15-1/4" O.C., TYP.15-1/4" O.C., TYP.
SEE TABLE 2, SHEET 3:
ANCHOR ID - A, D, F, G,
H, I, J, K, P, and Q.
SEE TABLE 2, SHEET 3:
ANCHOR ID - L, M, N, and O.
SEE TABLE 2, SHEET 3:
ANCHOR ID - B, C, and E.ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:21 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - HEAD
HEAD - DP35
HEAD - DP50
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
ADDITIONAL ANCHOR 4-0 & 5-0 MAX. PANEL SEE
TABLE 1, SHEET 2: ANCHOR ID - C, L, M, N and O.
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
4" MIN.,
TYP.
ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.
4" MIN.,
TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:22 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
PG 24
END HOLES INTERLOCK / ASTRAGAL PATTERN
EXTERIOR
INTERIOR
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
4 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - SILL
SILL - DP35
SILL - DP50
NOTES:
1. INSTALLATION HOLES ARE FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE 2, SHEET 3 FOR FASTENER MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER SPACING.
3. 1X WOOD BUCK BY OTHERS IS OPTIONAL FOR MASONRY APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. SPLICE DETAILS, SEE SHEET 26.
6. FILL ALL PRE-DRILLED INSTALLATION HOLES WITH EXTERIOR GRADE SEALANT PRIOR TO
INSERTING SCREWS AND APPLY SEALANT OVER THE HEAD OF SCREWS ONCE PROPERLY SEATED.
4" MIN.,
TYP.
4" MIN.,
TYP.
ADDITIONAL ANCHOR 3-0 MAX. PANEL
SEE TABLE 2, SHEET 3:
ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.4" MIN.,
TYP.ADDITIONAL ANCHORS 4-0 & 5-0 MAX. PANEL SEE
TABLE 2, SHEET 3: ANCHOR ID - C, L, M, N and O.
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
END HOLES INTERLOCK / ASTRAGAL PATTERN
6" FROM
CORNERS,
TYP.
CENTER OF PANEL or
POCKET PATTERN
ADDITIONAL ANCHOR 4-0 & 5-0 MAX.
PANEL SEE TABLE 1, SHEET 2:
ANCHOR ID - C, L, M, N and O.
4" MIN.,
TYP.
4" MIN.,
TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE
TYPICAL PATTERN AT SPLICE ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:23 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
EXTERIOR
INTERIOR
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
4 TRACK ANCHOR LAYOUT DETAILS BOX FRAME - JAMBS
JAMB - DP35
JAMB - DP50
NOTES:
1. INSTALLATION HOLES ARE
FABRICATED BY MANUFACTURER.
2. SEE TABLE 1, SHEET 2 OR TABLE
2, SHEET 3 FOR FASTENER
MINIMUM EDGE DISTANCE,
EMBEDMENT AND ON CENTER
SPACING.
3. 1X WOOD BUCK BY OTHERS IS
OPTIONAL FOR MASONRY
APPLICATIONS.
4. 1/4" MAX. SHIM STACK.
5. FILL LEFT RIGHT PRE-DRILLED
JAMB INSTALLATION HOLES - 6"
FROM CORNER OF SILL ONLY,
WITH EXTERIOR GRADE SEALANT
PRIOR TO INSERTING SCREWS
AND APPLY SEALANT OVER THE
HEAD OF SCREWS ONCE
PROPERLY SEATED.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-3/4" O.C., TYP.16-3/4" O.C., TYP.
MIN. EDGE DIST.,
SEE TABLE 1, SHEET 2
or TABLE 2, SHEET 3
MIN. EMBED.,
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
INSTALLATION ANCHOR
FOR WOOD SUBSTRATE
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
16-1/2" O.C., TYP.16-1/2" O.C., TYP.
END HOLES ALL OTHER HOLES ALTERNATING
6" FROM
CORNER,
TYP.
15-1/4" O.C., TYP.15-1/4" O.C., TYP.
SEE TABLE 2, SHEET 3:
ANCHOR ID - A, D, F, G,
H, I, J, K, P, and Q.
SEE TABLE 2, SHEET 3:
ANCHOR ID - L, M, N, and O.
SEE TABLE 2, SHEET 3:
ANCHOR ID - B, C, and E.
INSTALLATION ANCHOR
FOR MASONRY SUBSTRATE
SEE TABLE 1, SHEET 2
OR TABLE 2, SHEET 3
MASONRY SUBSTRATE WOOD SUBSTRATE
MASONRY SUBSTRATE WOOD SUBSTRATE
WOOD SUBSTRATE
MASONRY SUBSTRATE
WOOD SUBSTRATE
MASONRY SUBSTRATE ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:24 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
P-HOOK ANCHOR LAYOUT
INSTALLATION ANCHOR,
SEE TABLE 3
INSTALLATION ANCHOR,
SEE TABLE 3
PLACE BEAD OF SILICONE
THE ENTIRE LENGTH
PLACE BEAD OF SILICONE
THE ENTIRE LENGTH
MAX. 6" FROM
EACH END, TYP.
