The URL can be used to link to this page

Certified Air Contractors (in vault) SUBMITTAL FOR ATLANTIC BEACH CITY HALL ADDITION AND ALTERATIONS 800 SEMINOLE ROAD ATLANTIC BEACH, FLORIDA 32233 GENERAL CONTRACTOR C.C. BORDEN CONSTRUCTION, INC. C� \ 1019 ROSELLE STREET i JACKSONVILLE, FLORIDA f r- is Q1 � MECHANICAL CONTRACTOR v CERTIFIED AIR CONTRACTORS, INC. 4505 MARQUETTE AVENUE JACKSONVILLE, FLORIDA OF p�NG o C v0. 104, FES cilosw 7 INDEX 1. CARRIER A/C EQUIPMENT ............................................................................... TAB 1 2. INSULATION........................................................................................................ TAB 2 3. AIR DISTRIBUTION............................................................................................. TAB 3 4. DUCTWORK......................................................................................................... TAB 4 5. TEST AND BALANCE.......................................................................................... TAB 5 JC, 4r,1,4,Vr CERTIFIED CONTROL SYSTEMS SHEET NO. or state Certification #CAC008251 DATE 4505 Marquette Avenue CALCULATED BY JACKSONVILLE, FLORIDA 32210 CHECKED BY DATE (904) 384-4013 Fax: (904) 389-6803 SCALE ............ ............ .................................... ................................ ............ ... ............ ..................... .......... ......... .........._i............ ....................................................... .......................... .... ............ ................. :............ I........... .................................. ............. ................................ ........... ...........;............. ...... ............. ............... ............. ........... . ............. ......................i........................................................... ............. ............................................. m............a ...........................a._......._......... .......... ............. ......................... ........... ........ .........j........_.,. ..................... .................... ...................... ....................................................... .................. ............ ... . .......... .............................................. ......... ........ ............. ............J.................................. .......... .......... ..... ....................... .............. ............ .......... ............ ..................................... ........ ............ 4............. ............ .......... ........... '4....................... ............. ...... .. .......... ... .............. .... ......... ......................... ........... ............ .... .. .. ........ ..................... ....... ...... ....... .. .......... .........I g I ple g. ......................... ............ ....................................... ................... .................................... A............................................................. . ............. .......... ................ .. ............. .... .......... ........... ....................................... ........... .......... ............. ............ ........... .............i.............«............. ................................... .............. .......... .......... ........................ .......... ............. ............. ............A .......... ............ ...........I......... ............. ........................................ ..... ..... ........... 17: ...................1 ....... ... .. ......... ........... ................. --!............. ................................. ............1............... ..... ............ ............ ....... ..... .............. ..... ....... .. ... .. ............ .................................... .......................... .............................. ................ ............ ...................................... ........... ...................... ........... ........... ............. .......... . .......... .......... ............. ................ ...... ...... ........... .................... .... ................. .... ............................. .............. ............. ................_•...._....._. ............ ...... ............; T" ..... II..... I................ ..: ........... .......................................................... ............. .......................... ......... ........... .............. __................................1............ ........... .......... .......... ............ .................................... .............................................................. ........... ...... ......................... ................................ ............ ....................................... i 4 AA ....................................... ....................... ................................. ........... ........................ ............... ...................... ............ ............ ........................ .............. ............. ......... ........... .................. ............ ........... .......... .......... ............. ........... ..........i !.......... ....... ....... ........... .......... r.................................................... ........... ................. ............. ............ .......... .......................... ........ ...................... ............ ............ ................I.»....»....1...... . .......... . ... ........ ......... ......... ....................... ........................... . ..................... ....... ................ ..... ... ........... .... .......... ....................... ...j.... .......... ..............I i........... ........... ....... J ............. ............... ................................................................. ............ ................... .... ...... ........................ ..... ..........................1.......................................................... .......... .......... .......... ...................................... 1 ....................... j......._..._....... ............. ....... ...................................... ..................... ...... .......... ........... ........ ...... ......... ................... ...... ....................... ... . ... ........................................ .......................................I ............. .......... .................................... ........................ ............................. ........ ...... ........... ............ ................................... ............ ...................................... .................................... ......................... ......................................................................... ....................... .............................. .......... ........... ................................................................................................................ .................... . ............... ......................... ..... ............................... ................. ....... ............ ............. !.......................... ......................... . ...... ............. ....) .......... ........ ................... .............. i ................ .....?. 0..........ezv ........... ..............[ �,_ i A'- ' .4...................... ..........4.. ............ ................................... ............................................................ ............ -.4............................................... ....................................................................... ....... ...................... .. ........ ...... .............. .. .......... I....... 6. _77.C../W4 ..... .................F...... r,oix ....... ........ ......................... fi ............ w1i..... ........ ....... ......I......................... 4 ! . ......... .......... ............................................ ....................................... ..........I,...................................... ................... ...................... ...... . ............ .............. .............i % ... ........... ............. ........... ................................................... ..._...'....._.._.i...........4. ........... .............. ................... ..............................................................................I................... .................. .......... ............. .................................. T ell .......... .......................... ........... ........................................................... .............. ............. .4...........t ............. ........... ............ ............ ........... ........ + ......................... ...............4.......................I ......... ............. ..................................................................................... ............................. ............. .......... .................. ............. .6 t— CERTIFIED CONTROL SYSTEMS SHEET NO. OF State Certification #CAC008251 CALCULATED By DATE 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 CHECKED BY DATE ,(904) 384-4013 Fax: (904) 389-6803 SCALE .......... ........... . ...................... ............. .............. ........................................................... ............ ............. ............................................ ....................... ........ ........... ......................... .......... .................................... ...................... ....... ............ ......... ..................... .......... ................................................I. ...........+........._.i..........._'. ........ .......... . ..... ....................... .......... ......... ............. ...... ...................... ii iI ii1,i ii ii Ik ii ��tEiF` iI fi ji if MAIO ....... .............. ..................... ik iI ii .......... ......................... .......................... ............. ........... ............ .................................................. ...............»......_.i............. ........................ ...................... .......... ............ ......................... ........... ........................... ............ ......................... ......................... ................. ......................... ........... ................................................. ........... .......... ............ ................. 4-- ....................... ........................ ...................................... ............4......................... ........... .......... ............. ........... .................................................. ............................ ........... ........... ........... ........... ...................... .......... .......... .......... ............... ... .....- ........... ........... ......_.....i.._........+........._.. .......... ........................ L............ ...........- .................. .............. .................................. ............ ........... .......... ................ 4 1 ............................ .... .................. ..........- .......... .... ........... ............. ........... .. ....... . ............. ...................... ........................ .......... Ti .................... .......... .... ................................................... ............ I t .......... .......... .......... ......................... ............. J ........... .......... .................................................. ..........." ........... - ........... ............ ...................... ............. ........... 111-41 .......... AOL ............... ............ ............ .............. ..... ............. ........ ........................ ................... .......... .......... ............ ................ ............ ................ ....................... .............30]....................... ........................ ...... ........... ......J z........... ........... .......... ........... ................................................. ............................ .................... ................... ............ .................. ............. . .................... ...... ..... ............ ..................................... ............ ....................... ........- ............ ....................................... ............ ....... ............ ............ ............ ........ ............. ........... ....... ................................... .......... ........................................................................................................................... . ..... .......... ............ ............ ...... ........ .......... ............ ........... 41 ...................................... ... ..... .......................... ............. ......................... ................... .................................................................. ........... .......... ......... ......... .......................... ................................................... ............................... ....................... ........... 1 ._............ A.— ............................................................... fifIII iits if 1i�ii! ii t ....................................... ... ............. ...... ........ ................ ............. ....................... .......... ...... .... ................................ .................................................................................................................._..i............. ... .................... ............ ...................................... - ---- ....... —4...... ............+..................... ........... 4 .......... ....................... ......................A .................................................................................. ......................................................................................... ........... ................................... ............ ............. .......... ............................................................... ........................ ............ ..................... ............................................ ....... ..........................................................i...._.»...:...................................... V................. ............ ............................................. ............. ............ .........................4.....................................4........................ .................... ... .......... ............ ........... .......................................................... .......... .................... ........... ........... ............. ..................................... ....................... ............... ............ ........... .......... .......................... .......... ............ .............I................................... ............ ........................ ....................... ......a........... ........._— .... ............4............................................... .................. .... .... ........ .......... ............. —j...........i.........................4-— ...... .... ........................ .............. ............ ................... ............t ................. .......... .......... .......... .................................... .................................... ............. ..................... ............. .................................I.................................... ................................... ............ i......... .............I ...................................... ..........4 .............. ........... .......... ............................................................. ................................................................................. ......... ................ ............4....................... ......................................... T ............. 4 4 ....................... ............................................................... ................................. ........... .............................................................. .............................................................. ............ J ...................................... ................................. ....................... ...........I.............1........................ ..................... ................................. T ................... ........... ........... 1 4 4 .......... .................- ............. ............. ..................... ................... ........................................... .......... ........... 04/27/2005 20:18 9042240023 POH ARCHITECTS PAGE 03 04/27/2005 13:46 FAX 0046366770 McYEIGH & MANGLE►( PQH Q002/003 ------ f, -_ LJ E715TG WALL- u TO REMAIN 5TUOS TO AIN O CORNER UN ` DOST 4-2x'12 WALL TO --�g��p�lE j EXS 3-2w5 -2xa - _-___-- �. - -- NEW STUD r, ALLS LJ 8 II 1 II \ I \ POW STUDS %5TC S COL � BELOW� 4-2w12 BEAM . N II �I r, li LJ Z 1 II I II I II Z I O I i ---- -- ---------J� 1 ------- -� I 1 1 F-1 EXSTG WALL TO REMA PI I I I w000 ca ;I I 1 Q 1 I I L; I �iWALL TO I I eE Kum mi i i C 6XSTG STUD C TO REMAIN EXSTG WALL TO REMAIN �J I� LJLJ .,...... - ______________ L, I CEIVED y�ccTIMEZZANINE FLAN �1 JF ATLANTIC BEACH EX135NG Z BUILDING &ZONING SCALE: V-O' NOTES: APR 2 8 2005 1) FOR DMON CRITERIA AND GENERAL NOTES. SEE SHEET 5-4. 2) VERIFY ALL E10STG CONOITIONS AND DIIAENSIONS ARE CORRECT AS SHOWN BEFORE FABRICATION OR CONSTRUCTION. BY: 04/27/2005 20: 18 9042240023 PQH ARCHITECTS PAGE 04 04/27/2005 13:46 FAX 8046366770 McVBIGH & MOGUM r PQH IZ003/003 w nnh� Oxi ,^^ m EA 0 V/ ;0 ` J LOA +i 00. y z Or pm LA N pp LA ty� n N O �ai rvi D _D Orn fA x wO aCMtoCI in Z ,. m ZO i� �jg rri C) Dm� x� a . c� s s o Fin w � LA s rn � 9 4 ca m No a_ Z 1 O a N x X � � N r f rq -4 F9 x � �a > r F F8 Z �� y 4 ao r w N m 04/27/2005 20:18 9042240023 PQH ARCHITECTS PAGE 01 PEREZ-QUINONES- HOENSHEL PEO I 4141 Southpoint Drive E.,Suite 200 Jacksonville, Florida 32216 FAX �R"HirEc�rs s 0 4 - 224. 