2383 MAYPORT RD ROOF24-0029 Insulfoam a div of Carlisle Mat NOA No. 23-1012.02
Expiration Date: November 29, 2027
Approval Date: November 16, 2023
Page 1
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/building
Insulfoam, a div. of Carlisle Construction Materials, LLC.
19727 57th Avenue, East
Puyallup, WA 98375
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER-
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to
perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may
immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER
reserves the right to revoke this acceptance if it is determined by Miami-Dade County Product Control Section
that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein and has been designed to comply with the Florida Building
Code, including the High Velocity Hurricane Zone.
DESCRIPTION: Insulfoam Expanded Polystyrene Preformed Block Type I Insulation
APPROVAL DOCUMENT: Drawing No. A6651.06, titled “Preformed Expanded Polystyrene”, sheet 1
of 1, dated 11/30/12, with revision 5 dated 09/04/23, prepared manufacturer, signed and sealed by Scott
Wolters, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of
Acceptance number and expiration date by the Miami-Dade County Product Control Section.
MISSILE IMPACT RATING: None
LABELING: Each board shall bear a permanent label with the manufacturer's name or logo, city, state and
following statement: "Miami-Dade County Product Control Approved", unless otherwise noted.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been
no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change
in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement
of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure
to comply with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No. 22-0628.11 and consists of this page 1 and evidence pages E-1
and E-2, as well as approval document mentioned above.
The submitted documentation was reviewed by Carlos M. Utrera, P.E.
Carlos M. Utrera, P.E.
Product Control Examiner
NOA No. 23-1012.02
Expiration Date: November 29, 2027
Approval Date: November 16, 2023
E - 1
Insulfoam, a div. of Carlisle Construction Materials, LLC.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s
A. DRAWINGS (Submitted under NOA No. 21-0216.04)
1. Drawing No. A6651.06, titled “Preformed Expanded Polystyrene”, sheet 1 of 1, dated
11/30/12, with revision 4 dated 03/30/21, prepared by manufacturer, signed and sealed by
Scott Wolters, P.E.
B. TESTS (Submitted under NOA No. 17-0221.06)
Laboratory Report Test Date Signature
1. RAD-3015 ASTM C303 10/29/07 Ray F. Tucker, P.E.
2. RAD-3015 ASTM D1621 10/29/07 Ray F. Tucker, P.E.
3. RAD-3015 ASTM C203 10/29/07 Ray F. Tucker, P.E.
4. RAD-3015 ASTM C272 10/29/07 Ray F. Tucker, P.E.
5. RAD-3015 ASTM E96 10/29/07 Ray F. Tucker, P.E.
6. RAD-3015 ASTM D2126 10/29/07 Ray F. Tucker, P.E.
7. RAD-3015 ASTM C518 10/29/07 Ray F. Tucker, P.E.
8. 3082960-500 Alt.1 ASTM E84 10/29/07 Ray F. Tucker, P.E.
9. 3082959-500 Rev2 ASTM D1929 10/29/07 Ray F. Tucker, P.E.
C. CALCULATIONS
1. None.
D. QUALITY ASSURANCE
1. Miami-Dade Department of Regulatory and Economic Resources (RER).
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENTS (Submitted under NOA No. 21-0216.04)
1. Statement letter of code conformance to the FBC 7th Edition (2020), dated 03/30/21, issued
by Wolters Engineering, signed and sealed by Scott Wolters, P.E.
2. Certificate of conversion of a Delaware corporation under the name of “Carlisle Construction
Materials Incorporated” to a Delaware limited liability company, dated 12/31/2015, signed by
Jeffrey W. Bullock, Secretary of State. (Submitted under NOA No. 19-0129.06)
3. Certificate of amendment of Carlisle Syntec Inc. to Carlisle Construction Materials Inc. dated
12/31/2009. (Submitted under NOA No. 14-0311.08)
4. Certificate of cancellation of Insulfoam LLC dated 12/31/09.
(Submitted under NOA No. 14-0311.08)
Insulfoam LLC limited liability agreement dated 05/01/07.
(Submitted under NOA No. 14-0311.08)
5. Certificate of formation of Insulfoam LLC dated 03/12/07.
(Submitted under NOA No. 14-0311.08)
Carlos M. Utrera, P.E.
Product Control Examiner
NOA No. 23-1012.02
Expiration Date: November 29, 2027
Approval Date: November 16, 2023
E - 2
Insulfoam, a div. of Carlisle Construction Materials, LLC.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
2. EVIDENCE SUBMITTED UNDER NOA # 22-0628.11 AND NEW
A. DRAWINGS
1. Drawing No. A6651.06, titled “Preformed Expanded Polystyrene”, sheet 1 of 1, dated
11/30/12, with revision 5 dated 09/04/23, prepared manufacturer, signed and sealed by
Scott Wolters, P.E.
B. TESTS
Laboratory Report Test Date Signature
1. P0855.02-106-18 R0 ASTM D1929-20 09/09/22 Tanya A. Dolby, P.E.
2. P0855.04-116-25 R0 ASTM C518-21 08/12/22 Eric S. Loitner
C. CALCULATIONS
1. None.
D. QUALITY ASSURANCE
1. Miami-Dade Department of Regulatory and Economic Resources (RER).
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENTS
1. Statement letter of code conformance to the FBC 8th Edition (2023), dated
09/05/2023, issued by Wolters Engineering, signed and sealed by Scott Wolters, P.E.
2. Statement letter requesting this product to be renewed and certifying that it has not
changed, dated 06/16/22, issued by Insulfoam, signed by Jamie Moore, Technical
Engineer.
3. Testing agreement letter, dated 07/16/22 between Intertek-ATI (Architectural Testing)
and Insulfoam, issued by Intertek and signed by Felita Carreras, Project Facilitator.
4. Email from manufacturer requesting a 1-year extension to allow time to perform
verification test, dated 08/03/22, signed by Jamie Moore, Technical Engineer.
PRODUCT REVISED as complying with the Florida Building CodeNOA–No. Expiration Date By Miami–Dade Product Control 23–1012.0211/29/2027