Loading...
1853 SELVA GRANDE DR POOL24-0010 Brinkley Hydraulics Form© 2020 Pool & Hot Tub Alliance ___ ___ ___ ___ ___ !1. _________ gallons !2. _________ gpm !3a. _________ inches !3b. _________ inches !3c. _________ inches !3d. _________ inches ___ ___ 4a. ________________ !4b. _________ sq. ft.___ 5. _________ inches ___ Table 1 (When used) !6a. ________________ !6b. _________ ___ ___ or !7a. ________________ !7b. _________ gpm ___ ___ §5.3.2.1: Pools 17,000 gallons or less, select pump* from the database with a Curve A gpm flow equal to item 2 or less. §5.3.2.2: Pools 17,001 gallons or more, select pump* from the database with a Curve C gpm flow equal to item 2 or less. *Multi-speed pumps must have one speed listed that satisfies this requirement. a.Pump model b.Pump flow (§5.3.2.1, §5.3.2.2: Applicable Curve A or C gpm flow listed in database) 6. Single-speed pump selection (when used): ANSI/APSP/ICC-15 ENERGY EFFICIENCY COMPLIANCE INFORMATION FOR RESIDENTIAL SWIMMING POOLS PROJECT NAME: AND ADDRESS CONTRACTOR NAME AND ADDRESS: OWNER:CONTRACTOR PHONE:DATE: This information sheet was prepared by the APSP-15 Residential Swimming Pool and Spa Energy Efficiency Standard Writing Committee (SWC) of the Pool & Hot Tub Alliance (PHTA). It is not part of the American National Standard ANSI/APSP/ICC-15 2011 but is included for information only. (Enter the smallest pipe size from Table 1 with a 6 fps flow capacity the same or more than item 2.) b.Minimum suction branch pipe diameter (Calculate: Item 2. ______(gpm) ÷ Branch Pipes ______(quantity) = branch flow rate _______(gpm). Enter the smallest pipe size from Table 1 with a 6 fps flow capacity the same or more than the calculated suction branch flow rate.) c.Minimum return pipe diameter (Enter the smallest pipe size from Table 1 with a 8 fps flow capacity the same or more than item 2.) d.Minimum return branch pipe diameter (Calculate: Item 2. ______(gpm) ÷ Branch Pipes ______(quantity) = branch flow rate _______(gpm). Enter the smallest pipe size from Table 1 with a 8 fps flow capacity the same or more than the calculated return branch flow rate.) 4.§5.4.1: Filter type and size: a.Filter type: (Cartridge, DE, Sand) b. Minimum filter area (Calculate: item 2. _______(gpm) ÷ filter factor _______ (gpm/ft 2)) Filter factors: Cartridge=0.375, Sand=15, Diatomaceous Earth=2 5.§5.4.2: Backwash valve: ____Yes,____No(When using a backwash valve, enter result of item 3c or 2 inches whichever is larger) APSP-15 & APSP-7 COMPLIANCE DOCUMENTATION AND SIZING CALCULATOR §5.1.1, 5.3.1: For single-speed pumps with a total horsepower 0.99 or less, find and enter a compliant pump from the Pool Pump Database. a.Pump model b.Total horsepower 7. Multi-speed pump selection (when used): 1.§5.2.1: Calculated pool volume 2. 3.§5.5.1: Pipe sizing: a.Minimum suction pipe diameter (Pool volume ÷ 360 or 36gpm whichever is larger) 2. §5.2.1: Calculated filtration flow rate a. Gallons: ___________; or b. Calculated Gallons: ________(surface area) X ________ (average depth) X 7.48 (gal/ft 3) = _________ Component Section Check 4.4.1.1 4.4.1.2 4.3.1.3 4.3.2 5.1.1 5.3.1 5.3.3 5.3.4 5.5.2 5.5.3 5.6 Pool systems Pool filter pump listed in database. Pool filter pump with total horsepower 1.0 or more is multi-speed. Multi-speed pump controller programmed to default to the filtration flow rate when no auxiliary pool loads are operating within 24 hours and programmed with temporary override capability for servicing. Single-speed pump controller capable of operating pump during off-peak electric demand. Pipe before pump has at least 4 diameters of straight pipe. System installed with solar, or setup for the future addition of solar heating equipment by installing 18 inches of horizontal or vertical pipe after the filter and before a heater, or built-in or built-up connections, or dedicated pipe to and from the pool. Directional inlets for mixing pool water. ANSI/APSP/ICC-15 ENERGY EFFICIENCY COMPLIANCE INFORMATION FOR RESIDENTIAL SWIMMING POOLS Requirements Heaters Heater has no pilot light. Readily accessible on-off switch mounted outside of the heater. No electric resistance heating unless for inground spa with tight fitting cover with R-6 insulation, or for pool with 60% of documented pool heating from on-site solar or recovered energy. Heater efficiency: gas/oil-fired heater efficiency at least 82%, heat pump COP at least 4.0. © 2020 Pool & Hot Tub Alliance N/A N/A 2.5 117 .09 2.5 117 .09 .09 .09 3 117 2.5 117 2.5 117 117 MDX/SDX X MDX/SDX 132 X APSP SHEET Jandy VSSHP220DV2A 102 102 102 9.2 9.2 18.4 7 16 54 12.6