0001 1:1001:1111:10 FA X 224 - 0023 To: Don Ford )(Date: April 28,2005 Company: City of Atlantic Beach Fax No: (904)247-5$45 Building Department Subject- Additions and Alterations Atlantic Beach City Hall Pages:_4 (Incl.Covcr Shcet) MESSAGE: To follow,Pax Memo and Sketches from McVeigh and Mangum Engineering,Inc,concerning changes to framing at existiuig building connection per our meeting yesterday.Please call should you have any questions. From The Desk of: QQ �_/ Daziie. S. Strickland Construction Administrator IF YOU DO NOT RECEIVE ALL OF THE PAGES,PLEASE CALL(904)224-0001. THIS INFORMATION CONTAINED JN TMS FACSFMME IS PRIVILEGED AND CONFIDENTIAL INFORMATION INTENDED ONLY FOR THE USE OF THE INDIVIDUAL OR ENTTTY NAMED ABOVE. IF THE READER OF THIS MESSAGE IS NOT THE INTENDED RECIPIENT, YOU ARE HEREBY NOTIFIED THAT ANY DISSEMINATION,DISTRIBUTION OR COPYING OF THIS COMMUNICATION IS STRICTLY PRO.HIH rED. IF YOU HAVE RECEIVED THIS COMMUNICATION IN ERROR, KJASE.IMMEDIATELY NOWN US COLLECT HY TELEPHONE AND RETURN THE ORIGINAL MESSAGE TO US AT THE ABOVE ADDRESS VIA THE U.S.POSTAL SERVICE.......—_.THANK YOU. 04/27/2005 20:18 9042240023 PQH ARCHITECTS PAGE 02 04/27/2005 13:45 FAX 9046366770 NOEIGH & UNGUN PQH Q001/003 MCVE IGH&MANGUM. E N G I N E E R I N G - I N C FACSIMILE TRANSMISSION To: Danny Strickland Date: April 27,2005 Company: PQ-T4 Fax No,:224-0023 Project: Atlantic Bcach City Hall MME Job#: 04055 From: Michael Brimeyer No.of Pages: 1 of 3 mikeb@mcveighmangum.com cc: Danny, Please see the attached sheets for the revised layout to the mezzanine framing per our meeting this morning. Sincerely, Michael Brimeyer,P.E. McVeigh&Mangum Engineering,Jnc STRUCTVRAL MECHANWAL ELECTRICAL FwMOINC 92SO Cypress Green Drive - Suite 202 - Jaekno+.+.v11.1e, Florida 32256 (904) 737-0701. • Psa 19041 636-6770 mailOnmcveighmangum.com GREG NORMAN CARRIER OF NORTH FLORIDA 9093 PHILLIPS HIGHWAY JACKSONVILLE, FL 32256 PHONE: (904) 363-1991 FAX: (904) 363-8863 SUBMITTAL DATA PROJECT: ATLANTIC BEACH CITY HALL EQUIPMENT SUBMITTED: 38YDB/38BYC FV4BNF/FK4DNF TSTATCCPRH01 CONTRACTOR: Certified Air Contractors Jacksonville, Florida DATE: October 7, 2004 HEAT PUMP SYSTEM SUBMITTAL DATA QUANTITY: 1 UNIT NUMBER: AHU/CU-7 FAN COIL MODEL: FV4BNB003000 CONDENSING UNIT MODEL: 38YDBO36---3 PERFORMANCE DATA CFM 1208 EAT DRY BULB 79 ° E S P 0.53 EAT WET BULB 65.8 ° MOTOR HP 1/2 AMBIENT DRY BULB 95 ° BTUH TOTAL COOL 34.5 INTEGRATED HEAT 31.3(@47) ° NET CAPACITIES BTUH SENSIBLE COOL 26.6 SEER 15.0 C.O.P. 3.52 H.S.P.F. 8.5 ELECTRICAL DATA FAN COIL W/ 6.8 K.W. OF ELECTRIC HEAT @ 208V CONDENSING UNIT VOLTS/PHASE 208/1/60 VOLTS/PHASE 208/1/60 F.L.A. MOTOR AMPS 4.3 MIN. CIRCUIT AMPS 18.5 HEATER AMPS 32.8 @ 208/1 MOCP 30 MIN. CIRCUIT AMPS 49.5 @ 208/1 FUSE AMPS 50 ACCESSORIES: Electrical Disconnects & Fire/Life Safety BY OTHERS. Fixed Speed Ahu is not an option with 38YDB Series Units Fan Rated at High Speed Excel/VV _ HEAT PUMP SYSTEM SUBMITTAL DATA QUANTITY: 1 UNIT NUMBER: AHU/CU-8 FAN COIL MODEL: FV4131413006000 CONDENSING UNIT MODEL: 38YDBO48---3 PERFORMANCE DATA CFM 1610 EAT DRY BULB 78.4 ° E S P 0.61 EAT WET BULB 65.9 ° MOTOR HP 3/4 AMBIENT DRY BULB 95 ° BTUH TOTAL COOL 46.9 INTEGRATED HEAT 42.4 (@47) ° NET CAPACITIES BTUH SENSIBLE COOL 35.9 SEER 14.5 C.O.P. 3.72 H.S.P.F. 9.0 ELECTRICAL DATA FAN COIL W/ 7.5 K.W. OF ELECTRIC HEAT @ 208V CONDENSING UNIT VOLTS/PHASE 208/1/60 VOLTS/PHASE 208/1/60 F.L.A. MOTOR AMPS 4.3 MIN. CIRCUIT AMPS 18.5 HEATER AMPS 32.8 @ 208/1 MOCP 30 MIN. CIRCUIT AMPS 49.5 @ 208/1 FUSE AMPS 50 ACCESSORIES: Electrical Disconnects & Fire/Life Safety BY OTHERS. Sen Rosenborou h approved use of 7.5kw on AHU-8 - Carrier Contact is Louis Finklehoff Fixed Speed Ahu is not an option with 38YDB Series Units n Rated at High Speed xce _ HEAT PUMP SYSTEM SUBMITTAL DATA QUANTITY: 1 UNIT NUMBER: AHU/CU-9 FAN COIL MODEL: FK41)NF001000 CONDENSING UNIT MODEL: 38BYCO24 PERFORMANCE DATA CFM 698 EAT DRY BULB 81.9 E S P 0.72 EAT WET BULB 68.3 MOTOR HP 1/2 AMBIENT DRY BULB 95 ° BTUH TOTAL COOL 23.5 INTEGRATED HEAT 22.8 (@47) ° NET CAPACITIES BTUH SENSIBLE COOL 15.6 SEER 13.0 C.O.P. 3.46 H.S.P.F. 7.8 ELECTRICAL DATA FAN COIL W/ 3.8 K.W. OF ELECTRIC HEAT @ 208V CONDENSING UNIT VOLTS/PHASE 208/1/60 VOLTS/PHASE 20811/60 F.L.A. MOTOR AMPS 5.4 MIN. CIRCUIT AMPS 16.1 HEATER AMPS 18.1 MOCP 25 MIN. CIRCUIT AMPS 26.0 FUSE AMPS 30 ACCESSORIES: Electrical Disconnects & Fire/Life Safety BY OTHERS. Ben Rosenborou h approved use of 3.8kw on AHU-8 - Carrier Contact is Louis Finklehoff Fan Rated at High Speed xce _ Product InfinityTM 17 Data 38YDB (60 Hz) ' Two-Speed Heat Pump HEATING&COOLING with Puron° Refrigerant Sizes 024, 036, 037, 048, and 060 Model 38YDB InfinityTM Heat Pump incorporates innovative two-speed com- pressor technology with Puron®,refrig- erant for today and the future,providing quiet,efficient cooling performance. Built into these units are features most desired by homeowners today,including SEER ratings up to 17.0 and HSPF of 9.5 when matched with a VARIABLE SPEED indoor Carrier product.All models are listed with UL(U.S.and Canada),ARI,and CEC.The 38YDB exceeds the Energy Star®requirements for energy efficiency. FEATURES/BENEFITS Electrical Range—All units are offered in 208/230v single phase.Simpli- 0 0 a fied field-stripped lead wire connections facilitate ease of installation. Range of Sizes—Available in 5 nomi- nal sizes:024,036,037,048,and 060 to meet the needs of residential applications. Carrier's InfinityTM Controls— Ton These industry-leading controls,when installed with Carrier's Ideal HumidityTM variable-speed furnaces or fan coils, provide the homeowner with: –unparalleled control of temperature, humidity,indoor air quality,and zoning –unprecedented ease of use –simple operation through on-screen, 0text-based service reminders 0 0 –worry-free equipment malfunction alert on the two-speed outdoor section Optional remote access through telephone or Internet is also available when combined with a remote connectivity kit. WeatherArmorTM III Protection Package—This three-part protection sys- tem begins with the galvanized steel cabi- net.Once coated with a layer of zinc phosphate,a modified polyester powder coating is then applied and baked on,pro- viding each unit with a hard,smooth finish that will last for many years.Additionally, INFINITY' SERIES the coil protector,made of a coated steel wire grid with vertical 3/8 in.spacing,is designed to help protect the coil from Copyright 2004 Carrier Corporation Form 38YDB-4PD inclement weather,vandalism and inci- be made quickly and easily.Each valve has and maximum energy savings,it is recom- dental damage.It provides protection a service port for ease of checking operat- mended that you use variable speed indoor while not restricting airflow and maintain- ing refrigerant pressures. blower technologies.See product data ,.ing ease of coil cleaning.Finally,all Easy Serviceability—Removal of digest for CFM requirements for low-speed screws on cabinet exterior are ceramic access panel and control box cover capacity and high-speed capacity operation. coated for a long-lasting,rust-resistant, provides easy access to all electrical con- If your CFM is higher than the required quality appearance.. trols and compressor.Removal of top pro- CFM for low-speed capacity operation,you Unit Design—The coil incorporates vides access to fan motor and coil. may have little latent heat removal,result- copper tubing and enhanced,aluminum fins A self-diagnostic indicator on the ing in lower comfort levels in high humid- for optimum heat transfer.Hot condenser electronic control board informs the service ity climates.If your climate is hot with little air and sound are discharged vertically and technician of the failed component to no humidity,this mode of operation may away from adjacent patio areas and foliage. Compressor Protection—The com- be desired. Polymer spacers raise the coil in a heat pressor is protected with an internal over- Compressor Start Assist—Capacitor pump style basepan for easy removal of load.An internal pressure relief valve and relay is factory supplied. water,dirt,and debris. provides high-pressure protection to the Thermostatic Expansion Valve—This The 037 size includes an electronic ECM refrigerant system. unit must be installed with a Puron-refriger- condenser fan motor that provides multi- Standard Features—An electronic ant TXV on the indoor coil.The FV4 or speed operation and enhanced low-speed control eliminates excessive wiring.A com- FE4 indoor fan coils and CKSP indoor efficiencies and sound levels. pressor sound hood and discharge muffler furnace coils are factory equipped with a Auto-reset high-and low-pressure provide improved sound levels as well as bi-flow,balanced port Puron-refrigerant switches continuously monitor system sound quality on board diagnostics. TXV.When installed in this application,no operation. Important-When selecting an indoor further change is required.If any other A compressor crankcase heater,ener- blower section to be installed with the two- indoor fan coil or furnace coil is used,a gized during the compressor off cycle, speed unit,variable speed indoor blower balanced-port Puron-refrigerant TXV must helps to provide reliable starting. technology is recommended.Some 5-speed be installed.See accessory list in this Application Versatility—This unit can tap PSC motor products can be applied but publication for part number for your be combined with a wide variety of evapo- detailed engineering of the total system application.The 037 size only is factory rator coils,fan coils,and furnaces to pro- static pressure is required.Very few 4-speed equipped with a Puron-refrigerant,hard vide quiet,dependable comfort.Unit can be tap PSC indoor motor products can be shutoff balanced-portTXV. installed on a roof or at ground level on a installed with the two-speed unit.It is Limited Warranty—Five-year limited slab. important to match CFM for high-speed warranty on all parts and a 10-year war- External Service Valves—Both capacity and low-speed capacity as stated in ranty on the compressor.Refer to warranty service valves are brass,back seating type the combination rating tables.To derive all certificate for specific details. with sweat connections.Valves are exter- the benefits of improved room humidity nally located so refrigerant connections can and temperature control,lower noise levels, Model number nomenclature 38YDB 036 3 1 1 2-Speed Electric Heat Pump Series Packaging Nominal Capacity 037—37,000 Btuh 024—24,000 Btuh 048—48,000 Btuh Electrical 036—36,000 Btuh 060—60,000 Btuh 3—208/230-1 CERTIFICATION APPLIES ONLY WHEN THE ger Cor COMPLETE SYSTEM APPROVALS IS LISTED WITH ARI. U ISO 9001 aMa EN 29001 • t• �� BS 5750 PART i C QR L U S /SC) \29,5P 1 ANSI/ASOC 091 * As an ENERGY STAR* 9001 RIP CERTIFICATE NO.FM 28768 Partner,Carrier Corporation has determined that this REGISTERED QUALITY SYSTEM product meets the ENERGY STAR-guidelines for energy efficiency. 'Refer to the combination ratings in the Product Data Digest for system combinations meeting ENERGY STAR®efficiency standards. 2 Physical data 1 1 UNIT SIZE-SERIES 024-31 036-31 037-31 �2�83 �32�8 OPERATING WEIGHT(Lb) 187 243 292 REFRIGERANT Puron®(R-410A) TXV Cooling Control 6 Charge(Lb) .1 10.0 14.9 13.9 15. CONDENSER FAN Propeller Type,Direct Drive Vertical Air Discharge 1500 2500 2750 3000 3100 Air City(CFM) 1/15 1/8 1/5 1/5 1/5 Motor HP 825 825 Motor RPM 825 825 8401 COIL Copper Tube,Aluminum Plate Fin CONDENSER 10.8 18.2 18.2 18.2 182 Face Area C IL Fins per in. 1 20 20 20 22 Rows 1 2 2 2 3 S 5 5 Circuits 2 Sweat VALVE CONNECT.(In.ID) Vapor 5/8 I 3/4 I 7/8 I 7/8 I 7/8 3/8 Liquid REFRIG TUBES'(In.OD) 5/8 I 3/4 I 7/8 I 7/8 I 1-1/8 Vapor 3/8 Liquid LONG LINE REFRIGERANT TUBES(In.OD) 3/4 I 7/8 I 7/8 7/8 I 1-1/8 Vapor 3/8 Liquid NOTE:See unit installation instructions for proper installation. `Tube sizes are for runs up to 50 ft.Standard long line–up to 175 ft. t High Speed Accessories ORDERING DESCRIPTION NO. KAACF0801MED Coastal Filter—AII sizes KSASF0101AAA Support Feet(4) KHALS040I LLS Kit Solenoid Valve—All sizes KHASS0106MPK Snow Stand Kit—Size 024 KHASS0206MPK Snow Stand Kit—Sizes 036–060 KHAPX0201CPA Piston Kit—Required in some combination of 036 and 048 models.See description. KSATX0201 PUR Thermostatic Expansion Valve Kit—Size 024 KSATX0301 PUR Thermostatic Expansion Valve Kit—Sizes 036 and 037 KSATX0401 PUR Thermostatic Expansion Valve Kit—Size 048 KSATX0501 PUR Thermostatic Expansion Valve Kit—Size 060 KHAPG0101 PGS Pressure Guard Kit—Sizes 024,037 and 048 KHAPG0201 PGS Pressure Guard Kit—Sizes 036 and 060 THERMOSTAT/SUBBASE PKG DESCRIPTION TSTATCCPRH01-8 ThermidistatTM Control—Non-Programmable/ProgrammableThermostat with Humidity Control Carrier Thermostat,Auto Changeover,7-Day Programmable,°F/°C,2-Stage Heat/2-Stage Cool in AC TSTATCCP2S01-B Mode,3-Stage Heat/2-Stage Cool in HP mode Carrier Thermostat,Auto Changeover,Non-Programmable,°FrC,2-Stage Heat/2-Stage Cool in AC TSTATCCN2S01-B Mode,3-Stage HeaU2-Sta a Cool in HP mode TSTATXXSEN01-B Outdoor Temperature Sensor TSTATXXNBP01 Backplate for Non-P rog ramm able Thermostat TSTATXXPBP01 Backplate for Programmable Thermostat TSTATXXCNV10 Thermostat Conversion Kit(4 to 5 Wire)—10 Pack INFINITYT""CONTROLS DESCRIPTION SYSTXCCUID01 Infinity Control Deluxe 7-Day Programmable(Wall-mounted system control.) SYSTXCCUIZ01 Z Infinity Zone Control Deluxe Zoning 7-Day Programmable(Wall-mounted control for a multi-zone system.) SYSTXCC4ZC01 N Infinity 4-Zone Damper Control Module(Wall-mounted control for a four-zone system.) I Infinity Smart Sensor(Optional wall control used to monitor temperature and/or fan control in an SYSTXCCSMS01 N Individual zone.) SYSTXCCRRS01 G Infinity Remote Room Sensor(Monitors temperature in an individual zone.) SYSTXCCSAM01 Infinity System Access Module(Hardware for wireless access and control via phone or internet.) Infinity Network Interface Module(Connects Heat Recovery and Energy Recovery Ventilators or older two SYSTXCCNIM01t I outdoor models to system.) SYSTXXXBPU01 I Decorative Back Plate for Infinity Control(Decorative wall plate.) When applied with Carrier's IdealHumidityTM series 58MVP,58CVA and FE Indoor Models. 3 t Must be installed in Dual-Fuel Infinity system applications. Electrical data MIN MAX UNIT OPER VOLTS` COMPR WIRE LENGTH MAX FUSE**OR SIZE- FAN SIZEt (Ft)$ CKT BKR SERIES V/PH Max Min LRA RLA FLA MCA 60oCf75°C 60oCf75°C AMPS 024-31 64.0 10.6 0.5 13.8 14/14 57/55 20 036-31 66.0 14.1 0.8 18.5 14/14 43/41 30 037-31 208/230-1 253 187 66.0 16.8 0.5 21.5 12/12 158/55 30 048-31 96.0 22.3 1.1 29.0 10/10 69/66 45 060-32 130.0 28.3 1.1 36.5 8/8 85/81 60 Permissible limits of the voltage range at which unit will operate sat- FLA - Full Load Amps isfactorily. LRA - Locked Rotor Amps t If wire is applied at ambient greater than 30°C(86°F),consult Table MCA - Minimum Circuit Amps 310-16 of the NEC(ANSI/NFPA 70).The ampacity of nonmetallic- RLA - Rated Load Amps sheathed cable(NM),trade name ROMEX,shall be that of 60°C (140°F)conductors,per the NEC(ANSI/NFPA 70)Article 336-26.If NOTES: 1. Control circuit is 24-v on all units and requires external other than uncoated(non-plated),60 or 75'C(140 or 167°F)insula- power source. tion,copper wire(solid wire for 10 AWG and smaller,stranded wire 2. Copper wire must be used from service disconnect to unit. for larger than 10 AWG)is used,consult applicable tables of the NEC 3. All motors and compressors contain internal overload pro- (ANSI/NFPA 70). tection. $ Length shown is as measured 1 way along wire path between unit and service panel for voltage drop not to exceed 2%. " Time-delay fuse. CHARGING SUBCOOLING* (TXV TYPE EXPANSION DEVICE) UNIT SIZE HIGH 024 15 036 13 037 12 048 11 060 13 'Charge in high speed only. A-weighted sound power (dBA) UNIT STANDARD TYPICAL OCTAVE BAND SPECTRUM(without tone adjustment) SIZE RATING' 125 250 1 500 1000 2000 4000 8000 HIGH SPEED 024 74 52.9 58.4 58.8 68.5 57.7 53.0 45.4 036 74 53.9 59.4 60.8 65.5 58.7 53.5 48.4 037 74 49.4 60.4 66.3 67.5 59.2 56.0 50.4 048 75 53.9 59.9 59.8 63.0 60.7 53.5 48.9 060 76 54.9 63.4 59.8 67.0 60.7 57.0 49.9 'Sound is equivalent at high and low speeds. NOTE:Tested in accordance with ARI Standard 270.95.(Not listed with ARI.) 5 Dimensions ■ k — - § �,2 _ §d g2§ »® §kw § § \ § ( go z � � ) ) ) ) k e _ ) 10'.} ] �� . - ~ � \ \ \ =ate Q §j! § f \22 D( / � � « } \ 2 <- (; uj � f §j k � iF §\ 0 - z / @ ( ) @ eeee . 2 = co < _ _ § o@@ ® @ \ 2 § $ mamas to CL � � � » § tU.777 / E k § Q � ° 2 � � � CO� { k z w \ # 377 \ 7 \ § 7 [ & ¥ , & & & & £2 EB _ "T y4k « ) 104 c § ± _ 6 cd ° ° _ ° U) \«� u ? ) § § § � 2 [ / ] Lu )r ca © � \§\ � > . 2§egtoakk£k- « �)� o§� o)oo)« R. 0 mEc / ® © i o0 » . 