MAX. 2" FROM
EACH END, TYP.
MAX. 12" O.C.,
TYP.MAX. 12" O.C,
TYP.
DETAIL E4
P-HOOK
MIN. EMBED.,
SEE TABLE 3
MIN. EDGE DIST.,
SEE TABLE 3
NOTES: -PRE-DRILLING FOR ANCHORS INTO WOOD IS RECOMMENDED.
-CONCRETE/MASONRY SHALL NOT BE CRACKED.
TABLE 3: P-HOOK INSTALLATION FASTENERS TABLE
ID SUBSTRATE TYPE ANCHOR TYPE MIN. EDGE
DISTANCE
MIN.
EMBED.
MIN. ON-CENTER
SPACING
R CONCRETE (3.05 KSI MIN) 3/16" DEWALT ULTRACON+
COATED CARBON STEEL 1"1"3"
S HOLLOW OR GROUT-FILLED CMU
(ASTM C-90)
3/16" DEWALT ULTRACON+
COATED CARBON STEEL 1"1-1/4"3"
T 2x MIN. SPRUCE-PIN-FIR WOOD
(G=0.42 MIN) #8 GRADE 5 STEEL WOOD SCRW 1" 1-1/4"3"
U 16 GAUGE (0.060") MIN. STEEL
STUD, 33 KSI MIN. YIELD
#10-16 ITW-TEKS, DEWALT
DRIL-FLEX, or HILTI KWIK-FLEX
SELF DRILLING SCREW
1/2"FULL PLUS 3
THREADS MIN.3"
V 1/8" ALUM. 6063-T5 MIN. or
1/8" STEEL 33 KSI MIN.
#10-16 GRADE 5
SELF-TAPPING/DRILLING SCREW 1/2"FULL PLUS 3
THREADS MIN.3"
PG 25
PG 26
SEE NOTE 13, SHEET 1
P-HOOK ANCHOR LAYOUTSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:25 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601
GLAZING DETAIL 1
EXTERIOR
INTERIOR
7/8" GLASS
BITE
7/8" O.A. INSULATED GLASS
CONSISTING OF:
1/8" TEMPERED
AIR SPACE
1/8" TEMPERED
GLAZING COMPOUND
PERFECT GLAZE
GLAZING DETAIL 3
EXTERIOR
INTERIOR
7/8" GLASS
BITE
7/8" O.A. INSULATED GLASS
CONSISTING OF:
3/16" TEMPERED
AIR SPACE
3/16" TEMPERED
GLAZING COMPOUND
PERFECT GLAZE
PG 26
GLAZING DETAIL 2
EXTERIOR
INTERIOR
7/8" GLASS
BITE
7/8" O.A. INSULATED GLASS
CONSISTING OF:
5/32" TEMPERED
AIR SPACE
5/32" TEMPERED
GLAZING COMPOUND
PERFECT GLAZE
APPLY SILICONE TO THE FACE
OF FRAME PROFILE BEFORE
CONNECTING SPLICE.
SPLICE SCREWS
#8 X 1" FLAT HEAD
SELF DRILLING
2 PER SPLICE
ADAPTER
1-1/2" TYP. FROM
SPLICE JOINT
SPLICE DETAILS
6" SPLICE
ADAPTER
GLAZING DETAIL 4
EXTERIOR
INTERIOR
7/8" GLASS
BITE
1-1/16" O.A. INSULATED GLASS
CONSISTING OF:
1/8" or 5/32" or 3/16" TEMPERED
AIR SPACE
1/8" or 5/32" or 3/16" TEMPERED
AIR SPACE
1/8" or 5/32" or 3/16" TEMPERED
GLAZING COMPOUND
PERFECT GLAZE
GLAZING NOTE:
GLASS THICKNESS AND TYPE SHALL COMPLY WITH
ASTM E-1300 GLASS CHART REQUIRMENTS.GLAZING & SPLICE DETAILSSHEET:
DWG #:TITLE:SCALE:DWN BY:NO.REVISION DESCRIPTIONCHK BY:OFDATE:26 26 NTSLMHSAS05/16/22DATEBYUPDATED PANEL SIZE CHARTLMH08.19.22AN22-023 ADDED TEST SIZESLMH08.25.23BFL#:MAXVIEW Multi-Slide Patio Door1 COCHRANE AVENUE
PENNSBORO, WV 26415PH: 800-542-9118
41795
IN0601