8b ` )� © © / 0 0 � ] £ E ] = Cl) :3 - I _ K § § § § a 1E2 - � fLZ � 2 § { \ / A - �k LU V. LO -j .k§ § / § 2 § z I < } ƒ � / <0 < } 6 Guide specifications Air-Cooled, Split-System Heat Pump 38YDB 1-1/2 to 5 Tons Nominal GENERAL System Description Condenser fan motors will be totally enclosed,1-phase type with class B insulation and permanently lubricated bearings. Outdoor-mounted, air-cooled,split-system heat pump unit Shafts will be corrosion resistant. suitable for ground or rooftop installation.Unit consists of a hermetic compressor,an air-cooled coil,propeller-type Fan blades will be statically and dynamically balanced. condenser fan,and a control box.Unit will discharge supply Condenser fan openings will be equipped with steel wire air upward as shown on contract drawings.Unit will be used safety guards. in a refrigeration circuit to match up to a packaged fan coil or Compressor coil unit. Compressor will be hermetically sealed. Quality Assurance Unit will be rated in accordance with the latest edition of Compressor will be mounted on rubber vibration isolators. ARI Standard 240. Condenser Coil Unit will be certified for capacity and efficiency,and listed Condenser coil will be air cooled. in the latest ARI directory. Coil will be constructed of aluminum fins mechanically Unit construction will comply with latest edition of ANSI/ bonded to copper tubes which are then cleaned,dehydrated, ASHRAE and with NEC. and sealed. Unit will be constructed in accordance with UL standards Refrigeration Components and will carry the UL label of approval. Unit will have C-UL Refrigeration circuit components will include liquid tube approval. shutoff valve with sweat connections,suction tube shutoff Unit cabinet will be capable of withstanding Federal Test valves with sweat connections,system charge of Puron® Method Standard No. 141 (Method 6061)500-hr salt spray refrigerant,POE compressor oil,accumulator,and reversing test. valve. Air-cooled condenser coils will be leak tested at 217 psig Operating Characteristics and pressure tested at 450 psig. The capacity of the unit will meet or exceed Btuh at a Delivery,Storage,and Handling suction temperature of OF.The power consumption at Unit will be shipped as single package only and is stored full load will not exceed kW. and handled per unit manufacturer's recommendations. Combination of the unit and the evaporator or fan coil unit Warranty(for inclusion by specifying engineer) will have a total net cooling capacity of Btuh or greater at conditions of T CFM entering air temperature at the U.S.and Canada only. evaporator at OF wet bulb and OF dry bulb,and air entering the unit at OF. PRODUCTS The system will have a SEER of Btuh/watt or greater Equipment at DOE conditions. Factory assembled,single piece,air-cooled heat pump unit. Electrical Requirements Contained within the unit enclosure will be all factory wiring, Nominal unit electrical characteristics will be v, piping,controls,compressor,refrigerant charge(Puron®),and phase,60 hz.The unit will be capable of satisfactory special features required prior to field start-up. operation within voltage limits of v to v. Unit Cabinet Unit electrical power will be single point connection. Unit cabinet will be constructed of galvanized steel, Control circuit will be 24v. bonderized,and coated with a powder coat paint. Special Features Fans Refer to section of this literature identifying accessories and Condenser fan will be direct-drive propeller type, descriptions for specific features and available enhancements. discharging air upward. Carrier Copyright 2004 Carrier Corporation•Indianapolis,IN 46231 4-04 A United Technologies Company Manufacturer reserves the right to discontinue,or change at any time,specifications or designs without notice and without Incurring obligations. Book 1 1 2 1 4 Page 64 Catalog No.523-80124 Printed in U.S.A. PC 101 Form 38YDB-4PD Tab 3a I 1a I 2a Replaces:38YDB-3PD Product FV46 Data Direct Expansion �arrie Variable Speed Fan Coil HEATING&COOLING Puron® Refrigerant Sizes 002 thru 006 Premium Environmentally Sound Fan Coil The latest in technology makes the FV4B the most advanced air handler available.With attention to quiet, efficient,and comfortable operation, Carrier has developed a new benchmark for Indoor Weather control. Carrier's heat pump and air conditioning systems now feature Puron®(R-410A),the chlorine-free refrigerant that is the future for the residential heating and cooling industry.The FV4B using Puron® maximizes performance for environmentally sound systems.In addition to environmental safety,these systems are 30 to 40 percent more efficient than standard heating and cooling systems,thereby combining excellence in efficiency and environmental safety. The FV4B provides these benefits o due to Carrier's command of ECM "Electronically Commutating Motor" ® technology.These motors are extremely efficient at all speeds,and enable the FV4B to operate at the correct speed to deliver airflow precisely,ensuring proper performance across a wide range of o duct static pressures.This adaptive efficiency also makes installation quality easier to achieve for today's demanding homeowner. Carrier's command of ECM p 0 technology may be most evident in the A02332 comfort advantages that ECM can ® deliver.Operation set up steps on the Easy SelectTM Board provide the installing technician with alternatives Puron® to maximize comfort and efficiency. For truly Custom Made Indoor Weather,the homeowner can achieve Copyright 2003 Carrier Corporation Form FV4B-3PD command of both temperature and face areas of the FV4B refrigerant quality installations the unit exterior humidity in cooling and heating coils also provide superior efficiency, for rims sweat refrigerant conand ons modes. for high SEER and HSPF P leak free performance, Another feature which sets the FV4B performance.Carrier leads the way in multiple electrical entry for both high apart is the factory-installed TXV, condensate control,a hallmark of these and low voltage service. which enhances efficiency and multipoise fan coils.All of these For superior technology and provides compressor-protecting featured components are protected unmatched comfort,the operation at all recommended within a rugged,prepainted metal environmentally sound and efficient conditions.Grooved copper tubing, cabinet lined with super thick,high FV413 can't be beat. louvered aluminum fins,and the large density insulation.For neat,high Features Environmentally Sound Refrigerant Technology • Puron,chlorine-free non-ozone depleting refrigerant • Thermostatic Expansion Valve(TXV)designed to maximize performance with Puron Energy Efficient Operation • Electronically Commutating Motor(ECM)operates efficiently at all speeds • Maximizes efficiency of heating and cooling systems • Ultra low power consumption during fan only operation Indoor Weather Control • Warm,comfortable heating air temperatures • Unmatched humidity control,especially with Carrier's ThermidistatTM Control Airflow and Sound Technology • Logarithmic spiral blower housings for high blower efficiency and quiet operation • Diffuser air discharge section for high airflow efficiency and quiet, smooth operation • High duct static capability • Unique cabinet design that meets new stringent regulations for air leakage.Meets requirements of a 2%cabinet leakage rate when tested at 1.0 inches of static pressure Condensate Control and Disposal Technology • Minimal standing water-less microbial growth for improved IAQ and reduced condensate line clogging and related condensate leakage Condensate fittings relocated away from turbulent airflow patterns at the blower entrance for improved condensate control performance • Overflow feature for slope coil units allows condensate to exit the unit without damage to product under clogged primary an secondary line conditions • Tested for condensate disposal at conditions much more severe than those required by ARI • Primary and secondary drain connections to comply with HUD • All pans constructed of an injection molded glass-filled polycarbonate engineering resin material,with brass drain connections. • High density,super thick cabinetry insulation with vapor barrier • Pre-painted galvanized sheet metal cabinet Heat Transfer Technology • Grooved copper tubing • Lanced sine wave aluminum fins • Discreet refined counterflow refrigerant circuitry • Bi-flow hard shut-off TXV metering device Quality Assisting,Ease of Installation and Service Features • All units multipoise • Provision made for suspending from roof or ceiling joints • Modular cabinet on 006 unit • Sweat connections for leak free service • Multiple electrical entry for application flexibility(high and low voltage) • Low voltage terminal strip,to safely hold connections within the cabinet • Inspection plate on A-coil models for quick coil cleanliness inspection • Cabinet construction features innovations designed to prevent cabinet sweating Controls and Electrical Features • Easy SelectTM Board to maximize comfort,efficiency,and safe heater airflow operation • Easy plug connection provided for quick installation of accessory heater packages • 40VA 208/230v transformer • Replaceable 5-amp blade-type auto fuse protects against transformer secondary short Filter Features • Factory supplied filter • Cleanable polyester filter me dia • Filter"springs"out for easy access-no tools required • Newly improved filter rack area-filter door insulation added for an improved air seal 2 Model number nomenclature F V 4 B N F 002 000 A A A A Fan Coil Variations Variations Premium Puron Multipoise I Series Series Variations Electrical— Heating Size 208/230/1 (kw) Size Designation F—Single Piece Cabinet,1-in.Thick Insulation 002 005 B—Both Modular and 1-in.Thick Insulation 003 006 Cor Gore�Qi VU �. Puron® COL US 9�01 MP2 REGISTERED CERTIFICATION APPLIES ONLY WHEN THE QUALITY COMPLETE SYSTEM IS LISTED WITH ARI. SYSTEM Physical data UNIT SIZE 002 003 005 006* SHIPPING WEIGHT(Lb) 135 150 172 207 REFRIGERANT Puron(R-410A) Metering Device TXV TXV SIZE 2-1/2 Ton 3 Ton 4 Ton 5 Ton COIL Type A Slope A A Rows—Finsfin. 3-14.5 Face Area(Sq Ft) 3.46 3.46 5.93 7.42 FAN Air Discharge Upflow,Downflow,Horizontal 525/470 700/ 630 875/ 785 1050/ 945 CFM(Nominal ClgMtg) 700/630 875/ 785 1050/ 945 1225/1100 875/785 1050/ 945 1225/1100 1400/1260 1050/945 1225/1100 1400/1260 1750/1575 MOTOR HP(ECM) 1/2 1/2 1/2 3/4 FILTER SIZE 21-1/2 X 16-3/8 21-1/2 X 19-7/8 21-1/2 X 19-7/8 21-1/2 X 23-5/16 Modular Unit 3 L : . | - ( - E w } G cm 2 y cli u I M ® ® ) ` ■ © m d 7 9 9 ) � \ � § . , &: © ■® � - k =f / \ \ § \ � � k � \ q ILL § / ] § § � � ƒ � § I � � 4 N N (7 N O Q m^ O Z x ^ N O N r _ © da J m 0 N N W N3 CD O ¢z 1 OW O x_ tiV O ;W � © ; ul E © o� O p go ' W - _ N CW t t2 N N Cl) 6 N ■ Wd ^S O d © LL tx � s AIRFLOW PERFORMANCE nwr► 1.3 \ 1 ► 1 \ 1 1 \ 1.2 : 1 \ 1 \ , 1 1 1 1 \ 1 • , 1 1 1.0 ' ► 1 1 \ 1 \ 1 0.9 1 i ► 1 ► ► 1 0.8- , ,_ _ ► \ _ 3 W oc ►' i I I \ LU 0.7— a I :i I F� I Q ' .'•:�I I 1 i 0.5-1, 1 I 0.4- 0.3 .4 1 •., . 1 ' I i' , a {` IL 1 i 1 :.P I 1 L' t.. I I 1 042 ........... ...r.. L-036--► '.-042—i Hi Cooling 1f024 4-030 1 , 0 500 600 700 800 900 1000 1100 1200 1300 1400 1500 SUM A01338 FV4BNF003 Nominal Cooling and Heat Pump Efficiency airflow for each size selection.Airflow can be adjusted+15%to—10% —-- — Nominal Heat Pump Comfort airflow for each size selection.Airflow can be adjusted+15%to—10% •—— • Maximum cooling airflow for largest size selection.Adjusted+15%from nominal. •••••• Fixed Duct Systems(See description on page 8.) 10 AIRFLOW PERFORMANCE 1.7 1 1 1 1 1 � 1.6 1 1 1 1 I 1 i I 1.5 I 1 1 ,\ 1 , ; :.: 1.4- 1.3- 1.2- 1.0- LU .4 1.3 1.0 w I . I 0.9- cc .9 a I I I 0.8- -J .8 J I I \ 0.6 0.5 I .•t. } 1 1 I I I I I I'•. I I•r' 1 0.3 I I I I•,..... 0.2 I I I ! :.: .......r ..... ' .........-• I .......f 0.1 . L.....• I 060 -i ..................��036 Vii-•042 1-048 i.--060 Hi Cooling I I 0 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 SCFM A013M FV4BNB006 Nominal Cooling and Heat Pump Efficiency airflow for each size selection.Airflow can be adjusted+15%to-10% ---- Nominal Heat Pump Comfort airflow for each size selection.Airflow can be adjusted+15%to-10% -•-• Maximum cooling airflow for largest size selection.Adjusted+15%from nominal. •••••• Fixed Duct Systems(See description on page 8.) 12 m 8 U d � N nN � W 2 U W v A O O O O 0� O Z C ¢� ° � I l l l l l l l l l l a l l � a I I I J n n n n W O { C` m O QN 3 N Oq m o N Y m m m m anD N i� m m O <N , A? o J N n R0. U I I I I I I I I I I I N c I I a �p I I I I N N N N �p m 22 U m $ a ca- N m> $ a he O d � d m O 1- H Y m n W S ¢>O 3 O O O O W r ° I I I I I i l l l l l a a l l a a I I I I °N> E _ 2-0 0 0 S UNe `y y Z N J 7 z S_ a s c VI V J o d c C7 e > H r 2 N� J � � N � W> �� W J ; N -y 0 m z a E z N m dr O o;, N U L O = E- 0 0 0 o h E c� C E 0a.` tl ty 3 d o 1'' U "' ° � I I I I I I 1 1 1 1 1 � � 1 1 � � I I I I � U; ♦ op 'p � N 7 C C to u1 U v) m m y O m (y Cl �y m 1� YNf m m N N U a'p p 0.0 J Y � � O O O O Cly �.j O W 1 1 1 1 1 1 1 1 1 1 1 g l l a a I I I I 3 N E w= c U 8 y V �'+ fy N c N g M' J N m Cl m N Y N ` III O OQQ QOQ O QO O O O m O O m IO N OOr�� r ��upOO�l AHD p I- Q� J � O U •; C L�• ��j � ` C�j 'aj C C £� Obi, (y ftp tem t�♦, I C7 t�• {ty7 Ip n t(Dy pad w W O' dam, �' GC L L_ LL L v N V O m m m m N N l�I m l7 Cl N N f� N m tC O N t� •� a; O N S N d Y LL p� CD w\ <t Q Q s m O m umi m umi 0 y� 01 W z� m m m m 0 m c m $ m pc m 9 3 a m� c m 10'0 6 U O O O U s O Ye O � S IL S z ° IL lL IL IL IL J m E C e LL L m z z z � z � zzzC1 U o N R N_ m m ug o „ ado 0 m tp W O) lOt NOO O T ` O M N Cl Cf S •N O Q 17 ��N �p NN 6 y y a� O N m N a N >j o N N tC E d tNO S N H Na N ' m y N l7 Cl Cl Hi �G m tC b Ih n m fV N �cnOm Ec � p po o p > m O^O C A ox mm � �V dm � �p.Y!°: mmm N o � j 38mEncc�^ at •f" ymd 4gz_ z z �_ _ % s >c �C�3LL Wiiiivl F" g N D N Z `m N r1 W W W W W W W 2 W W W 2 W W 2 S 2 F W S p U U U W U U W U U W W W W ` d d U O m m �+ IUL 4 u IUL W IL V W W U U W W U U U U W LL IUL IL ILSUa JSF, X Y Y Y Y Y Y Y Y Y Y Y Y ]t Y Y Y Y - 2 Y Y }�}� } }f• } +F: Z Z W 18 Product 38BYC (60 Hz) • Data Heat Pump HEATING&COOLING Sizes 018 thru 060 The 38BYC Outdoor Sections of Split-System Heat Pumps are designed for quiet,reliable heating during the winter and cooling during the summer.With a SEER of up to 14.0 and HSPF of up to 8.3,these heat pump systems provide economy of operation through energy conservation.They recover heat for indoor comfort from outdoor air during the heating season and,by automatically reversing the refrigerant system,remove indoor d o '"E heat and excess humidity during the o cooling season.All models are listed with UL(U.S. and Canada),CEC, and ARI. FEATURES/BENEFITS Electrical Range—All units are offered in single phase 208-230v. Size Range—38BYC is available in 7 nominal sizes from 018 through 060 to meet the needs of residential and light commercial applications. Compressor—This unit features a scroll compressor which is significantly more efficient than conventional compressors.Its simple design offers improved reliability. Each compressor is mounted on rubber isolators for additional sound reduction.For improved serviceability,all models are equipped with a compressor terminal plug. Continuous operation is approved down to–30°F(-34.4°C) in the heating mode and down to 55°F(12.8°C)in the cooling mode. (See heating and cooling performance tables.) Copyright 2003 Carrier Corporation Form 38BYC-6PD Built-in-Reliable Components— accessory list in this publication for aluminum fin and is designed for Includes a suction-tube accumulator correct part number. optimum heat transfer during heating that reduces the amount of liquid and cooling. The vertical air ,..refrigerant reaching the compressor, Discharge Muffler—Incorporated discharge carries the sound and .loss of charge switch,and an to minimize low frequency sound and air up and away from adjacent internal pressure relief valve for high- pressure pulsation generated by patio areas and foliage.The pressure protection. compressor discharge gas. condenser coil can be cleaned with a Defrost Control Board—Incorporates Weather-Protective Cabinet— common garden ho3e. a defrost relay,defrost timer,and low- Steel is protected with a galvanized External Service Valves—Both voltage terminations.The defrost coating and treated with a layer of service valves are brass,front seating control is a time/temperature zinc phosphate.A coat of modified type.Valves are externally located so initiation/termination control which polyester powder is then applied and refrigerant tube connections can includes 3 field-selectable time baked on,providing each unit with a be made quickly and easily with sweat periods of 30,50,and 90 minutes. hard, smooth finish that will last for field connections.Each Thermostatic Expansion many years. valve has a service port for ease of Valve(TXV)—This unit must be All screws on cabinet exterior are checking operating refrigerant installed with a TXV on the indoor coated for a long-lasting,rust- pressures. coil.The FC4 and FK4 indoor fan resistant,quality appearance. coils come factory equipped with a Limited Warranty—Standard 5-year bi-flow TXV.When installed in this Unit Design—All units are equipped limited warranty on parts,5-year application,no further change is with totally enclosed fan motors for limited warranty on compressor. required.If any other indoor fan coil greater reliability under rain and snow or furnace coil is used,an accessory conditions.The large,wraparound bi-flow TXV must be installed.See coil uses copper tube and enhanced Model number nomenclature 38BYC 018 3 3 1 Electric Heat Pump Packaging Series Nominal Capacity 018—18,000 Btuh 042—42,000 Btuh 024—24,000 Btuh 048—48,000 Btuh 030—30,000 Btuh 060—60,000 Btuh Electrical 036—36,000 Btuh 3—208-230-1 2 G�`i\et Corpo 17 BSI APPROVALS ISO 9001 U EN 29001 5750 PART 1 C 9 L u s O 9 r mmu�w R is \ �t. ANSI/ASOC 091 9001 M P2 CERTIFICATE NO.FM 28768 CERTIFICATION APPLIES ONLY WHEN THE REGISTERED QUALITY SYSTEM COMPLETE SYSTEM IS LISTED WITH ARI. As an ENERGY STAR® Partner,Carrier Corporation has determined that this product meets the ENERGY STAR®guide- lines for energy efficiency. -Refer to the combination ratings in the Product Data Digest for system combinations meeting ENERGY STAR®efficiency standards. Physical data I UNIT SIZE 018 1 024 030 036 1 042 1 048 1 060 OPERATING WT(Lb) 115 1 166 182 182 209 1 250 1 278 COMPRESSOR Manufacturer Copeland Type Scroll REFRIGERANT R-22 Control TXV Charge(Lb) @ 15 Ft 5.5 6.25 6.88 8.00 10.38 11.13 14.00 CONDENSER FAN Propeller Type,Direct Drive Air Discharge Vertical Air Oty(CFM) 1800 2800 2800 2800 2800 2800 3400 Motor RPM(60 Hz) 1100 825 825 825 825 825 1125 CONDENSER COIL Face Area(Sq ft) 12.4 14.93 18.5 '18.5 16.18 1 18.5 22.40 CONNECTION VALVE(In.ID) Sweat Liquid 5/8 3/4 3/4 3/4 7/8 7/8 7/8 Vapor 3/8 3/8 3/8 3/8 3/8 3/8 3/8 REFRIGERANT TUBES (In.OD) Vapor 5/8 3/4 3/4 3/4 7/8 1-1/8 1-1/8 Liquid 3/8 3/8 3/8 3/8 3/8 3/8 3/8 NOTE:See unit Installation Instructions for proper installation. METERING DEVICE UNIT OUTDOOR INDOOR SIZE SERIES PISTON TXV* 018 33,34 42 KSATX0601HSO 024 35,36 52 KSATX0601HSO 030 34,35 55 KSATX0601HSO 036 34,35 63 KSATX0601HSO 042 33,34 65 KSATX0601HSO 048 33,34 73 KSATX0701HSO 060 33.34 78 KSATX0701HSO TXV must be ordered separately when indoor coil is not equipped with a TXV.TXV is listed for any approved coil combination.All TXVs are bi-flaw,hard shutoff. 3 Electrical data MAX OPER VOLTS' COMPRESSOR MIN WIRE LENGTH MAX FUSEL UNIT V/PH FAN SIZE" (Ft) OR CKT SIZE-SERIES 60 Hz Max Min LRA RLA FLA MCA 60°C/75°C 60°C/75°C$ BKR AMPS 018-33,34 45.0 10.6 0.5 13.8 14/14 71/67 20 __--->024-35,36 54.0 12.0 1.1 16.1 14/14 60/57 25 030-34,35 72.5 16.7 1.1 22.0 12/12 71/67 30 036-34,35 208-230/1 253 197 88.0 17.8 1.1 23.4 12/12 66/63 35 042-33,34 104.0 23.2 1.1 30.1 8/10 104/63 50 048-33,34 137.0 23.9 1.1 31.0 8/10 124/76 45 060-33,34 148.0 32.1 1.4 41.5 6/8 156/88 60 Permissible limits of the voltage range at which unit will operate satisfactorily.Operation outside these limits may result in unit failure. t Time-delay fuse. t Length shown is as measured 1 way along the wire path between the unit and the service panel for voltage drop not to exceed 2%. •• If wire is applied at ambient greater than 30°C(86°F),consult Table 310-16 of the NEC(ANSI/NFPA 70).The ampacity of nonmetallic-sheathed cable(NM), trade name ROMEX,shall be that of 60°C(140°F)conductors,per the NEC(ANSI/NFPA 70)Article 336-26.If other than uncoated(non-plated),60°or 75°C (140°or 167°F)insulation,copper wire(solid wire for 10 AWG and smaller,stranded wire for larger than 10 AWG)is used,consult applicable tables of the NEC(ANSI/NFPA 70). FLA -Full Load Amps LRA -Locked Rotor Amps MCA -Minimum Circuit Amps RLA -Rated Load Amps NOTE:Control circuit is 24v on all units and requires external power source.Copper wire must be used from service disconnect to unit.All motors/compressors contain internal overload protection. Sound power UNIT SOUND LEVEL A-WEIGHTED SOUND POWER LEVELS(dBA)WITHIN OCTAVE BAND SHOWN SIZE-SERIES (dBA) 125 250 500 1000 2000 4000 8000 018-33,347E 69.5 68.0 68.0 69.5 61.0 58.0 57.0 024-35,367E 70.5 69.5 69.5 73.0 65.0 63.5 58.0 030-34,357f 71.5 71.5 70.5 72.0 65.0 62.0 59.0 036-34,3571 68.5 69.0 1 69.0 71.0 66.0 61.5 61.0 042-33,347 69.0 72.5 71.5 73.0 6 8.0 66.5 63.0 048-33,347 77.5 68.0 70.0 71.5 68.5 64.5 60.5 060-33,348q 74.5 73.5 74.5 74.0 72.0 69.0 65.0 NOTE:Tested in accordance with ARI Standard 270-95.(Not listed with ARI). 7 Dimensions N �.Z 5 a 2 cL 0 0 0 0 0 0 ?Z x x x x x x x N M MMM MMEMM 00 N Z d V V N N N N O a, .- '- J=o wQ < a v v v v v �) CL Jp O a3U O J =5 Q �Z QZ WJzp Z OZ N WMQZ O� z� Z n u7 chi 3Q� 7 UOZ w i W V V V Ch OO m0 J Z J _mz_ OZ?m �[ w t7 J �m 0 r W I;::-0 M 7 7 7 7 7M a a)V- LO O U) N a 2` OON O p � a E r `p 01 x O¢l O O (O (D <O (O (O O 0 C.- C O'-' N r�'8E w = rn 6 6 rn 6 rn a) w g p N UNC O N N N N N N N C7 Z o�ccy._ C ¢ 0 0 0 Z 0.—a) 7 g Q V a)C C CD 0�0 m � � a0 N N E w a)0 a)-75 0 Y n C? M c�+M cn M Q p U Ca E C cc t O N N N NN N ¢ ¢ O 0 a O ll Cl)U O a) Q N C C Go j O O'ro N .t.., ' cis 0 0 0 0 0 0 Q y_c yz d N �' N N N N N N 0 0 Q c M N COLE O CO 0 ^ r cc 8:9. 2 N O N'O� C "j IZ�I 20un 0) m a0 a0 m 20) C CS O O a)E N N N N N N N m M00077 olLNCO Q 3vEEL-E S-3 c2Ln a F Q �o�LnMm�EU 'Z � d) � � n r� n � O N N N N N N J Z N vi �!7 Y A m N N N N N N ¢ �{ LL U ¢ CD W so cD co co z x—� i 0 v a a w co co � _A U c� c� chi c� •- ,- Q ch m 6 ch cb r) W <O O <O O 10 CD fD wLC z 2 O 3 H W = M N Cl)MN N N M S0U ¢ W Y a N a p <�~ N cc 0 o 0 0 0 0 Y Q Q CV co M co M-Cl) M N 2 O N N M to N EaD �O�pp 7 h O O O O O O O Guide specifications Air-Cooled, Split-System Heat Pump 38BYC 1-1/2 to 5 Tons Nominal GENERAL System Description Condenser fan motors will be totally enclosed,1-phase type Outdoor-mounted,air-cooled,split-system heat pump unit with class B insulation and permanently lubricated bearings. suitable for ground or rooftop installation.Unit consists of a Shafts will be corrosion resistant. hermetic compressor,an air-cooled coil,propeller-type Fan blades will be statically and dynamically balanced. condenser fan,and a control box.Unit will discharge supply Condenser fan openings will be equipped with steel wire air upward as shown on contract drawings.Unit will be used safety guards. in a refrigeration circuit to match up to a packaged fan coil or Compressor coil unit. Compressor will be hermetically sealed. Quality Assurance Unit will be rated in accordance with the latest edition of Compressor will be mounted on rubber vibration isolators. ARI Standard 240. Condenser Coil Unit will be certified for capacity and efficiency,and listed Condenser coil will be air cooled. in the latest ARI directory. Coil will be constructed of aluminum fins mechanically Unit construction will comply with latest edition of ANSI/ bonded to copper tubes which are then cleaned,dehydrated, ASHRAE and with NEC. and sealed. Unit will be constructed in accordance with UL standards Refrigeration Components and will carry the UL label of approval. Unit will have C-UL Refrigeration circuit components will include liquid tube approval. shutoff valve with sweat connections,suction tube shutoff Unit cabinet will be capable of withstanding Federal Test valves with sweat connections,system charge of Puron® Method Standard No. 141 (Method 6061)500-hr salt spray refrigerant,POE compressor oil,accumulator,and reversing test. valve. Air-cooled condenser coils will be leak tested at 217 psig Operating Characteristics and pressure tested at 450 psig. The capacity of the unit will meet or exceed Btuh at a Delivery,Storage,and Handling suction temperature of °F.The power consumption at Unit will be shipped as single package only and is stored full load will not exceed kW. and handled per unit manufacturer's recommendations. Combination of the unit and the evaporator or fan coil unit Warranty(for inclusion by specifying engineer) will have a total net cooling capacity of Btuh or greater at conditions of CFM entering air temperature at the U.S.and Canada only. evaporator at °F wet bulb and °F dry bulb,and air entering the unit at °F. PRODUCTS The system will have an SEER of Btuh/watt or greater Equipment at DOE conditions. Factory assembled,single piece,air-cooled heat pump unit. Electrical Requirements Contained within the unit enclosure will be all factory wiring, Nominal unit electrical characteristics will be v, piping,controls,compressor,refrigerant charge(Puron®),and phase,60 hz.The unit will be capable of satisfactory special features required prior to field start-up. operation within voltage limits of v to V. _Unit Cabinet Unit electrical power will be single point connection. Unit cabinet will be constructed of galvanized steel, Control circuit will be 24v. bonderized,and coated with a powder coat paint. Special Features Fans Refer to section of this literature identifying accessories and Condenser fan will be direct-drive propeller type, descriptions for specific features and available enhancements. discharging air upward. Carrier Carrier Corporation•Indianapolis,IN 46231 06-03 A United Technologies Company Manufacturer reserves the right to discontinue,or change at any time,specifications or designs without notice and without Incurring obligations. Book 1 4 Page 32 Catalog No.523-801 o1 Printed in U.S.A. PC 101 Form 38BYC-6PD Tab 5a 5a Replaces:38BYC-5PD Product FK4D Data Direct Expansion ' Variable Speed Fan Coil HEATING&COOLING Sizes 001 thru 006 FK4D Premium Air Handling Technology The FK413 is the latest in air handling technology.It is the perfect unit when you need a fan coil that can deliver high-tech performance,application versatility,easy installation,and high efficiency. The FK413 achieves all this by taking full advantage of its programmable Electronically Commutating Motor (ECM).This versatile motor is completely static independent, meaning the motor will deliver the selected CFM regardless of the duct system,making it the perfect choice for both high and low static applications. Other features homeowners will appreciate are the FK413's soft ramp up when the unit is turned on,and its soft ramp down after the thermostat is satisfied.These features increase efficiency and eliminate the annoying sounds p^� associated with sudden changes in airflow.When the ECM is used in conjunction with specific indoor controls(such as the ThermidistatTM Control),the HVAC system can operate in comfort control modes like Super Dehumidify.This combination of Carrier products can offer unmatched comfort. ® The FK413 also features Carrier's patented `Easy SelectTM Board'This board streamlines installation and 0 helps the installer to select the correct A02332 airflow.The Easy Select Board combined with the ECM tru ly allows dealers to customize the heating and cooling system to each home. The FK413 is also loaded with the most advanced components, so you Copyright 2003 Carrier Corporation Form FK4D-3PD know it will perform like a premium high-impact,polycarbonate applications,the FK4D fits right where fan coil should.Inside you will find condensate pans.The primary and it is needed.It is equipped with sweat grooved copper tubing and lanced sine secondary drain connections include connections and has multiple electric ,.,.wave aluminum fins,which contribute brass inserts.All of this is packed in a entries for fast,simple installations. Lo the FK4D's high SEER and HSPF rugged,prepainted metal cabinet that Carrier also offers the FK4D with ratings. Carrier technology also is lined with super-thick,high-density field-installed,electric-resistance heat incorporates factory washed coils for insulation. Obviously a unit built kits in sizes 5-to 30-kw.When the superior condensate control,dedicated to last. ultimate in efficiency,comfort,and refrigerant circuitry,and state-of- In addition to superior quality,the durability is needed,the FK4D is the the-art Thermostatic Expansion FK4D also offers the ultimate in fan coil to use. Valve(TXV)refrigerant metering. versatility.Compact and designed for These units are also designed with upflow,downflow,and horizontal Features • Programmable ECM blower motor • Easy SelectTM Board • Grooved copper tube • Lanced sine wave aluminum fin • Discreet refrigerant circuits • Pre-painted galvanized sheet metal cabinet • Unique cabinet design that meets new stringent regulations for air leakage.Meets requirements of a 2%cabinet leakage rate when tested at 1.0 inches of static pressure • Cooling control in every unit • Static independent airflow • Logarithmic spiral blower housings for blower efficiency • High impact polycarbonate condensate pans • All units multipoise • Cabinet construction features innovations designed to prevent cabinet sweating • Provision made for suspending from roof or ceiling joists • Modular cabinet design on 006 size • Factory-supplied,cleanable,permanent framed filter • Easy access filter—no tools required • Field-installed heater packages 5- to 30-kw,fused,circuit breaker,non-fused(10-kw and down) • Low-voltage terminal block • AMP plug connection provided for accessory heater packages • Connections for humidistat/humidifier • Connections for air cleaner relay • Blower on/off-delay time selections • Extra thick 1-in.,R 4.2 high-density insulation • Newly improved filter rack area—filter door insulation added for an improved air seal • Tested for condensate disposal at conditions much more severe than those required by ARI • Sweat connections • Bi-flow hard shut-off TXV • Multiple electrical entry • Primary and secondary drain connections with brass inserts • Inspection plate on A-coil models • 1-1/2–5 ton application • HUD approved for manufactured housing • Replaceable 5-amp blade-type auto fuse protects against transformer secondary short • 40 va,208/230v transformer • All models listed with UL (U.S. and Canada)and ARI • Independent fan only selections 2 Model number nomenclature F K 4 D N F 002 000 A A A A Fan Coil Vanatons ICM Motor, High Efficiency Variations Multipoise Series Series Variations Electrical— Heating Size 208/230/1 (kw) Size Designation 001 005 F—High Density,1-in.Thick Insulation 002 006 B—Both Modular and 1-in.Thick insulation 003 `,.I COI 0,, U C o L uS L �. 59001 fFP2�0 REGISTERED CERTIFICATION APPLIES ONLY WHEN THE QUALITY SYSTEM COMPLETE SYSTEM IS LISTED WITH ARI. Physical data 4 UNIT SIZE 001 002 003 005 006' SHIPPING WEIGHT(Lb) 115 130 149 167 202 REFRIGERANT R-22 Metering Device TXVt TXV SIZE 3 Ton 3 Ton 5 Ton 5 Ton 5 Ton COIL Type Slope A Slope A A Rows—Fina/In. 3-14 Face Area(Sq Ft) 2.97 3.46 3.46 5.93 7.42 FAN Air Discharge pflow,Downflow,Horizontal 525/470 525/470 700/ 630 875/ 785 1050/ 945 CFM(Nominal Clg/Htg) 700/630 700/630 875/ 785 1050/ 945 1225/1100 875/785 875/785 1050/ 945 1225/1100 1400/1260 1050/945 1050/945 1225/1100 1400/1260 1750/1575 MOTOR HP(ECM) 1/2 1/2 1/2 1/2 3/4 FILTER SIZE 21-1/2 X 16-3/8 21-1/2 X 16-3/8 21-1/2 X 19-7/8 21-1/2 X 19-7/8 21-1/2 X 23-5/16 Modular Units t Fan coil units with TXV must have a start capacitor and relay for single-phase outdoor units with reciprocating compressor. See outdoor unit presale literature. 3 - -� ` = I I I I I } co J% ! I /%( E| w d ® ® G > > d 7 7 - - } ! $ A|! �| ; ~ . -( « - - ( m ® » > A (0 k / ® co LnLg » 2 § B - _ _ - 4 CN N - N £ 7 » &A A+ Ln c 31 2t6/ _ [ q: ® / § § § ®- i L-4 N o E LL � � .� � � � 4 0 N O Q ED - o © � �W �o O O O _ — NCL O m n N d J c2 ;1 O O vc En O 0 0 � _ d In aD V N O C Lo r r Lo Ln J — M CD 7 r N N c .oCO �x S A v O�d O f0 (O d a�D t 4S LL C r r N N N m Lo o Wd a�• g O ■� - & _y o f z LL O _ o =y a V ► =- - 4 I O -- d � s AIRFLOW PERFORMANCE 1 NOMINAL COOLING ———— NOMINAL HEATING , 0.9 ...f...... .. I ...._ 1 i ........ .......:'' 1 I I I \ I I I I 1 I I I 0.8 I I ..........._ I ! I 036 HI I t I I I COOLING 1 Ij 1 1 I tt�I I I 1 1 :• I 0.7- 0.6— UJ .7 0.6 1 1 l I j cc I I / WcrI i I IL U 0.5— Z .5 1 I I a I Q I I I •` W 1 :•' 1 1 I I's I I I I U1 0.4 1 I I I I I I I I I I I 0.3 J 1 I I i'••• I 0.2 I I I I ......... .................. .-"" 1� .•.-r"�•.. I ""•'tet ......... ............._ •: 1 1 ........_.........}......,:::_...............................r. �._---. ..........._._ .. 1 1-018- 1--024-• I I -.030-- I 036-- 0 400 500 600 700 800 900 1000 1100 1200 1300 SUM A02342 FK4DNF001 002 Nominal Cooling and Heat Pump Efficiency airflow for each size selection.Airflow can be adjusted+15%to—10% ———— Nominal Heat Pump Comfort airflow for each size selection.Airflow can be adjusted+15%to—10% —•— • Maximum cooling airflow for largest size selection.Adjusted+15%from nominal. •••••• Fixed Duct Systems(See description on page 8.) 9 0 U U U J I I I I I I I I I I I tld N I I ti N w c x c N u c o Wo p I I I I l l l l i m m I m I I I I z4 f Z E `5m d O nS N 3 S3 O O C10 10 amD m 100 1\0O m N m m m 0 m H <N m _ 2—m--ow O � m J m O I I I I I I I I I I N I I N a I I I I N 0 U < a U CL yU h J O N ro Re p 4 m> C O K Lp I�'N�I 11�h O N tOO t7 10\O t00 O [� O O N $ r �W/� f R 1J� V N Gi F}I LL 0 Zi w o 11 1 1 1 1 1 I I I I as I I ao I I I I a � U N U A ~ ¢0 3 0 0 0 0 m " 3N" p � 1 1 1 1 1 1 1 I I I I as I I as I I I I pNo 0 N N o o e O 2 =CCNS3 ISI Z_W a O t0 (n m � m mea a aaaaaaaaaa lad a laaaa r� N� x m ; a F J I I I I I l l l l l l a a I I a I I I I c� m m o z "> Ja � N> I I I I I I I 1 1 1 1 as I I 1 1 1 1 m L ¢ J _ 'Da l6 3 N s e ° E m m m m m f m m f $ m Ur v E gea a s a � aa � aa a I as I a � Ger NVa x a � Ul U O J Q 0 O 0 0 0 0 I I 11 9N I I S 1�IOO' I I I V � N N 0 > 3 d N O umm 0 d m u m m m ° 20 I7 m O _ M f f N m mlQ Iq I f m f O ^ O N Z < J �j fZE m m !•j m !h N U m N M N !7 f f O CN'1 N N r O N t� m f /O� m U a m 3 y ^ m r O O O O J h V U '0 4 U I� o ppo W a LL •m._ R o 0 0 0 j y V R�[ co InN �8"v 1 i I I I l l l l l l a a l l a a l l l t ' N 7 m 7 V w" p J P R F A a an d ac LL m o ■� S 0 0 0 0 0 o g o m o o m m m m a m N m� C N c_� Pv W „ L 4 m p 400 ap ap y l a l e ap� G=i a(pp a � c 2, Y� N f 1 G 0) Ol ID W N N . m Cf f7 N C9 Cn9 n N m d O <N N t7 T 3 C L LL L w, z _ = a ami a'; ro O Y/ J O O O N O d m 9 LL LL i�F m m m 3 m 3 m m 4 N m m N 3 m N N m m C C m J f •O ; m y c O p O O pp O O O O > > > m aIpp d U p ¢O 2 Z Z V U Z V Z Z 2 V LL V 2 2 IL U li LL LL LL J N 17 7 C C C O ca N L Ua E m m; cii N N O N t�0 m(CO O Y/ IL O N m 9p m m m O N fV Cl CI C'1 Cl IG IC tG IG 1� cq m N'r-.A = N t i= oo�a �-mg, ¢o z z z u z 8 z U LL u R ti C LL ¢ LL LL an d W¢ S S S S S x S 2 x N S x Ig ¢ d 01— LL LL O LL U S< W W W W W W W I W W 2 W W S S S S S C C ;LLL l0 LL U U U U U U U W U U W W U U W W W W F W W O O =VV` LL LL LL LL LL LL LL U W LL U U LL W U U U U Q Q U N �� N01 Y Y Y Y Y Y Y LL Y Y LL LL Y Y LL LL LL LL W LL LL U U y y Y Y Y Y Y Y S Y Y 32:2a_�d u aZ N mU LL L,+ U¢J S Lu LL } +I.: Z W 17 Product TSTAT Z- Data HEATING&COOLING Thermostats ThermidistatTM Control THERMIDISTAT: INDUSTRY LEADING DELUXE NON-PROGRAMMABLE TEMPERATURE PLUS HUMIDITY CONTROL THERMOSTATS PREMIUM PROGRAMMABLE THERMOSTATS STANDARD NON-PROGRAMMABLE 11 THERMOSTATS o �.. ` F-1 i� ® O "� 74 o e I 1 0 ,272 0 DELUXE PROGRAMMABLE THERMOSTATS ° UO 16:03- Efl F-- 68 �p v � ,•gum o Do ® ® ® ® LW BUILDERS STANDARD PROGRAMMABLE THERMOSTATS NON-PROGRAMMABLE THERMOSTAT O � 0 _• 72 O ,� i2 O O 0o17 Z� ® O O Copyright 2003 Carrier Corporation TSTAT-6PD The Carrier electronic thermostat PREMIUM PROGRAMMABLE overriding program schedule product line consists of programmable CONTROL FEATURES: -Outdoor temperature sensing and non-programmable air conditioner, .heat pump,and 2-speed models;a -Modes include OFF,COOL,HEAT, (Optional ) )rogrammable dual fuel model;and a AUTO,and EHEAT(emergency -Copy function for ease of programmable/non-programmable heat on heat pump models only) programming ThermidistatTl Control.Carrier also -Fan modes include ON and AUTO -Auxiliary heat lock-out(Heat pump offers builder's and standard -Equipment ON indicators and dual fuel models using outdoor programmable thermostats in both air -Auto changeover available on all sensor) conditioner and heat pump models. models(can be disabled) -Fan activation--automatic fan with These units feature non-mercury based electronic controls built into a subtle, -Liquid Crystal Display that displays heat(Optional for packaged units) slim plastic enclosure.They require no current room temperature at all -Residential installations eligible for battery back-up. times,and desired temperature/ financing through Retail Credit programming prompts upon Program FEATURES/BENEFITS demand -Room temperature sensor offset THERMIDISTAT CONTROL -Backlighting for LCD upon demand allows installer to deliberately The Thermidistat Control and include -Large,soft rubber pushbuttons with offset indoor room temperature to the above features plus: tactile action accommodate homeowner's needs. -One model for heating/cooling -Non-volatile memory to retain -Battery Free -Humidity display setting during a power outage -Humidify output for direct control -Two set points, 1 for heating and 1 DELUXE PROGRAMMABLE of humidifier settings for cooling CONTROL FEATURES: -Dehumidify output for variable- -Clean filter indicator(Time limit -Modes include OFF,COOL,HEAT, speed blowers adjustable) AUTO,and EHEAT(emergency -Vacation mode controls temperature -Auxiliary heat indicator(Heat pump heat on heat pump models only) and humidity while home is models only) -Fan modes include ON and AUTO unoccupied -Five minute compressor timeguard -Equipment ON indicators -Non-programmable set-up option -English/Metric(°F/°C)selection -Auto changeover available on all -Super Comfort Heat mode—when (Installer adjustable) models(can be disabled) applied with 40FKA or FK4C -Anticipator adjustment controls -Liquid Crystal Display that displays Comfort Heat Package sensitivity,cycles per hour current room temperature at all -Dual Fuel Compatible -Seven day programming,with 4 times,and desired temperature/ -Battery Free time periods per day programming prompts upon -Hold function for temporarily demand Model number nomenclature T STAT CC N AC 01 —B Series AC — Air Conditioning HP — Heat Pump Quantity 2S — Two Speed/Two Stage DF — Dual Fuel RH — Relative Humidity(Thermidistat Control) LH — Light Commerical Humidity S1 — Slim Line 1 day B—Builder's Model S7 — Slim Line 7 day S—Standard Programmable F1 — Flush Mount 1 day P—Programmable F7 — Flush Mount 7 day N—Non-Programmable CO — Cooling only R—Wireless Receiver HO — Heating only 2W— 2 Wire A/C and H/P BO — A/C&H/P No Program CC—Carrier Brand B1 — A/C&H/P 1 day 85 — A/C&H/P 5 day&2 day B7 — A/C&H/P 7 day EC — Reciever Thermostat RF — Wireless Sensor Q5 — 5+2 day Single Stage Heat&Cool QO — Single Stage Heat&Cool As an ENERGY STAR®Partner, Carrier Corporation has determined that the programmable thermostats and programmable Thermidistat Control meet the ENERGY STAR® guidelines for energy efficiency. 2 -Backlighting for LCD configurable -Available in 1-Day Programmable -Equipment ON indicators for always on operation configurations(Model# -Auto changeover available on all -Large,soft rubber pushbuttons with TSTATCCPB 101 models(can be disabled) tactile action -Liquid Crystal Display that displays -Non-volatile memory to retain DELUXE NOW current room temperature at all setting during a power outage PROGRAMMABLE CONTROL times,and desired temperature/ -Two set points, 1 for heating and 1 FEATURES programming prompts upon for cooling -Modes include OFF,COOL,HEAT, demand -Clean filter indicator(Time limit AUTO,and EHEAT(emergency -Backlighting for LCD configurable adjustable) heat on heat pump models only) for always on operation -Auxiliary heat indicator(Heat pump -Fan modes include ON and AUTO -Large,soft rubber pushbuttons with models only) -Equipment ON indicators -Five minute compressor timeguard -Auto changeover available on all -Non-volatile memory to retain -English/Metric(°F/°C)selection setting during a power outage (Installer adjustable) models(can be disabled) -Two set points, 1 for heating and 1 -Anticipator adjustment controls -Liquid Crystal Display that displays for cooling sensitivity,cycles per hour current room temperature at all -Clean filter indicator(Time limit -Seven day programming,with 4 times,and desired temperature/ adjustable) time periods per day programming prompts upon demand -Auxiliary heat indicator(Heat pump -Hold function for temporarily -Backlighting for LCD upon demand models only) overriding program schedule -Large,soft rubber pushbuttons with -Five minute compressor timeguard -Outdoor temperature sensing tactile action -English/Metric(°F/°C)selection (Optional) (Installer adjustable) -Copy function for ease of -Non-volatile memory to retain setting during a power outage -Anticipator adjustment controls programming sensitivity,cycles per hour -Auxiliary heat lock-out(Heat pump -Two set points, 1 for heating and 1 for cooling -Outdoor temperature sensing and dual fuel models using outdoor -Clean filter indicator(Time limit (Optional on all models except non- sensor) adjustable) programmable AC) -Fan activation--automatic fan with -Auxiliary heat indicator(Heat pump -Auxiliary heat lock-out(Heat pump heat(Optional for packaged units) models only) and dual fuel models using outdoor -Residential installations eligible for -Five minute compressor timeguard sensor) financing through Retail Credit -English/Metric(°F/°C)selection -Fan activation--automatic fan with Program (Installer adjustable) heat(Optional for packaged units) -Battery Free -Residential installations eligible for -Room temperature sensor offset -Anticipator adjustment controls sensitivity,cycles per hour financing through Retail Credit allows installer to deliberately Program -Outdoor temperature sensing offset indoor room temperature to (Optional on all models except non- -Room temperature sensor offset accommodate homeowner's needs. programmable AC) allows installer to deliberately -Available in 1-Day Programmable -Auxiliary heat lock-out(Heat pump offset indoor room temperature to configurations(Model# and dual fuel models using outdoor accommodate homeowner's needs. TSTATCCPS 101 or sensor) -Battery Free TSTATCCPF101 -Fan activation--automatic fan with heat(Optional for packaged units) BUILDERS NON- STANDARD PROGRAMMABLE -Residential installations eligible for PROGRAMMABLE CONTROL CONTROL FEATURES financing through Retail Credit FEATURES -Rubber push buttons with tactile Program -Rubber push buttons with tactile action -Room temperature sensor offset action -Modes include HEAT,OFF,and allows installer to deliberately -Modes include HEAT,OFF,and COOL offset indoor room temperature to COOL -Fan modes include AUTO and ON accommodate homeowner's needs. -Fan modes include AUTO and ON -Manual changeover -Battery Free -Manual changeover -Battery free -Battery free -Mercury free STANDARD NOW -Mercury free -English/Metric selection PROGRAMMABLE CONTROL -English/Metric selection -Temperature sensor offsets FEATURES -Temperature sensor offsets -Large display -Modes include OFF,COOL,HEAT, -Large display -Battery Free AUTO,and EHEAT(emergency -Power Stealing option available on -Power Stealing option available on heat on heat pump models only) AC models only AC models only -Fan modes include ON and AUTO 3 Dimensions IIIIIIIIIIIIIIIIIII Wireless Receiver un l V O R HEAT O COOL O FAN O 44" O�j 44 1.75' p POWER O —4.75'-1 L 7�Y 1 f--•4 1.75' 7 • Wireless Sensor Thermidistat Control Premium Programmable Thermsotat Coptrols 2.75•—�I @= Jtr 3.50 125' IT7 ❑ p00 la O ® O 5.51 37'j. Deluxe Programmable Thermostat Controls ------------- 3/4' ne 3/e' I i7� n A 31WF4 _ O O V 1 r �� 5 1h 1 �0.7 Standard Programmable Thermostat Controls 106• I.as' �2 A 314• 2 34' 5135e' ® --------------- _j . .. �41/4 Deluxe Non-Programmable Thermostat Controls Standard Non-Programmable Thermostat Control Builder's Model Thermostat Control 4 Product data information Physical Characteristics Aloft Premium, Deluxe,Standard Programmable;Deluxe,Standard Non-Programmable: Dimensions: See drawing Appearance:Plastic,eggshell color,textured Builder's/Standard Programmable Models: Dimensions: See drawing Appearance:Plastic,designer white,textured,white,grey rubber push buttons Electrical Characteristics Premium, Deluxe,Standard Programmable;Deluxe,Standard Non-Programmable: Input Volts/Amps:24vac,5 VA Builder's/Standard Programmable Models: Input Volts/Amps:24vac, 1 VA Environmental Requirements: Operating Temperature/Relative Humidity:32°F(0°C) to 104°F(40°C),95%rh non-condensing Storage Temperature/Relative Humidity:–40°F(-40°C)to 134°F(56°C),95%rh non-condensing Program Specifications: Premium,Deluxe Programmable Models: Temperature set point range:40°F(4°C)to 90°F(32°C) Separate heat and cool set points Auto changeover—can be disabled Clean filter reminder:installer adjustable Permanent memory Programming days:7 day Programming periods:4—Wake,Day,Eve,Sleep Hold function Copy previous day function w Humidity display and control(Thermidistat Control only) Equipment On indicator(Thermidistat Control only) Vacation Programming Standard Programmable Models: Temperature set point range:50°F(10°C)to 90°F(32°C) Manual changeover Non-volatile memory Fahrenheit or Celsius selectable Power-stealing option on AC model only Selectable fan ON or OFF with auxiliary heating(HP model) Five-minute compressor timeguard Four cycles per hour maximum Auxiliary heat LED on heat pump models 5&2 day programming Deluxe,Standard,Builder's Non-Programmable Models: Temperature set point range:40°F(4°C)to 90°F(32°C) Separate heat and cool set points Auto changeover—can be disabled Clean filter reminder:installer adjustable Permanent memory Equipment On indicator Wiring Requirements: Power:24vac nominal, 18-to 30-vac,50/60 Hz Wiring:Standard 18 to 22 gage. 5 Description THERMIDISTAT CONTROL PART NO. DESCRIPTION Thermidistat Control—Non-Programmable/Programmable Thermostat with Humidity Control. (For use in Dual Fuel, TSTATCCPRHI01-B AC,HP,and 2S applications. Includes Outdoor Air Temperature Sensor.) PREMIUM PROGRAMMABLE THERMOSTATS PART NO. DESCRIPTION TSTATCCPRF01 Thermostat,Auto Changeover,7-Day Programmable,°F/°C,Wireless Transmitter with range up to 500 ft. TSTATCCREC01 Wireless Receiver. TSTATCCPAC01-B Thermostat,Auto Changeover,7-Day Programmable,°F/"C,1-Stage Heat/1-Stage Cool TSTATCCPHP01-B Thermostat,Auto Changeover,7-Day Programmable,°F/°C,2-Stage Heat/1-Stage Cool Thermostat,Auto Changeover,7-Day Programmable,°F/°C,2-Stage Heat/2-Stage Cool in AC Mode, TSTATCCP2S01-B 3-Stage Heat/2-Stage Cool in HP Mode TSTATCCPDF01-B Dual Fuel Thermostat,Outdoor Temperature Sensor included DELUXE PROGRAMMABLE THERMOSTATS PART NO. DESCRIPTION TSTATCCPS101 Thermostat,Auto Changeover,single Day programmable,Slimline Style TSTATCCPS701 Thermostat,Auto Changeover,7-day programmable,Slimline Style TSTATCCPF101 Thermostat,Auto Changeover,single day programmable,Flushmount style TSTATCCPF701 Thermostat,Auto Changeover,7-day programmable,Flushmount style TSTACCP0501 Thermostat,Auto Changeover,7-day prog,Slimline Style STANDARD PROGRAMMABLE THERMOSTATS PART NO. DESCRIPTION TSTATCCSAC01 Thermostat,Manual Changeover,5-2 Day Programmable,°F/°C,1-Stage Heat/1-Stage Cool TSTATCCSHP01 Thermostat,Manual Changeover,5-2 Day Programmable,°F/°C,2-Stage Heat/1-Stage Cool TSTATCCPB101 Thermostat, Programmable,F/°C,simple 1 day programmable,T2 style TSTATCCPBS01 Thermostat,5+2 day programmable,Super T2 style,F/°C TSTATCCP2W01 Thermostat, Programmable,2-wire,7-day program schedule,Copy,Vacation,Super T2 style DELUXE NON-PROGRAMMABLE THERMOSTATS PART NO. DESCRIPTION TSTATCCNAC01-B Thermostat,Auto Changeover,Non-Programmable,°F/°C,1-Stage Heat/1-Stage Cool TSTATCCNHP01-B Thermostat,Auto Changeover,Non-Programmable,°F/°C,2-Stage Heat/1-Stage Cool STANDARD NON-PROGRAMMABLE THERMOSTATS PART NO. DESCRIPTION TSTATCCNB001 Thermostat,Non-programmable,F/°C,1-Stage Heat/1-Stage Cool,T2 style TSTATCCN2W01 Thermostat,Non-programmable,2-Wire,heat only or cool only,F/°C,T2 style TSTATCCN0001 Thermostat,Auto Changeover,N-P,°F/C°,1-Stage Heat/1-Stage Cool,battery or 5 wire BUILDERS NON-PROGRAMMABLE THERMOSTATS PART NO. DESCRIPTION TSTATCCBAC01-B Thermostat,Manual Changeover,Non-Programmable,°F/°C,1-Stage Heat/1-Stage Cool TSTATCCBHP01-B Thermostat,Manual Changeover,Non-Programmable,°F/°C,2-Stage Heat/1-Stage Cool 6 Thermostat accessories PART NO. DESCRIPTION TSTATXXSEN01-B* Outdoor Air Temperature Sensor TSTATXXNBP01t Backplate for Non-Programmable Thermostat TSTATXXPBP01t Backplate for Programmable Thermostat and Thermidistat Control TSTATXXBBP01t Backplate for Builde.'s Model Thermostat TSTATXXSBP01t Backplate for Standard Programmable Thermostat TSTATXXCNV10* Thermostat Conversion Kit(4 to 5 Wire)—10 Pack • Outdoor temperature sensor is an accessory for all Carrier electronic thermostats,except the non-programmable air conditioner version and builder's and Standard Programmable model thermostats.It allows the temperature at a remote location(outdoors)to be displayed on the thermostat. The outdoor air temperature sensor must be used with the dual fuel thermostat. The outdoor air temperature sensor is included with the Thermidistat Control and dual fuel thermostat. t This plate is designed to cover surrounding wall area located behind thermostat. t Thermostat conversion kit is a 24-vac accessory that can turn a 4-wire thermostat application into a 5-wire application.This kit can also be used to replace a broken thermostat wire,or add an extra wire when needed.Do not use this kit with the AC model of the Builder's or Standard Programmable thermostat. 7 Operational information Five-minute compressor timeguard This timer prevents the compressor from starting unless it has been off for at least 5 minutes.It can be defeated for 1 cycle by simultaneously pressing the FAN mode button and INCREASE TEMPERATURE(UP)button. Heat/Cool set points(desired temperature) A minimum difference of 2°is enforced between heating and cooling desired temperatures.This is done by allowing one setting to"push"the other,to maintain this difference.(Thermidistat Control is adjustable.)Builder's thermostats are controlled by a single set point. Equipment on indicators(Non-Programmable models) When cooling equipment is ON,a COOL ON icon is displayed above the room temperature display.When heating equipment is ON,a HEAT ON icon is displayed above the room temperature display. Equipment on indicators(Thermidistat Control) When cooling equipment is ON,a COOL icon preceded by a small triangle is displayed below the cool set point.While cooling equipment turn on is delayed by a staging or cycle timer,the triangle and the word COOL will flash.The same is true for the HEAT icon and its preceding triangle located under the heat set point.The 2 triangles are also used to indicate the state of the humidify and dehumidify outputs. See next section. Humidify/dehumidify output on indicators(Thermidistat Control) Within humidity select screen(selected by Humidity button and indicated by"hu"or"dhu"on clock display),the triangle under humidity set point will be on while humidify output is on.The triangle under dehumidify set point will be on while dehumidify output is active(turned off,because this output is reverse logic). Auto changeover When auto changeover mode is selected,a change from heat to cool(or vice versa)will not occur until an opposite mode demand has existed for 20 minutes.If set point is changed,the 20 minute requirement is deleted.Auto changeover mode can be disabled.Builder's and Standard Programmable thermostats are manual changeover. Emergency heat mode When thermostat is controlling a heat pump and emergency heat is selected,all Y signals are locked out,and W becomes energized upon a call for heat. Smart Recovery(Programmable models) With Smart Recovery selected,transition out of setback begins a fixed time period before selected recovery time and gradually adjusts room temperature so that the desired temperature will be achieved at selected recovery time. Room Temperature Offset(All models) Room temperature may be deliberately offset by up to 5°F in either direction. Maximum On/Off Deadband Maximum sensed temperature difference between ON and OFF is 0.8°F for Builder's thermostats and 0.6°F for all other models. Carrier Copyright 2003 Carrier Corporation•Indianapolis,IN 46231 4-03 A United Technologies Company Manufacturer reserves the right to discontinue,or change at any time,specifications or designs without notice and without Incurring obligations. Book 1 1 1 4 Page 8 Catalog No.02TS-TA6 Printed in U.S.A. PC 101 Form TSTAT-6PD Tab I mist I misc Replaces:TSTAT-5PD TLANTIC INSULATION, INC. 3525 IONIA STREET JACKSONVILLE, FLORIDA 32206 PHONE (904-354-2217) FAX (904-354-0129) PROJECT: Atlantic Beach City Hall Addition& Alteration SYSTEM: Condensate Drains Refrigerant Suction MANUFACTURER: Aeroflex USA, Inc. APPLICATION: Insulate with preformed, flexible unicellular pipe insulation. Secure with Aeroflex adhesive. Fittings shall be mitered sections of the same materials. Insulation located outdoors shall be finished with white protective coating. Insulation thickness shall be 1" for condensate drains and 1/4" for refrigerant suction. FINISH: Interior-Black Exterior- White APPLICABLE PARAGRAPHS: Section 15800 3.03, 3.04, � V „�•- SYSTEM: Concealed Ductwork MANUFACTURER: Knauf Fiberglass GEMCO Vimasco Mastic APPLICATION: Insulate concealed supply,return, outside air and general exhaust ductwork with 2.2”thick, 3/4# density, (R-6.0 installed )flexible fiberglass blanket with a factory applied foil scrim kraft vapor barrier jacket. Secure with outward clinching staples. Additionally secure with mechanical fasteners located 18" on center for ductwork over 24" in width. Seal all seams and joints with glass fabric and Vimasco 749 vapor barrier mastic. Necks of supply diffusers shall be insulated in the same manner if located in non return air plenums. FINISH: Foil Faced APPLICABLE PARAGRAPHS: Section 15800 3.05, SYSTEM: Exposed Ductwork MANUFACTURER: Knauf Fiberglass GEMCO Vimasco Mastics APPLICATION: Insulate supply, return and outside air ductwork with 11/2"thick, 3# density,rigid fiberglass board with a factory applied foil scrim kraft vapor barrier jacket. Secure with mechanical fasteners located 12" on center. Seal all seams and joints with glass fabric and Vimasco 749 vapor barrier mastic. FINISH: Foil Faced APPLICABLE PARAGRAPHS: Section 15800 3.05 i A .r \EIOJ EPm mus 11 closed cell elastomeric thermal insulation for HVAC & R Meets California Title 24 A6970, Sections 123 and 150. No painting required. General Uses -AMOCEC Tube and Sheet Insulation is a 'AEROCEC Pipe Insulation is used to retard flexible, closed cell and light weight EPDM" heat gain and control condensation drip from based elastomeric material designed for cold-water plumbing, chilled water, and insulating liquid cooling and heating lines. refrigeration lines. It also efficiently reduces 3/8", 1/2", 3/4" and 1" (10, 13, 19, and 25 heat flow for hot water plumbing and liquid mm) wall, in popular sizes up to 6" IPS. The heating and dual temperature piping. The closed-cell structure of Aerocel Pipe recommended temperature usage range for Insulation makes it an efficient insulation. Aerocel Pipe Insulation is -70 F to +257 F (-57 C to +125 C). Aerocel is manufactured to consistently provide actual values on these key performance criteria for mechanical system Resistance to Moisture Vapor Flow insulation: The closed-cell structure of Aerocel Insulation Thermal Conductivity: 0.25 effectively retards the flow of moisture vapor, : Water Vapor transmission: 0.10 and Aerocel is considered a low trans- ==" Fire Rating: Will not contribute significantly to mittance vapor retarder. Aerocel requires no fire (simulated end-use testing). supplemental vapor-retarder protection.' Aerocel Pipe Insulation, in 3/8", 1/2", 3/4" and 1" (10, 13, 19, and 25 mm) thicknesses has a flame spread rating of 25 or less and a smoke C � developed rating of 50 or less as tested by ,TY ASTM E 84 "Surface Burning Characteristics of Building Materials. Note: Numerical flammability ratings alone may not y t ,T� define the performance under actual fire conditions: ,-jai' - _ • They are provided only for use in the selection of=� � ` y products to meet limits specified. a II Key Features 4, �- • UV Resistant • Low thermal conductivity". }' " • Easy to install "' • • 25/50 rated " • Versatile, for heating;?, Refrigeration, plumb). aj:li' pppllcatlun -AEROCEL* Pipe Insulation in unslit tubular form can be slipped onto piping before it is ,nected, or it can be slit lengthwise and snapped over piping already connected. Butt joints and ns are to be sealed with contact adhesive; therefore, both surfaces to be joined are coated with adhesive. Aerocel is designed for installation above and below ground, indoor and outdoors. No protective finish is required. :ciflcatlons ESS** AEROCEL TEST METHOD !YSICAL PROPE ** LL STRUCTURE CLOSED CELL – 3-6(0.048 – 0.096) " ASTM D 1667 NSITY Lbs/ft' (am/cm') '7NDUCTIVITY L Mean 4°F 32 OF 75 OF 90°F 104°F ASTM C177 temp. (-20°C) (0°C) (24°CI (32 °C) (40°C) JIS A 1412 .lhr. °F K-value 0.22 0.23 0.25 0.26 027DIN 52613 (0.032) (0.034) (0.037) (0.038) (0.039) -70°F to 257°F AEROCEL becomes hard at-57°C, RVICE TEMP -57°C to+125°C but can be used even at-200°C J.V. Weather Resistance Excellent ASTM G-23 zone Resistance No cracking ASTM D 1171 ater Vapor Permeability 0.10 perm-in(0.15 x 10x'2) ASTM C355 E96 --- g/Pa.s.m) µz ioisture Resistance(µvalue) 5000 DIN 52615 Jater bsorotion Iweiaht %) S 5 ASTM D 1056 ,e bility ( % Shrinkage) 6 ASTM C534 JO°r 103°C)7 days Class V 0 UL-94 25/50 ASTM E84 iammability, Self extinguishing ASTM D 635 Class 1 G88624 131 (CHINA) moke Density Class 5.3 EMPA(Switzerland) Non Flammable JIS K 6911 pass IMO,**—and LLOYD registered Non corrosive DIN 1988 orrossion of copper, stainless litrosamine Contents"'""* Not detected U.S. FDA pound(reduction(0 L,,) 27 Db(20mm) DIN 52218 =lexibility excellent Continuous SS/PT Tubes Sheets Sheet Roll . AEROFLEX USA, INC. P. 9_ ALHAMBRA,CALIFORNIA 91803•PHONE:(323)728-2804•FAX:(323)728-0742•TOLL FREE:(866)AEROCEL• E-MAIL:sales@aeroflexusa.com•WEBSITE:www.aerotlexuse.com . � �EROSE AEROSEA�. Adhesive A� Q D for bondingQam= closed cell elastomeric insulation Description Properties ture range from +5 -C to +35°C. AEROSEAL is a Modified Neo- Appearance Black viscous liquid Avoid keeping AEROSEAL under prene Contact Adhesive specially Total Solids 22 ±2 % conditions that are out of the recom- formulated for bonding Aeroflex mended storage temperature range. Insulating Materials firmly together. Viscosity at 25°C 3,500-4,500 Also, ideal for use with other mate Health and Safety rials like Metal (painted/unpainted). Specific Gravity 0.88-0.90 Advisable to work in well ventilated Cork Board, Polyurethane Foam Rigid at 25°C areas to avoid inhalation of vapor from PVC Sheet, Formica, and Melamine Coverage (apply 130-180 Ftz/gallon solvents. Board and Rubber Sheet. adhesive both (3-4.5 MI/litre) The solvents contained in The high water vapor resistance surfaces) AEROSEAL are inflammable and and good weathering properties of Open -Time 5-10 minutes subjected tc legislation regulating their AEROSEAL can prevent water or storage and use. moisture from penetrating through Keep away from fire, and materials the joining points. Storage and Shelf Life which may cause fire such as paper, AEROSEAL is able to form a AEROSEAL can be preserved for at cloth, plastic etc. AEROSEAL strong, firm and permanent bonding least six months in well sealed contain- contents flammable liquid but dried between the applied materials ers. Recommended storage tempera- material is an self-extinguish adhesive. providing long lasting service. �.. Application 1. Surfaces of materials to apply _. W. should be dry, clean and free from dust, grit, oil, grease or any other loose materials 2 Stir AEROSEAL well before applying a thin and even coat of AEROSEAL onto both joining sur- faces by using a short hair brush, spreader or metal blade. 3. Allow solvents content of AEROSEAL to evaporate until the adhesive becomes dry to touch, but tacky, before)o ning the materials �! together normally 5-30 minutes. 4. Bona ny is possible vvithin 2 minutes atter application if used on --}' absorbent or permeable materials such as, Aeroflex Insulation, cork board and chipboard. A.. + If applied on non-absorbent or non- permeable materials like rubber or metal, a minimum of 5 minutes should be allowed to elapse before 4.--sac the surfaces can be bonded. -- . ' '" = ' .,;. 5 Press the surfaces to be bonded together under firm pressure. a C.. AICEPAS911105ENGLISH REPRINT 00 IWAIEE]35360VH° oAt l•. A14E (iA..1- EfD Ril.•OG i�Fi lLiFE,.X._;.1I()(NTEf,R.. N-..:1A-T!! IONAL CO. LTD. . 770 MU ti,TEPARAK RD..TEPARAK.SAAIUTPRAKARN W2/0 1HAILAND. TEL (66 2)383 6599 1 15 1-INES1 FAX (66 2)383 6531 383 6532 8656905695 AEROFLEX USA PAGE 01/01 1IER000,111 'Pu-e Acrylic Emulsion Pain Insulation : KNAUF DUCT WRAP Form No. AH-DS-5K Effective: 4/95 Supersedes: AH-DS-5J, Dated: 1/93 Submittal Date: DESCRIPTION MIL-1-24244C CONDENSATION CONTROL. Knauf Duct Wrap is a thermal and acousti- ASTM C 795 To determine thickness to prevent con- cal insulation blanket made from highly ASTM C 1136 Type II(FSK Facing)' densation at various ambient tempera- resilient, inorganic glass fibers bonded by ASTM C 1290 ture and humidity levels, based on a thermosetting resin. Knauf Duct Wrap In Canada: installed thickness 75%of nominal is available unfaced,with multi-purpose CGSB 51-GP-11 M (out-of-package)thickness,550F foil-scrim-kraft(FSK)or with a vinyl vapor CGSB 51-GP-52M,Type II(FSK Facing)" (13°C)air duct internal temperature: retarder.All vapor retarders have a 2" DND 15260-03 P-3 (51 mm)stapling flange on one edge. DND 15270-01 D-1 2 Factory application of the facing during DND 15270-02 D-2 1101 the manufacturing process assures DND 15280-01 E-1 !? (38mm, ( o. M RseqPuredhan 4 100 RequYed R•1�Y�) (76mm) YlriO uniform quality. DND 15280-03 E-3 , CCG Low FS Laminate Cert#GI-141 APPLICATIONS CAN 4-S102 90 Knauf Duct Wrap is used as external insula- 'Replaces HH-B-100B tion on commercial or residential heating or air conditioning ducts where operating tem- TECHNICAL DATA E None peratures range to+250'F(121°C)faced or • THERMAL EFFICIENCY. (ASTM C 177) 701 R'mm +350'F(177°C)unfaced.The product is suitable for application to the exterior of .12 40 w 60 70 60 so rectangular or round sheet metal ducts and — Relative NYmidtty% spaces or surfaces where temperatures SELECT MAXIMUM DCPECTED and condensation must be controlled. 1 --7.Z/ F RELATIVE HUMIDITY(RH)ON THE 0.9 LOWER SCALE. FEATURES & BENEFITS ° �3 MOVE UP VERTICALLY UNTIL • ENERGY CONSERVATION. THAT LINE INTERSECTS THE A low"K"factor significantly reduces EXPECTED MAXIMUM AMBIENT heat gain or loss when the insulation is AIR TEMPERATURE. applied with minimum compression. • SELECT THE THICKNESS INDICATED System efficiency is increased and fuel o BY THE INTERSECTION POINT. costs are decreased. • SURFACE BURNING CHARACTERISTICS. • LOW COST INSTALLATION. R-VALUES @ 75 F MEAN (UL/ULC LISTED) Knauf Duct Wrap is flexible and easily TEMPERATURE. Installed When tested in accordance with ASTM E conforms to flat or irregular surfaces.The Out-of- R-value 84, UL 723,CAN 4-S102, and NFPA lightweight rolls enable faster installation Package (at 25/0 R-Value Compression) 255, either unfaced or on a composite and lower labor costs in the field. .75 PCF 1'/�"(sa mm) 5.1 4.2 basis(insulation,facing and adhesive), • NOISE REDUCTION. (12 kgW) 2"(51 mm) 6.8 5.6 Knauf Duct Wrap does not exceed: Excellent acoustical properties 21&,"(56mm) 7.4 6.0 25 Flame spread effectively reduce sound transmission. 2'h"(64 mm) 8.5 7.0 50 Smoke developed • CONDENSATION CONTROL. 3"(76 mm) 10.2 _ 8.4 WATER VAPOR PERMEANCE. FSK faced Knauf Duct Wrap ensures 1.0 PCF 11h"(36 mm) 5.6 4.5 (ASTM E 96, PROCEDURE A) c densation control and helps prevent (16 kg/m°) 2"(51 mm) _7.4 _6.0 The multi-purpose FSK facing has a m�isture formation when properly 1.5 PCF 1'h"p8 mm) 6.1 4.8 maximum water vapor permeance of.02 installed and with sealed joints,seams (24 kg/ff?) 2"(51 mm) 8.2 6.4 perms.The vinyl facing has a maximum and penetrations. water vapor permeance of 1.3 perms. • DAMAGE RESISTANT. • TEMPERATURE RANGE. (ASTM C 411) • CORROSIVENESS. (ASTM C 665) Knauf Duct Wrap is tough and resilient Knauf Duct Wrap(faced)may be used Will not accelerate corrosion of a steel and resists damage in shipment, as well on ducts operating to+250°F(+121°C). test panel compared to sterile cotton. as during and after installation. Unfaced,the product can be used up to • MOLD GROWTH. (ASTM C 665) +350°F(+177'C). Does not promote the growth of fungi or SPECIFICATION COMPLIANCE . WATER VAPOR SORPTION. bacteria. Kna f Duct Wrap meets the requirements (ASTM C 1104) • PUNCTURE RESISTANCE. (ASTM D 781) of the following codes and specifications: Less than 5%by weight when tested for Multi-Purpose FSK-25 Beach units. ASTM C 553 Types I, 11, III 96 hours at+120'F(+49°C)and 95% HH-1-558C Type I, Class 7 relative humidity. NFPA 90A and 90B. NRC 1.36 Reg.Guide 1 I ?/2112002 15: 1.7 40784390179 GENERAL INSULATION PAGE 217-446.7900 FAX-217-443-2582 1'.O. BOX 846 SALES 800-331-1164 DNVII.L1, IL 61834-08445 SALES FAX-800-443-2561 11ts'dation Ila Vware-Adhesives-Srud►Melding Equipmeta Accessories INSULATION HANGER - PERFORATED ERASE (Adhesive Required) D - ----- -- -- - - - - :: C`� L _ _7) C SPECIFICATIONS ---- --------- MATERIAL 17INISI-I ,tp,t „T., NAIL: Carbon steel or NAIL: M.S. - Copper coated /aluminum � ALUM. - Norm 12 Gra. 3/4" to 28 ga. (.'105) 2„ 18" (.Q15-.G1 J} LA,E: Mild steel, (7-a Ga) 13AS11: Galvanized DESCRIPTION: GEMCO Peiforated Based Insulation Hangers are economical to Installl and one of the most universially accepted fastners used to install insualtion. Simply apply adhesive (Tuff-Bond Hanger Adhesvie) to the hack side of the Insulation Hanger and press int( place using a twisting (notion io assure an even spread of adhesvie. Allow the adliesive to cure for 24-48 hours(Drying limes vary with tomperalure) before attaching the insulation. Once the adhesive has dryed, it`'-`ale the insulation oil to the protrudir1(J. spindle Slid socllrle with a GEMCO Self-Locking Washer. FUr complete details and instructionslfor installing Insulation Hangers contact GEMCO or your nearest GEM%® distributor. ;-1I.)Itl(I:;1.1 1 1-- ;111. III 1 III1 A 2174,16 714o(.) P.O. DOX 846 SA LESF00-331-1164 Or'411fco ININVILLE, IL 018.34-0846 SAL)�Sr'AX' -8004.1223(.,1 PRODUCT INFORMATION SHEET 'rtFl:-HOND HANGER ADHESIVE ASrM E84-89a Surface Burning Characteristics APPI IFF) *10 INORGANIC IREINrORCED CEMENT- BOARD FL AMF S)PREAL) ... . ... ... ... ... ... SMOKE: DEVELOPED ... ... ... ... ... .. <5 Mil Pd 11FPA Class I or A SPECIAL CHARAGTERMUICS: 41 Non-Slip Fumiula * Immediate Grab 0 a Provides Excellent Watpr/Mildew Resistmice DESCRIPTION: Tuft-Bonft is a high-sirong1h, heavy-bodied, neoprene rubber adhesive, specifically formulated for,adhering anchors for hantling insulation. 'ruff-aoti(jift,Is also rocomm e ride d for use ns a general-purpose construction adhesive in applications high-.%!renqIh b(ind or in ziplilitalions subjected to high tPniper1Iijr(._f;. USES: Tuff-BondR bonds metal and nylon anchors to ryiptnl, concrete or fflqsorlry surfaces. Alsn recommended for Installing niei-11 or ceminic.wal! 1`10ires in file- SURFACE POr-HYARATIONS: StirtAres should be c1call, dry and free of oil, grease, frost or any other foreign matter that will Impair adhesion. Pairiled surfaces S1101110-he loullielle(l. epiall Illetcql SUtf(,lCes with 1,1,1 trichloloethfinp, acetone of other oxelclsiflp '.0, by (lip inantili0iner. Sonrin proloclive coatings are not compatible with IlM Solldfk Ilo.'rt-folo, llialq! o Incl hind br1oln plocpeding wi(h opplication. Slow adhesivo pit roomipi-riporniiii-o for of looct :M I 101ji': rrrol to use. APPLICATION: Dn not apply W temperatures hi low W-T- Prepare and instill one anchor at a time. Apply a(lob (file size of small wsl(ml.) of Tuff Rondill)to file rinchor base with a putty knife immediately (trisx. open time Is 10 minutes) pies aril-,hol fillWy in pincri, with S S1111tit 1wisting tyffAinn proppr adlisision, insure that the film of ndhosive c.ov(..!rinq llin nw.hor (aflcr tW, 'ifichot has hear; firmly pi-nc.51M into [)far.(,) Is protruding lilmligh flip perforated base [)late. Application �6411 he Illy""illi opployi-liM011 24./'1 Wom-,, dr,flPfidiliq on ;1firillsplieric. conditions DO rlof apply load linfil applicallf.111 is complelely d!Y NOTE- When inSl.'llIi0fj metal Of ceranile.wrill fixtures, buffer the back with Tuff-Bond®and immediately press in place wills n -y 24 objer t Mi(Ilit lwislhin motion. Allow to(it .72 lioiir�, br�fore ting 0 use CTIMAVIDD19(lot; Ut 006,^ VIMASCO 749 CORPORATION VAPOR-BLOKT" P a BOX 516'IT RU w%25141 ic ;.es '53.328 TOLL FREE (800) 624-8288 FAX (304) 755.7 153 VAPOR-BARRIER COATING 749 Vapor-BIokT" Mastic is a premium COLOR quality water-based vapor-barrier coating White, Gray which effectively prevents water vapor from WATER VAPOR P£RMEANCE(ASTM F 1249) passing through it. It is designed to pre- .03 to .05 U.S. Perms at 30 mils dry film vent the intrusion of water vapor into (.02 to .03 Metric Perms at.76 mm dry) thermal insulation when applied on sur- ,015 to .03 U.S. Perms at 38 mils dry film faces which are colder than ambient temperature. It is compatible with vir- (.01 to .02 Metric Perms at.97 mm dry) tually all types of thermal insulation and Each batch is tested for conformance can also be applied to a variety of other COVERAGE(ASTM C 46 1) types of substrates as needed. It is a safe, 30 sq ft/gal at 30 mils dry (52 mils wet) easy-to-apply water-based latex emulsion, (,74 m2/liter at .76 mm dry, 1.32 mm wet) but it achieves the type of low perm rating normally associated with solvent-based 24.5 sq ft/gal at 38 mils dry (66 mils wet) products. (.60 m2/liter at.97 mm dry, 1.68 mm wet) DRYING TIME(ASTM D 1640) 749 Vapor-BIokT" has a smooth, creamy To touch: 2 hours consistency most suitable for application Through: 12 to 48 hours by brush (it can also be sprayed with the Depending upon temperature, relative humidity,and substrate proper spray equipment). For applications WEIGHT PER U.S. GALLON(ASTM D 1475) where a heavy build is desired, a heavy- brush/trowel grade is available (method 10.4 pounds(1.24 kg/liter) of application should be specified when SOLIDS ordering).It has a pure white color which re- 67% by weight, 58% by volume mains white in service and matches most SERVICE TEMPERATURE RANGE white jacketings and facings. It is excel- 0°F to 180°F constant lent for protecting the insulation on cold (-17.8°C to 82.2°C) air ducts, chilled water lines, cold storage -20°F to 220°F intermittent equipment, and other similar cold sys tc...� (-290C t0 1040C) Note: ''Service temperature.' refers only to the temperature of air or 749 Vapor-BlokTM is a very low-odor, low surfaces coming into direct contact with the coating.This should not be VOC coating when compared to other confused with the operating temperature of the system underneath the coatings of this type, and thus it is pre- insulation,which may vary widely depending upon the effectiveness of the ferable to workers on the job site and also insulation used.749 Vapor-BIokT" will lose some flexibility at very cold when being applied in inhabited spaces. It temperatures and will soften at very warm temperatures. achieves its low perm rating at only 30 ,a PDL1CA-1 ION 7EMPERATURE RANGE mils dry film (30 sq ft/gal), therefore jobs 40°F to 120°F(40C to 490C) can be completed using less material than WE;FLAMMABILITY (ASTM D 93) with competitive products. No flash to boiling, 212°F(1001C) 749 Vapor-BIokT" is a very effective vapor VOLATILE ORGANIC COMPOUND (VOC;CONTENT (ASTM D 3960) barrier coating and should not be used .06 lb/gal (7.2 g/1) where a breathing coating is required. Al- ELONGATION ways make sure insulation being coated is 107% (30 mils dry @ 70°F) dry. (.76 mm dry @ 21°C) 749 Vapor-BIokT" meets the 25/50 flame CLEANUP and smoke requirements of NFPA 90A. Wet state:water Dry state:safety solvent 749 Vapor-BIokT" MUST BE PROTECTED RECOMMENDED SHELF LIFE FROM FREEZING IN SHIPMENT AND STOR- 12 months in unopened container at 40°F(4°C)to 90°F(32°C) AGE. After application it must be pro- CAUTION tected from freezing and moisture until thoroughly cured. The addition of water to this product will change its physical properties and will adversely affect its performance. No expressed or implied Note: 749 Vapor-BIokT" may be used out- warranty will be offered on applications where the product has been doors but after a considerable amount of thinned or altered in any way. exposure to ultra-violet light the white SURFACE BURNING CHARACTERISTICS version may dull slightly to an off-white. (ASTM E 84) It should not be applied to a flat hori- Flame Spread: 3.7 zontai.surface where it will be subjected to Smoke Developed:9.2 standing water. In accordance with OSHA Standard 29 CFR 1910.12 (Right to Know Law) a Material Safety Data Sheet is available for this product and all Vimasco products. ALL VIMASCO PRODUCTS ARE ASBESTOS FREE AND CONTAIN NO LEAD OR MERCURY COMPOUNDS. Vimasco products are designed to meet the needs of specific situations.They are warranted to be effective for their intended uses only.no further warranties are expressed or implied. The methods and condition of of lications over which we can exercise no control are important factors in the performance of our products.We make specitie rc commendations for the appiicatl n and use of all Vimasco products.but we cannot enforce our recommendations upon users:therefore.it is necessary that we state,as a condition of sale of ou products,that we will replace or refund the purchase price of any Vimasco products found by our laboratories to be detective. but that we assume no responsibi,tty beyond the purchase price of the materials. No representative of our Compam Distributor.or Agent has any authority to change or extend this condition of sale. 1-97/2`vt •rr> .. _ ti"' ,� w�r) �, 2"".' yi+ ics- ani^' t� n' NAUF INSULATION BOARDS r = a : 'SUBMITTAL; , zSHEET��- iWEV l T>Y Sir '7 � rl. t y _ .,. ! h'ice^ tAx Dumber: IG-SS 2" f �> � � s- Effective: July�li 1994} FIBER GLASS �. Supersedes IC SS 2, dated August , f992 .,.. •3•i�iLlil�i':ir'�ru" �f "4h � C'W `trt M t Aj Submittal Date: - � >r z zr - -nstto- x�-,yrgas•-'�+�^ XI Pi +y+f�Ta ty K Yl A 89. af''C"4�• T,�. k. i K}: ,. -} .x"' Description TEMPERATURE RANGE.(ASTM C 411)Knauf Insulation Board may be used at Knauf Insulation Board is a thermal and acoustical insulation product made from operating temperatures from-20'F to+450°F(-29°C to+232°C). inorganic glass fibers preformed into boards bonded by a thermosetting resin. WATER VAPOR TRANSMISSION RATE.(ASTM E 96,Procedure A)Both FSK The board is available plain,with a factory applied foil-skrim-kraft(FSK)or with a and ASJ vapor retarders have a maximum vapor transmission rate of.02 perms. factory-applied all service jacket(ASJ). BEACH PUNCTURE RESISTANCE.(ASTM D 781)The FSK facing has a beach puncture resistance of 25 units.The ASJ facing has a resistance of 50 units. Applications CORROSIVENESS.(ASTM C 665)Knauf Insulation Board will not cause corro- Knauf Insulation Board is a versatile product designed to be used ori heating sion of aluminum,steel or copper,and passes MIL-1-242448 for stress corrosion. and air conditioning ducts,power and process equipment,boiler and stack MOISTURE ADSORPTION.(ASTM C 553)Less than 5%moisture absorption installations,metal and masonry walls,wall and roof panel systems,curtain wall by weight when exposed to air at 120°F(49°C)and 95%relative humidity for assemblies,cavity walls and for all applications where insulating or acoustical 96 hours. efficiency is required. SHRINKAGE.(ASTM C 356)Knauf Insulation Board exhibits less than 0.3% Features and Benefits linear shrinkage. ENERGY CONSERVATION.Knauf Insulation Board has excellent thermal effi- ACOUSTICAL EFFICIENCY.Knauf Insulation Board,when tested in accordance oiency which results in lower operating costs. with ASTM C 423,E-795(Type A Mounting). OpIlk COST INSTALLATION.Knaut insulation Board is lightweight,easy to SOUND ABSORPTION COEFFICIENTS.Frequency Hz .iandle and fabricate resulting in quicker.lower cost field installation and lower Octave applied costs. 125 250 500 1000 2000 4000 NRC NOISE REDUCTION.Excellent acoustical properties effectively reduce sound 1.6 PCF Plain V.A." 19, 44 .86 98 102 10,,. ,_ .80_ transmission. i "6iffPCF PIew13`s?r ,y�_'.$1'.` `.gfc�` '.S' .. 1.9E 1.04 1.03 1.6 PCF Plan 2F' 43 .82 17 1 07 1 04 1 03 7;0 rvn 117 ,y„tA6 1.06 oa 104 105 ,k APPEARANCE.Both the FSK and ASJ vapor retardant facings provide a neat aYa:6 PCFPl�n3- ,', 2.25 PCF Plain 1', 05 24 9 86 97 100 c5 finished appearance. j zpgPIml1tE 1Z: '9 - 9a 7� ,- 103'>:e 1'� ; `a' - ° u 2.25 PCF Plain 2 26 62 C5 1.07 1.04 105 95 3g ZO PCE PIt ul f,,+. .62 °r w'M8!'is" 96 :; S"d`A89 r j .55" 3D PCF Plain 1'/+ 09 39 1 03 1 B9 Oo 1.01 85 Technical Data ;a•npCFpW1�� -mss �n1 113, 'x°6 "^T�"" '.0° 3.0 PCF Plain 3' 54 1.01 1,18 1.07 1.07 104 SURFACE BURNING CHARACTERISTICS.Knauf Insulation Board(UL i54.25PCFPph 6 1417 1. 107 x ¢1A6 1'10 4.25 PCF Plain 1" O6 24 69 99 1.05 1.02, 75 Classified)meets the requirements of NFPA 90A and NFPA 90B.When tested ,,,4APCFPhh AS', -r=a=:fi,.'. 77 ._'71 140M-304 =,M• -e0 in accordance with ASTM E 84,NFPA 255 and UL 723 and CAN 4-S102 as _4.0 PCF Plain 1'h 13 58 01 105 100 1.01 90 iaa4 ..0 PCF Pum 2-::,sw .,?,:: 1A9'"5�,.:.'1A& %1m � plain insulation or on a composite basis(insulation,facing and adhesive), 2.25 PCF FSK 1' 14 69 81 99 .55 27 5 Knauf Insulation Board does not exceed: � 5 3 0 PCF FSK 1"' 21 63 .84 93 51 22 ]5 25 Flame spread 3LMPCFFSK2" 67 .77 .- 74 ." 26 �0 50 Smoke developed 3.0 PCF FSK 2" 67 h 93 74 47 28 5 p .''&OPCFFSK"1'" a 2a-.�';. 5' ya".r'�"•`:at6 ..F4T'R.t.:��"'.�.,d2 Z:-7...50": 6.0 PCF FSK tYh" 61 47 78 61 51 35 60._ .�y,j',:O:OPCFfSI(2 "_° `r.7J.. t av50=-";;; '.72`;ua..'. �".,SBcr°Si"41:'.i. .41.�. J90;.: 3 0 PCF ASJ 1" 15 71 fi5 82 61 16 65 THERMAL EFFICIENCY.(ASTM C 177) 3.0PCF ASJ 2" 15 71 80 66 dt 2a 65 .55 6.0 PSF ASJ 1'6" 60 46 ,.62 d8 47 31 .50 _ .40 .057 U ilic,ASJ. ..2"x'.�s;ti',t.;,.�-77 :•'?'�"'�,;: _. _�:EO'.y.,"',v-"..".50,'-",�".'r'."`�;41:.:'� ,_,:90'.'_ 30 \2ro F, Specification Compliance Knauf Insulation Board complies to the property requirements of the following = specifications: c a .35 1 Fc) .050 HH-1.5588 Form A,Class 1 (1.6 PCF,2.25 PCF,3.0 PCF,4.25 PCF,6.0 PCF) (26 kg/m',36 kg;m',48 kg/m',68 kg/m3,96 kg/m') �� g0 F °? w� 0a3 E Form A,Class 2 (2.25 PCF,4.25 PCF,6.0 PCF),(36 kgim',68 kg/m',96 kg/m') 2`' QG 3 HH-B-1006 E 2 6� 0 V Type I(ASJ facing) Fm E Type II(FSK facing) 25 036 L ASTM C 1136 ~ Type I,II,Ill,IV(ASJ) Type 11,IV(FSK) ASTM C 612 .20 .029 Class 1 (1.6 PCI=,2.25 PCF,3.0 PCF,4.25 PCF,6.0 PCF) (26 kg/m',36 kg/m',48 kgfm',68 kg/m',96 kg/m') 0 50 100 150 200 250 300(:F) Class 2 (2.25 PCF,3.0 PCF,4.25 PCF,6.0 PCF) -18 10 38 66 93 121 149(C) (36 kg/m',48 kg/ml,68 kg/m',96 kg/m Mean Temp-ature JOB: ADDITIONS/ALTERATIONS ATLANTIC BEACH CITY HALL LOCATION: ATLANTIC BEACH, FLORIDA ENGINEER: ESTRELLA AND ASSOCIATES, INC. CONTRACTOR: CERTIFIED AIR CONTRACTORS, INC. SUPPLIER: SOUTHERN AIR SPECIALTIES, INC. DATE: OCTOBER 5, 2004 ITEM MANUFACTURER AND MODEL # 1 . Ceiling Supply Diffuser Tuttle/Bailey A1200-LT-TRM147 Tag: A Finish: White 2. Ceiling Supply Diffuser Tuttle/Bailey A1200-LT Tag: B Finish: White 3. Ceiling Return Air Grille Tuttle/Bailey APR-LT Tag: C Finish: White 4. Manual Volume Dampers Nailor 1870 Less than 10" high Aw 5. Manual Volume Dampers Nailor 1820 10" and higher 6. Louver NCA XAD-2-45-GL-F Finish: Clear Anodize 7. Backdraft Damper NCA XABD-2 8. Spin-in Fittings Jer-Air S-4 9. Flexible Duct Thermaflex G-KM R-6 s� Tuttle & Bailey, SUBMITTAL DRAWING •-Steyr Aluminum (Al 200) construction • Core is non-removable • 2-cone stepdown diffuser • Optional round damper to be ordered separately • Frame SF (surface mount) includes an aluminum and field mounted mounting frame • Damper is adjustable through hole in • Standard finish is white center cone • Two earthquake tabs are standard on all ` frame styles Face View E] FRAME SF - � � See specific frame details for dimensions (SEEirr EARNOTES) TAB (BEE A OTES)fEH) B 1-3118' �---13-114'--'�r- FRAME LT A J_ B 0 1-tla 1 ❑ FRAME PL �A J B 1-TT 11-31112 -� are- NOMINAL SERIES 1200 SERIES S1200 SERIES A1200 DROP 7/16 NECK STEEL& STEEL ALUMINUM SIZE ALUMINUM A B B A-y 6 5 7/8" 1 1/2" 1 1/2" [J FRAME NR I e 8 T W 1 1/2" 1 1/2" tyle. 5116' 11-11ri2 DROP 3116 Dimensions are in inches, Product information subject to change without notice PROJECT: TLA /C &4CY cog „SUBMITTED BY: DDATE: 9-1=00 SD-1762 ARCHITECT: 51200 & A1200 Series ENGINEER: Fixed Pattern Diffuser - CONTRACTOR: 2-Cone w/Round Neck LOCATION: 12 X 12 module VIL Tuttle & Bailey, SUBMITTAL DRAWING • £tcet-f3t2OWorAluminum (A1200A) • Two earthquake tabs are standard on all construction frame styles • 2-cone stepdown diffuser • Core is non-removable • Frame SF (surface mount) includes an • Optional round damper to be ordered separately aluminum mounting frame and field mounted • Adjustable pattern controllers on the cores • Damper is adjustable through hole in • Standard finish is white center cone Face View CEILING OPENING See specific frame details for dimensions FRAME SF 24.112- —� EARTHQUAKE TAB A (SEE NOTES) B 3 7/16' 251/4" FRAME LT A--� I B 3 3M' - 23 3/4" FRAME PL [-A-�r 1 B 3 3/B" NOMINAL SERIES 1200 SERIES S1200 SERIES A1200 3/8' 23 31W NECK STEEL& STEEL ALUMINUM DROP 7/16' SIZE ALUMINUM FRAME NR 1 6 5 7/8" 1" 1 1/2" B 8 7 7/8" 1" 1 1/2" 31 10 9 7/8" 1 1/2" 1 1/2" 12 11 7/8" 1 1/2" 1 1/2" 511 2313!32' DROP 1 14 13 7/8" 1 1/2" 1 1/2" P 3/1x- 15 14 7/8" 1 1/2" 1 1/2" Dimensions are in inches, Product information subject to change without notice PROJECT: T T/ , -j4 UBMITTED BY: DATE: 9-1-00 SD-1765 ARCHITECT: S1 200A & Al 200A Series ENGINEER: Adjustable Pattern Diffuser - CONTRACTOR: 2-Cone w/Round Neck LOCATION: 24 X 24 module 4A"LBailey,Tuttle & SUBMITTAL DRAWING • Matching return for PV, PP, and PM supply diffusers • Hinged / removable face allows for easy access to damper • Optional square damper is shipped loose and field mounted c tion • Model APR is steel backpan with aluminum face • Standard finish is white 23" TYPICAL OF A L FRAME STYLES 1/4"] 25" SEE FRAME DETAIL FOR F] Frame SF(Surface Mount) _ TYPICAL OVERALL *minimum ceiling opening 23-1/4" DIMENSIONS 23-3/4" 23" Frame LT(Lay-in-T-Bar) 23-3/4" PR APR INTEGRAL SPLINE 2 SIDES OPTIONAL 23-15/16" DUCT SIZE DAMPER EARTHQUAKE TAB r LESS 1/8" Frame PL(Spline) 2 PLACE 23-3/4" 3 3/8" 23" L Side View/Damper Detail, SF Frame F] Frame TG—(Tegular) 1/4" **NOTE: Frame TG not DIA.HOLE3/16S SS 3/ 118" available for Model APR Frame Detail: 7/f6-7/32" 24 x 24 Module Size SPRING RETAINER Perforated Pattern Detail (51%free area) Face Hinge Detail ��t' Dimensions are in inches. Product information subject to change without notice. PROJECT*A—,6 r .�R/uT/<_" q({l/C.rT SUBMITTED BY: DATE: 7/02/01 SD - 1779 ARCHITECT. PR, APR Square Neck ENGINEER: Perforated Return CONTRACTOR: 24 X 24 Module Size LOCATION: ailor MANUAL BALANCING DAMPER Industries Inc. MODEL: 1870 SINGLE BLADE The Model 1870 Manual Balancing Damper is an economical branch duct balancing damper designed for use in most metal and fibre ductboard HVAC systems. The low profile frame and sills allow maximum free area. The ribbed forms in the blade and frame are for extra strength. WtpTH=NOMtNAI MINUS V4 l6� o STANDARD CONSTRUCTION: Frame: 3"wide x 18 ga. (102 x 1.3)galvanized Q ° steel. Z Blade: 20 ga. (1.0) galvanized steel up to 24"x 12"(610 x 305). 18.9a. (1.3) galvanized steel above 24"x 12"(610 x 305). o Shaft: 1/4"(6)square plated steel. ? Quadrant: Plated steel with locking operator (shipped loose). _ ° Minimum Size: 4"x 4" (102 x 102). All units are manufactured 1/4" (6) (z� under nominal size. Maximum Size: 36"x 12" (914 x 305). All units are manufactured 1/4" (6) under nominal size. Temperature Range: -50*F to approximately 180°F (-45°C to 82°C). ZZY ---------------- \ For larger units; refer to Models 1810 and 1820. Cl 1 IG ACCESSORIES: 2" (51) stand-off bracket for hand quadrant (for externally insulated duct). PERFORMANCE: LOCKING QUADRANT Maximum System Pressure: 2"w.g. (0.49 Kpa). Maximum Face Velocity: 1500 fpm(7.6 m/s). d PROJECT 71 /;�J r'-(. n ENGINEER Dimensions are in inches(mm). DATE B SERIES SUPERSEDES DRAWING N0. CONTRACTOR 10-5-99 1800 6.97 1800-2 Nailor Industries Inc.reserves the right to change any information concerning product or pricing without notice. MANUAL BALANCING DAMPER Illllllliji Nailor MODELS: 1810 PARALLEL BLADE Industries Inc. 1820 OPPOSED BLADE The Nailor 1800 Series Dampers are especially designed for manual balancing applications. They are suitable for use in the majority of • ' commercial low to medium pressure and velocity HVAC systems. They are designed and built to provide a cost effective and reliable damper for reduced volume control and not positive shut-off.They are not recommended for applications as an automatic control damper. e The 1800 Series includes many of the design features incorporated in the - m Nailor 1000 Series Control Dampers.These include a sturdy hat channel ti frame with die4ormed comer gussets for reinforcement, a roll-formed N triple-vee blade design that maximizes strength and zero maintenance �3 concealed linkage(out of the air stream)for reduced air turbulence. Nailor's 1800 Series exceed the volume damper design recommendations in SMACNA'HVAC Duct Construction Standards - ccW Metal and Flexible' 06t edition 1985), and offer an economical To manufactured product alternative to custom'shop built'dampers. m OPE►+ STANDARD CONSTRUCTION: L Frame: 5' x 7/8" x 16 ga. (127 x 22 x 1.6) galvanized steel hat channel with die-formed comer gussets. Low profile (flat top and bottom) on dampers 10' (254) 114-p high and under. Blades: 6" (152) wide on 5 1/2" (140) centers. 16 ga. (1.6) MODEL galvanized steel triple-vee designParallel or MODEL . 1810 1820 opposed action. PARALLEL OPPOSED Linkage: Concealed type totally enclosed within the frame BLADE BLADE and out of the airstream. Plated steel. (optional) (standard) Bearings: 1/2' (13)dia.celconO. Axles: 1/2" (13)dia. plated steel double bolted to blades. Drive Shaft: 6" (152) long x 1/2" (13) dia. double-bolted fixed drive shaft on each damper section. The drive shaft is easily removed if required. Minimum Size: Single blade(parallel): 6"x 4' (152 x 102). (° 19j aM(22 Two blades(parallel or opposed):6"x 10"(152 x 254). Maximum Size: Single section size is 48"x 72' (1219 x 1829). (OTO The low Multiple section assembly:96"x 144'(2438 x 3658). profile frameillustrated is Temperature Range:-50'F to 250OF(-45'C to 121'C) usedto OPTIONS: maramize free area on units ❑ BO Oilite bearings 10'(254)high ❑ 304 Stainless Steel Contraction and under. ❑ DLO Lode-on drive shaft ❑ HLQ Hand-locking quadrant(one required per damper section) OPTIONAL '63 H02 Hand-locking quadrant with 2" (51)stand-off bracket LOCK-0N o 0 C1Other DRIVE SHAFT PERFORMANCE: Dampers are designed to operate in a clean,dry environment.For proper operation,dampers must be installed without racking.The OPTIONAL � �. hand quadrant must be installed on the indicated drive blade. HAND-LOCKING Maximum System Pressure: 2.5'w.g. (625 pa). QUADRANT Maximum Face Velocity: 2000 fpm(10 m/s). 7/8"(22)stand-off ° 0 PROJECT /q7/,4/,f7/ Dimensions are in inches(mm). ENGINEER DATE L1800 SERIES SUPERSEDES DRAWING NO. CONTRACTOR 10-5-99 5-97 1800-1 Nailor Industries Inc.reserves the right to change arty information concerning product or pricing without notice. amca CERTIFIED MODEL Xi4D-2-45-GL RRTIIIG! UIRTER EXTRUDED STATIONARY LOUVER D pW DRAINABLE BLADE. AMCA LICENSED. 2' Standard Construction: (50.8mm) Frame: 2"x .063 (50.8 mm x 1.6 mm)extruded aluminum (6063-T5). Blades: .063(1.6 mm)extruded aluminum (6063-T5), approximately 2-1/4"(57 mm)on centers. Blade Angle: 45° Screen: Bird screen-3/4"x.050(19 mm x 12.7 mm) flattened expanded aluminum in a removable frame on interior of louver. Finish: Mill aluminum. Minimum Size: 6"w x 6"h (152 mm x 152 mm) Options: Screens: Insect screen- 18 x 16 mesh aluminum 1/2"x.063(12.7 mm x 1.6 mm)aluminum Other- Finish: Prime Coat Baked Enamel .+►Clear Anodize-204-R1 and 215-R1 Integral Color Anodize Kynar 500 Enamel T— Other- Sill Extensions: 2-1/4" Flange: 1-1/2" (38 mm)(front or rear) (57 mm) Notes: Louvers fabricated 1/4"(6.4 mm)under opening size unless otherwise noted. Channel Frame rn 0 J u) N r- - - - - - - - - - —s-- - - - - - - - ---- 0 a X 11c 11 1-1/2"(34mm Jamb Visible Mullion Sill Extension I Flange Frame Specifications are correct at time of printing.However,as part of our'continuous improvement program,'we reserve the right to make further improvements without notice. ©2002 NCA Manufacturing Project: 4;Z 4A -71C: 412-7!4C* L/'7/7- 141-4/„U Contractor: Location: Address: Architect: P.O. Number: Engineer: Date: NCA MANUFACTURING, INC. 0 DALLAS,TEXAS NCA MANUFACTURING, LIMITED 0 TORONTO,CANADA MODEL Xif1D-2-45-GL LOUVER PERFORMANCE DATA DRAINABLE BLADE. AMCA LICENSED. 000, k ©2002 NCA Manufacturing Specifications Furnish and install where shown model XAD-2-45-GL louver, manufactured by NCA Manufacturing. Louvers shall be the stationary drainable type with a frame depth of 2 inches. Frames and blades shall be .063 inches thick 6063-T5 extruded aluminum alloy. Blades shall be located on a 45 degree blade angle. Screens shall consist of 3/4" expanded aluminum,with an extruded frame, mounted to the louver interior, and be removable for cleaning. Louvers shall be finished with Polyurethane Acrylic enamel, Kynar 500,Anodize or other finishes selected by the architect from NCA standard color charts. XAD-2-45-GL Free Area in Sq. Ft. Width-Inches 6 12 18 24 30 1 36 42 48 54 60 66 72 78 1 84 1 90 96 6 0.06 0.14 1 0.22 1 0.31 0.39 0.47 0.56 0.64 0.72 0.81 0.89 0.97 1.06 1.14 1.22 1.31 12 0.13 0.31 0.50 1 0.69 0.88 1.06 1.25 1.44 1.63 1.81 2.00 2.19 2.38 2.56 2.75 2.94 18 0.23 0.56 0.90 1.24 1.58 1.91 2.25 2.59 2.93 3.26 3.60 3.94 4.28 4.61 4.95 5.29 24 0.29 0.74 1.18 1.62 2.06 2.50 2.95 3.39 3.83 4.27 4.71 5.16 5.60 6.04 6.48 6.92 30 0.40 0.99 1.59 2.18 2.78 3.37 3.97 4.56 5.15 5.75 6.34 6.94 7.53 8.13 8.72 9.32 36 0.47 1.16 1.86 2.56 3.26 3.96 4.66 5.36 6.06 6.75 7.45 8.15 8.85 9.55 10.25 10.95 ayi 42 0.54 1.34 2.14 2.94 3.75 4.55 5.35 6.16 1 6.96 7.76 8.57 9.37 10.17 10.98 11.78 12.58 48 0.64 1 1.59 2.55 3.50 4.46 5.42 6.37 7.33 8.28 9.24 10.19 11.15 12.10 13.06 14.02 14.97 54 0.71 1.77 1 2.83 3.89 4.95 6.01 7.07 8.13 9.19 10.25 11.31 12.37 13.43 14.49 15.55 16.61 t 60 0.78 1.95 3.13 4.30 5.47 6.64 7.81 8.98 10.16 11.33 12.50 1 13.671 14.84 16.02 17.19 18.36 m 66 0.88 2.19 3.51 4.83 6.15 7.46 8.78 10.10 11.41 12.73 14.05 1 15.361 16.68 18.00 19.31 120.63 = 72 0.95 2.37 3.79 5.21 6.63 8.05 9.48 10.90 12.32 13.74 15.16 16.581 18.00 19.42 20.85 22.27 ff84 1.05 2.62 4.20 5.77 7.35 8.92 10.49 12.07 13.64 15.22 16.79 18.37 19.94 21.51 23.09 24.66 1.12 2.804.48 6.15 7.83 9.51 11.19 12.87 14.54 16.22 17.90 19.58 21.26 22.93 24.61 26.29 1.19 2.97 4.75 6.53 8.31 10.09 11.88 13.66 15.44 17.22 19.00 20.78 22.56 24.34 26.13 27.91 1.29 3.23 5.16 7.10 9.03 10.97 12.90 14.84 116.78 1 18.71 20.65 22.58 24.52 26.45 28.39 30.32 1 .30 9 a W e Cc a 27 3 X s w 5 y ¢ 24 4 LL 2 U- W W 3 0 .21 3 U 2.5 W O Z 2 o „°,¢ .18 N 5 Q W Ul _ W 15 U N F 8 O i z i .12 IL p 5 O cc o x 5 Q .09 W - 4 W 7 (n cc 3 W .06 rn W 2.5 d U 2 w .03 IL Z- ,s ~ � .01 1 1.5 2 2.5 3 4 5 6 7 8 910 1.5 2 2.5 3 4 5 6 7 8 910 600 700 800 900 SCALE X 100 SCALE X 1000 FREE AREA VELOCITY V(fpm) VELOCITY THROUGH FREE AREA FPM X 100 Water Penetration 000W PRESSURE DROP INTAKE Water Penetration Data applies to test unit size 48"x 48"only. amccl Beginning of Water Penetration is 734 FPM Free Area Velocity. CEIMFrEo nnrreci Performance shown is at standard air density 0.075 lbs./ft3. D WATER ij NCA Manufacturing,Inc.certifies that the Model XAD-2-45-GL louver shown herein is licensed to bear the AMCA seal.The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified Ratings program. The AMCA Certified Seal applies to air performance ratings and water penetration ratings. November 2002 NCA MANUFACTURING, INC. 0 DALLAS,TEXAS NCA MANUFACTURING, LIMITED 0 TORONTO, CANADA 06 MODEL XABD-2 EXTRUDED ALUMINUM BACKDRAFT DAMPER Standard Construction: Frame: .070(1.8 mm) extruded aluminum. Blades: .052(1.3 mm)extruded aluminum. Bearings: Nylon. Axles: 3/16" (4.8 mm) dia. nylon. Seals: Vinyl blade seals. Linkage: Heavy gauge aluminum brackets with aluminum linkage bar. Finish: Mill aluminum. Minimum Damper Size: Single Blade-6"w x 6"h (152 mm x 152 mm) Maximum Damper Size: Single Section-40"w x 52"h (1015 mm x 1321 mm) Maximum Velocity: 2500 fpm ' Options: Counterweight: Assist or Retard Flange: 1-1/4"(32 mm) Flange frame (front or rear) _. 2-1/2" Operators: Electric motor operators (63.5 mm) Mounting: Horizontal mount(up blast only) r Finish: Speical finishes Notes: ° •All dampers are fabricated 1/4"under listed size 11 unless specified"actual or exact". •Dampers must be installed square and free from racking. co o o 17- C14 a O Q o 0 0 0 --Air Flow X Air Flow -J -� 3/4 (19 MM) 1-1/4" (32 Mj 1 5-3/8° 1 Flange A Flange B (136.5 mm) Specifications are correct at time of printing.However,as part of our'continuous improvement program,'we reserve the right to make further improvements without notice. ©2003 NCA Manufacturing Project: Contractor: Location: Address: Architect: P.O. Number: Engineer: Date: NCA MANUFACTURING, INC. 0 DALLAS,TEXAS NCA MANUFACTURING, LIMITED N TORONTO,CANADA / * - • NCA . , . • • • - • • - •. .- ■■■■■■■■■�I■MEMO■■tIII . .- . �. ..- . -• - ■■■■■■■ 111■III■■■milli -. .. .- -. - •. . . -. ■■■■■■11111■■■I■■■1111 . •- • - - • ••• - � : ■ • -• ■■■�■■��III■■■�■■ 1111 ' • '" '• '' ■■■■MOM II■■■■■■11111 - .-. . - . . . 11 . ■■■■■■■""■111■■■IN Eon ��...........�=mom..Mall .. ■..■■■.■■■■ ■i■■.■■■.■� • . . . . E■M■■M■■11��1■r�■■■■■■1111 ' ■■■■■■■�III��■■■■■1111 Blade - ■■■■■■■IIIA■■■■■11111 ■M■■O■M11r:4 Ell ■■111/1 Position ■■■■■■/ilil■0■■■■■1111 ' • • •-311 1 1 - ■��/�11111■■■1■■11111 1'. OpenMOW 1 :11 75% pen M1111FANTIN M. Man ■■.■■■••1�.■■.■■■•■1 ■■■■Ems Sol■111■■lmm■1110■111111 11111111 on 11MIM 0 ■■11■111111■/11■111111 m�� , �®�� . :. ------.....------IN HIM MEMO. a m mmmmmm MEME IS mom an 010 OIEon■■11■III=■■■■■11■111 ■■■t■■ 1111■■■t■■ 1111 m •• ®� • OI■■11■■■I,'/ll■1■■11■■111111 ®�� •• • • • ■■■1■■I%111■■ ■t■■�IIII 0 �' �� . .. .: ■■11■/11111■■11■111111 m®�� . , ® ; . . : , , mss. Spin-In Take Offs For use with galvanized truck duct S-1 S-2 S-3 S-4 I/ Standard Features: 2 Sz CkVT • 45' Scoop • Sizes 4" thru 12" constructed with 28 gage galvanized steelc/ • Sizes 14" thru 20" constructed with 26 gage galvanized steel • Factory assembled adjustable damper hardware • Barrel exit beaded WA. • Riveted construction • Barrel length 4" thru 7" - 6" long 8" thru 10" - 8" long 12" thru 20" - 12" long Also Available Upon Request • 90' scoop • 26 gage construction ORDER A B C CUT SIZE HOLE B -7 C 4 3-7/8 5-518 2-112 3-7/8 5 4-718 5-518 3 4-718 6 5-718 5-518 3-1/2 5-7/8 7 6-718 5-5/8 4 6-718 A 8 7-7/8 9-5/8 4-112 7-7/8 9 8-7/8 9-5/8 5 8-7/8 10 9-718 9-5/8 5-1/2 9-7/8 12 11.7/8 11-5/8 6-1/2 11-7/8 14 13-7/8 11-5/8 7-1/2 13-7/8 16 15-7/8 11-518 8-112 15-718 18 17-7/8 11.5/8 9-1/2 17-7/8 20 19-7/8 11-518 10 112 19 718 3 11 GnKM Rm6 rnepms owINSULATED FLEXIBLE AIR DUCT FOR ® LOW AND MEDIUM PRESSURE SYSTEMS Applications and Engineering Data 4 5 6 7 _8 9 10 12 14 16 N Wit 25 25 25 25 25 25 25 25 25 25 > SNS OlBANQiA IUS iric�l'®' 4 5 6 7 8 9 10 12 14 16 PRA 11J ' Sll �I�i�Che at�r'�i�a tit�il*� 1 1 - 1 _ 1 1 1 1 1 0_5 0.5 .` _ —20 250 AIM PASS"BY U`id M p.ubwmn B —-- - _ =adc M AGCOBONN:E WaN AOC FLEXIBLE DICT — — PERFOFYIANQE AND 94G1 ATION STANDMTDS 6.0 �' `V (1191)USING ASTM 0311 IM/11 AT WTAIM WAU' 4e � THCK M ON RAT MSUAT m ply — — -—._.——_ ------- ow R-6.2 Ke nemw Fen. 5" � ® --- ---- _165 MRftp 0` Isa — — .27 If 25 - A qEUIPDa. .,; 50 qR 11 � 'Sttlt� . , Nf3: . -T 0.1 -- R��.. 31.30 23.32 ----------- NOTE:For detailed information concerning air friction loss and acoustical data,refer to separate technical bulletins published by Flexible Technologies,Inc.Tests performed according 4*4 to Air Diffusion Council Flexible Air Test Code FD72R1. lack r Pp, olyethylene - lm vapor- Construction barrier nd Materials Fiber glass insulation - CPE duct inner liner is permanently CPE liner-------- --- --- bonded to a coated spring steel n wire helix, also supporting fiber coated spring ---- -- - steel wire helix glass scrim and a blanket of fiber glass insulation. Vapor barrier is an Fiber glass__.__..__-_____-..____._- _ '..,:outer,-'ac e1,ool elf gene. scrim Suggested Specification Flexible air duct for connections between and shall be Thermaflex° G-KM R-6 air duct Listed by Underwriters Laboratories under UL Standard 181 as Class 1 flexible air duct and complying with NFPA Standards 90A and 90B.Duct shall be factory made and composed of:a CPE liner duct permanently bonded to a coated spring steel wire helix supporting a thick fiber glass insulating blanket with fiber glass scrim.Low permeability outer vapor barrier shall complete the assembly. Offices ies warrants that all Thermaflex in NATIONAL SALES HEADQUARTERS 'LA MIRADA,CA 90638 WARRANTY.Flexible Technologies ABBEVILLE,SC 29620 14657 Industry Circle sulated and non-insulated products will be free from defects in Box 888(Carwellyn Rd.) Phone 714 523-1804 materials and factory workmanship for a period of five years from Phone 803 459-5441 the date of manufacture.This warranty applies only to ducts proper- 'CANADA ly installed in accordance to Flexible Technologies written installa- CUSTOMER SERVICES DEPARTMENT 1630 Matheson Blvd.E. tion instructions and under conditions specified in published per- ABBEVILLE,SC 29620 Unit C Box BBB(Carwellyn Rd.) Mississauga,Ontario L4W1Y4 formance data. Flexible Technologies shall not be liable to buyer Phone 803 459-5441 Phone 905 602-9660 or any third party for any special,secondary,incidental or conse- quential damages however arising. 'For order entry,expediting and product information,contact we're Flexible• the Abbeville,SC,La Mirada,CA DISTRIBUTED BY: or Mississauga,Ontario FLEXIBLE TECHNOLOGIES, INC. Customer Services Department. A SUBSIDIARY OF SMITHS INDUSTRIES 0 Bulletin G-KM R-6 3/95 25C Printed in USA(P&B) �o� TABLE 1-5 RECTANGULAR DUCT REINFORCEMENT W.G. REINFORCEMENT CODE FOR DUCT GAGE NO. STATIC NO POS.OR NEG. REINFORCE- REINFORCEMENT SPACING OPTIONS MENT DUCT REQUIRED DIMENSION 10' 8' 6' S' 4' 3' 2112' 2' O O O O O O O O 10 10"dn 26 ga. NOT REQUIRED 11, 12" 24 ga. B-26 B-26 B-26 B-26 B-26 B-26 B-26 13, 14" 22 ga. B-2a B-26 B-26 B-26 8-26 B-26 B-26 15, 16" 20 ga. C-22 C-24 C-24 C-26 C-26 C-26 B-26 B-26 17, 18" 20 ga. C-22 C-24 C-24 C-26 C-26 C-26 C-26 B-26 19, 20" 18 ga. C-20 C-22 C-24 C-26 C-26 C-26 C-26 C-26 21, 22" 16 ga. D-20 D-22 D-24 D-26 C-26 C-26 C-26 C-26 23, 24" 16 ga. E-20 E-22 D-24 D-26 D-26 C-26 C-26 C-26 25, 26" E-20 E-22 E-24 D-26 D-26 C-26 C-26 C-26 27, 28" F-18 E-20 E-22 E-24 D-26 D-26 C-26 C-26 29, 30" F-18 F-20 E-22 E-24 E-26 D-26 D-26 C-26 31-36" G-16 G-18 F-20 F-22 E-24 E-26 D-26 D-26 37-42" H-16 G-18 G-20 F-24 E-24 E-26 E-26 43-48" 1-16 H-18 H-20 G-22 F-24 F-24 E-24 49-54" 1-16G H-1 BG H-20G G-24 F-24 F-24 55-60" 1-16G 1-18G H-18G G-22 G-24 F-24 61-72 NOT J-16H 1-18G H-22G H-22G H-24 73-84" DESIGNED 1-18G 1-20G 1-22G 1-22G 85-96" J-1 8H 1-18H 1-20H 1-22H 97-108" K-18H J-18H 1-18H 109-120" K-181 J-181 See page 1-15. Circles in the Table denotes only column numbers. For column 2, see Fig. 1-7. For columns 3 through 9, see itroduction to Schedules. The number in the box is minimum duct gage;the alphabet letter is the minimum reinforcement grade for joints and intermediates occurring at a maximum spacing interval in the column heading. A letter to the right of the gage gives a tie rodded reinforcement alternative. A'T'compels use of tie rod(s)for the reinforcement listing. For beading or crossbreaking, see Fig. 1-8. 1.22 HVAC Duct Construction Standards Metal and Flexible- Second Edition � WACN READING GUIDE SUMMARY Example: 54"x 18"duct,5 ft joint spacing- On 54"sides use F joints on 22 ga. On 18"sides flat slips or drives qualify per Joint Option: Backup Column 2. member qualifies Hemmed Example: 54"x 30"duct,22 gage. Use F at 5 ft.on 54". On "S11 Slip-Reinforced or 30"use D at 5 ft.or E at 10 ft. If you put joints on the 30"side Drive Slip-Reinforced for Use Drive Slip or Hemmed at 5 ft. spacing,they must be D rated. letter code when selected "S"Slip on duct gage in from Table 1-10. column 2 Comment: If the table requires a letter code,all joints on that side must qualify for the minimum code letter related to the 3'MAX minimum gage and the spacing. HEMMED-S-SLIP DRIVE SLIP OR DuctGage 26 t0 22 20 78 16 OR �E Minimum Flat Slip and Drive Gage 24 22 20 18 3-MAX Will Spacing refers to letter code: use joint-to-joint, joint-to intermediate or intermediate-to-intermediate. Columns 3to10 are alternatives. DRIVE SUP-REINFORCED HEMMED"S"SLIP The drive slip is accepted as being A, B or C rated up to 20" length. TABLE 1-11 TABLE 1-10 (Option) (Option) TABLE 1-4 TRANSVERSE JOINT INTERMEDIATE RECTANGULAR DUCT REINFORCEMENT _. F T W.G. REINFORCEMENT CODE FOR DUCT GAGE NO. T- sTATIC NO H POSTATIC NEG. REINFORCE- REINFORCEMENT SPACING OPTIONS HENT _ M 1 DUCT REQUIRED 1. REINF :r "--4 DIMENSION 10 e• e• 6• a• r nrr z CLASS ANGLE O O O O O O O O O 7D RIN 111111.111,1111 GIDITY T•1D Er wr CLASS STANDINGS H.TrNNI LF 10"dn 26 ga. NOT REQUIRED Er IBR A 05 L!C 17,12" 26 ga. H.T LF a 10 u..0 13,14" 24 ga. 8-26 0-28 B-28 &28 6-26 M26 A-2B A-M A 0.5 u.e e a 10 1.280. 06 C LD CL 160• Dao 15,16" 22 ga. &za fiae 8-28 6.29 8-2e 0-16 8-26 M2B C3..IA D.SD 17,18" 22 ga. S-24 Bae 0-26 8-26 &26 8-26 8-20 B-2B C iD 1.220. 08 F11..to 057 D 17 C1.141 0.80 19.20" 20 ga. G28 C-26 C-26 C-26 &28 B-26 &26 D 27 1.1A.20 09 C1 I1a.12 9. O D a Y E o5 N1.to 00 21,22" 18 ga. C-2.\ C-24 C-26 C-26 C-26 8-26 B-26 B-26 E 651.0 F Ile H11M.tA 102 23.24" 18 ga. C-24G2a G26 C-26 c-2e c•26 6-26 B-26 in.1A la 25.26" 18 ga. 0.22 2+ C-26 C-26 C-26 c-26 C-26 B-26 Ile ur c O R G 1s e 1sB tve.le 1] 27,26" 16 ga. D21 o-2 0.26 G28 GZB C-28 c-26 GG 26 w 22(•) 11R z3n6 17e N 267 2.1A las 29.30" 16 ga. E-22 24 0.26 D-26 C-26 Cab C-26 N 22 0 C2.1,e 2w 31-36" E-20 E-2 a4 0.24 0.28 C-2e C-26 1 eD I 21x2.14 21 37-42" F-IB F-20 E-2a E-28 D.- G26 /4..vie J 80 J m C2.lu 12 r2A(•1 43-46" G18 G18 F-1 21 .1 2, F-22 E-2b E•2B D-26 49-54" K16 H-18 G-20 F-22 F-24 E•2+ E-24 E-N K ,03 K 100 21RxJ/16 ]1 a1 55.60" H-18 G-20 Ga F-24 f-14 E-24 E-24L 207 L 207 H2112.1. 61-72" NOT H-18G H-19G -22G F-2a F.24 F-21 73-84" DESIGNED 1-leG 1-'- 120G It-22G H-z2G G-u C angle is cold rolled. 8596" 1.leH 1-1eN 1-2oG r«zoc H-uc H angle is hot rolled. 97-106" 1-16G I.18G I.iaG 1-,BG 109.120" 1-18H -1BM 1-18G See page 1-15. Circles In the Table denotes only column numbers. For column 2,see Fig.1-7. For Columns 3 through 9,see introduction to schedules. The number in the box Is minimum duct gage;the alphabet letter is the minimum reinforcement grade for joints and intermediates occurring at a maximum sp;cmg interval in the column heading. A listing such as H 18G means that the H may be downsized to G with a he rod. At higher pressures and large widths•a reinforcement such as Jt means that only he rodded members are given. 1.14 HVAC Duct Construction Standards Metal and Flexible- Second EditionCNA TABLE 1-11 TRANSVERSE JOINT REINFORCEMENT H Hq i H H I H H T-13 jc_: i � LHT-2 REINF. STANDING T-10T-11 T-12 T-14 CLASS DRIVE SLIP STANDIN S STANDING S TANDING S STANDING S Er WT vVf wT WT WT HxT LF H x T LF H x T LF H x T LF HxTxHR LF A 0.43 Use B Use B 12 x 26 ga. 0.5 Use B Use D B 1.0 1 1/8 x 26 ga. 0.4 1 x 26 ga. 0.6 1/2x 22 ga. 0.6 1 x 26 ga. 0.7 1 x 26 ga. Use D 1 1/8 x 22 ga. 0.6 1 x 22 ga. 0.8 1 x 22 ga. 0.8 1 x 24 ga. 0.8 � 1.9 Use D 1 1/8 x 18 ga. 0.8 1 1/8 x 20 ga. 0.9 1 x 20 ga. 0.9 1 1/2 x 22 ga. 1.0 1 5/8 x 24 ga. 1.4 D 2.7 1 x 22 ga.(+) 1 x 22 ga.(+) 1 12 x 1/8 Bar 11/8x18ga. 1.0 1x18aa (+) 1.0 1x18ga. 1.2 E 6.5 1 12 x 20 ga. Use F 1 5/8 x 22 ga F 12.8 Use G Use G 1 12 x 1/8 Bar 1.5 1 5/8 x 18 ga. 1.3 1 12 x 18 ga. 1.3 1 5/8 x 20 ga. 1.7 G 15.8 1 12 x 1/8 Bar 22(+) 1 5/8 x 18 ga. H 264(-) 1 12 x 1/8 Bar 2.0 NOT GIVEN 2 1/8 x 20 ga. 1 69 NOT GIVEN 2 x 2 x 1/8 2.9 Angle 2 1/8 x 20 ga. J 80 NOT GIVEN NOT GIVEN 2 x 2 x 3/16 3.7 Angle K 103 NOT GIVEN L 207 Set page 1-15. 'Effective EI is number listed times 105 before adjustment for bending moment capacity. Plus(-)or minus(-)is a pressure mode restriction. Both modes are accepted when neither is given. Joints T-'_and T-10 through T-14 are restricted to 30"length at 4"w.g.,to 36"length at 3" W.If and are not recommended for service above 4"w,g. 1.34 HVAC Duct Construction Standards Metal and Flexible- Second Edition FSMaCIIQ USE MAXIMUM LENGTH OF f CONNECTORS NOTCH CORRECTLY JTS T-10 TO T-14 "S"-SLIP OR T-2 T-5 OR T-6 CORNER HAMMERED OVER 1 DRIVE SLIP DRIVE T-1 OR T-2 SLIP T-1 y r T FIGURE A OPEN HEM FOR DRIVE SLIP WHEN USING FLAT OR STANDINGS SLIPS ON ALL FOUR SIDES SEAL CORNERS_ BUTT OF STANDING S TYPE CONNECTORS FIGURE 8 FASTEN AT INTERVALS / SPECIFIED FOR THE PRESSURE CLASS - (16 mm) 5/8" 1"MIN. 1"MIN. (25 mm) (25 mm) I I MIN. DOUBLE S T-8 FIGURE C CORNER CLOSURES - SLIPS AND DRIVES FIG. 1-13 4M i HVAC Duct Construction Standards Metal and Flexible- Second Edition 1.79 n I I T-4,9, 17. 18, 19,20,AND 23,OMITTED H DUE TO INFREQUENT USE, MAY STILL BE `--J USED PER THE FIRST HE SPECIFYING AUTHORITY.DITION IF ACCEPTABLE TO T T-1 -DRIVE SLIP STANDING DRIVE SLIP T-3-REINFORCED T-2 16 GA. (76 mm) (1.61 mm) MAX. —� 3" ID�— ti' (25 mm) PLAIN"S"SLIP T-6 HEMMED"S"SLIP REINFORCED"S"SLIP T-8 DOUBLE"S"SLIP T-5 (T 6a REINFORCED) T-7 (T-8a REINFORCED) I I T T H II H H a �l STANDING S STANDING S(ALT.) STANDING S(ALT.) STANDING S T-10 T-11 T-12 (BAR REINFORCED) T-13 ll H HR II (H-3 mm) H-1/8 H II I H STANDING S STANDING SEAM ANGLE REINFORCED T-21 WELDED FLANGE (ANGLE REINFORCED) T-15 STANDING SEAM (T-21a REINFORCED W.F.) T-14 T-16 RIVET OR WELD H SEE TIE ROD OPTIONS H AND JOINT SPECIFICATIONS GASKET COMPANION ANGLES FLANGED (CAULK OR GASKET) (WITH GASKET) T-22 T-24 —� � —1/2"(12.7 mm) -jr -F H H II GASKET FLANGED FLANGED FLANGED SLIP-ON (WITH GASKET) (WITH GASKET) (WITH GASKET) FLANGE T-24A T-25a T-25b (CONSULT MFRS.) RANSVERSE (GIRTH) JOINTS FIG. 1-4 E M HVAC Duct Construction Standards Metal and Flexible- Second Edition 1.61 oplbSEAM LOCATIONS ALSO SEAL THIS (A) (B) (C) POCKET AT ENDS L-1 WHEN SEALING SEAMS. PITTSBURGH LOCK 2 PQQPO� (D) (E) f L-2 BUTTON PUNCH SNAP LOCK (F) NUMBER OF SEAMS AND LOCATION VARIES WITH JOINT TYPE,SHEET ROCK AND ASSEMBLY PLANS. L-3 GROOVED SEAM ALSO CALLED FLAT LOCK AND PIPE LOCK O SEE L-1 SEALING NOTE. EE FIG. 1-6 ALSO L-6 L-4 L-5 DOUBLE CORNER SEAM STANDING SEAM SINGLE CORNER SEAM LONGITUDINAL- SEAMS - RECT. DUCT FIG. 1-5 S�p(A; HVAC Duct Construction Standards Metal and Flexible- Second Edition 1.67 Lo a 9: ° OJ m U) P-- J a. ��1r' NLn = (D X00 w� Z m O ¢ d W O 2 � ri O r--En (v f-- X 7- z Z Z w Z w 0 :2 Z OZ w V) ¢O U ¢ O �0- ck�(nCy cN,�a�< w Z Z Vl ~wcL-WW _� w� (nQ � LL�j--� >Z_ JwOX0p VO Q H Z = O Q < w 3 Z C:) 0 Uwl N— LL, O O U7 O ' J o< I ~(wn6 Z (L O ' J 00W. Y'9 RONFORCED DUCT FIG. 1-7 S A HVAC Duct Construction Standards Metal and Flexible - Second Edition 1.?� TABLE 1-25 T-1 FLAT DRIVE ACCEPTED AS REINFORCEMENT DUCT WALL 26 ga 24 ga 22 ga 20 ga or Heavier Static Maximum Duct Width (W) and Maximum Reinforcement Spacing (S) Pressure W S W S W S W S 1/2"w.g. 20" 10' 20" N.R. 20" N.R. 20" N.R. 18" N.R. 1"w.g. 20" 8' 20" 8' 20" 10' 20" N.R. 14" 10' 14" N.R. 18" N.R. 12" N.R. 2"w.g. 18" 5' 18" 8' 18" 10' 18" N.R. 12" N.R. 14" N.R. 3"w.g. 12" 5' 18" 5' 18" 5' 18" 6' 10" 610" N.R. 12" N.R. 14" N.R. 4"w.g. 16" 5' 12" 6' 12" N.R. 8" N.R. 8" N.R. Not Accepted 6"w.g. 12" 5' 12" 5' 12" 6' 8" N.R. 8" N.R. 10" N.R. Although the flat drive slip T-1 does not satisfy the EI calculation requirements for Classes A, B or C reinforcement, tests predict its suitability for use as reinforcement within the limits of the table. N.R. --No reinforcement is required;however,the T-I Joint may be used. —AWp� HVAC Duct Construction Standards Metal ,and Flexible- Second Edition 1.71 z mo O g \ � o o ¢ o W om a a a ¢ �Z m W om m2 z J m U J m < �2 OU � ¢ Oz O� WU) U � o r LP WO 0zui W gU U WO ¢ vi \ WQcr m ¢ Q o ¢ O UUm <IZU- Z \\ CL 0W ¢ Wf_ \ Of- � ¢ O mLL CO ¢ U Cn W W o > ¢ —0 - j _ 0 W z ¢ J U z W z O 0 Q j z Z = Z \ 0 > U r z a = � � 0- J :cn W a: (,) -J <W W w 2 W U O m 2 U > o EW of ¢O = ¢ cn E Z cAo � �6 Z 2 w N w U z W ¢ 2 n W 0 3 11Z Q J on W O O Q LL Er ¢ ¢ N Q amoa \ U) y p � W m \; W J Cr ¢ m o ¢ ¢ W U < Y / m o ¢oaW o � oa- ¢m r Cr EWQ z U E m m O 0 Cl co W F- > ' zz COmz ¢ m W W Q /' i U CO w U / Q J ¢ U - CO Q j Cr Fn WW z a E Z m 2 E- � r Uz (n om < LOQ W W ¢ S W 00- m z oar m So J a W U U O r z CR SSBR®KEN AND BEADED DUCT FIG. 1-8 1.74 HVAC Duct Construction Standards Metal and Flexible - Second Edition ( SMQICNA R H W g H TYPE RE 1 TYPE RE 2 RADIUS ELBOW SQUARE THROAT ELBOW WITH VANES CENTERLINE R= 32 UNLESS OTHERWISE SPECIFIED H IS NOT RESTRICTED TO 90°. SQUARE THROAT, W =0.5,MAY BE USED, UP TO 1000 FPM(5 mps). i g H H W R W TYPE RE 3 TYPE RE 4 RADIUS ELBOW SQUARE THROAT ELBOW WITH VANES WITHOUT VANES (1000 FPM(5 mps)MAXIMUM VELOCITY) JW2 4FH 9 R 1 = 3/4 W1 W H R2 R1 + W2 TYPE RE 5 TYPE RE 6 DUAL RADIUS ELBOW MITERED ELBOW BEAD,CROSSBREAK AND REINFORCE FLAT SURFACES AS IN STRAIGHT DUCT PAGE 1 OF 2 RECTANGULAR EE FIG. 2-2 �MQCNA HVAC Duct Construction Standards Metal and Flexible- Second Edition 2.3 000- SEE VOLUME DAMPERS IN CORNER FILLER PIECE FIG_ 2-1 AND FIG 2-15 OR USE GASKET I I STRAIGHT TAP CLINCH LOCK BUTT FLANGE OR CLINCH LOCK li LINED DUCT L L=W/4, 4" (102 mm) MIN. CONNECTION (NO EXPOSED LINER EDGES) W 9 CLOSE OPENING 00,11, Di NOT LESS THAN D2 IN AT CORNERS Di t445' LEAP D DO NOT USE CONNECTIONS WITH SCOOPS. 45 DEGREE ENTRY 0 45' OPENING CUT U'\- ACCURATELY (SHAPE & SIZE) BEAD PROFILE FLANGED OR SPIN IN BEAD VARIES CONICAL K Q NOTCZDH BELLMOUTH FLANGED SPIN IN SEE FIG. 3-8 FIT ALL CONNECTIONS TO AVOID VISIBLE OPENINGS DOVETAIL AND SECURE THEM JOINT SUITABLY FOR THE PRESSURE CLASS. ADDITIONAL MECHANICAL FASTENERS ARE REQUIRED FOR 4" W.G. (100 Pa) AND OVER. BRANCH CONNECTIONS FIG. 2-6 2.8 HVAC Duct Construction Standards Metal and Flexible - Second Edition ;SMA,: OFFSETS 2 AND 3 AND TRANSITIONS MAY HAVE EQUAL OR UNEQUAL INLET AND OUTLET AREAS. TRANSITIONS MAY CONVERT DUCT PROFILES TO ANY COMBINATION FOR RECTANGULAR,ROUND OR FLAT OVAL SHAPES. 15°MAX. W1 w w2= w1 9 L� OFFSET TYPE 1 CONCENTRIC TRANSITION (ANGLED) 9 MAX.45°DIVERGING,60°CONVERGING 60°MAX. �— LJil —� W W W e L� / -T OFFSET TYPE 2 (MITERED) ECCENTRIC TRANSITION 9 MAX.30° (EXCEPT 45°IS PERMITTED L AT ROUND TO FLAT OVAL) W �iq (25 mm) W R=� A 6"(150 mm) Z - 1 5 THROAT RADIUS C i FLANGE MINIMUM OPTIONAL (25 mm) -� V, OFFSET TYPE 3 (RADIUSSED B OR OGEE) STANDARD BELLMOUTH (ON SHORT PATTERN BELL C=3"(76mm) 8=A+4"(102mm)) 00111 OFFSETS AND TRANSITIONS FIG. 2-7 'SMAC PIA; HVAC Duct Construction Standards Metal and Flexible- Second edition 2.9 BUTT HINGE 1"x 1",OR PIANO HINGE I I j I LOCK TYPE 1 FRAME 2 HINGE POS.2 II II SASH II II LOCK II II VIEW PROT FRAME 1 FRAME 3 IF SPECIFIED HINGE POSITION 1 HINGE POS.3 DOOR B DOOR \ A \\\\ GASKET DUCT GASKET INSULATED PANEL ACCESS DUCT PANEL LINED DUCT PANEL IS DUCT GAGE(MIN.) WITH SCREWS AT 8"MAX.SPACING Door No. No. Metal Gage Size Hinges Locks Frame Door Back 2"w.g. 12"x 12" 2 1-S 24 26 26 Sta!ic 16"x 20" 2 2-S 22 24 26 and 24"x 24" 3 2-S 22 22 26 Less 3"w.g. 12"x 12" 2 1-S 22 22 26 Static 16"x 20" 2 1-S,1-T,1-B 20 20 26 24"x 24" 3 2-S,1-T,1-B 20 20 24 4"w.g. 12"x 12" 2 1-S,1-T,1-B 20 20 26 to 16"x 20" 3 2-S,1-T,1-B 20 18 24 10"w.g. 24"x 24" 3 2-S,2-T,2-B 18 18 24 S=Side opposite hinges,T=Top,B=Bottom CONSTRUCTION AND AIRTIGHTNESS MUST BE SUITABLE FOR THE DUCT PRESSURE CLASS USED. THESE ILLUSTRATIONS DO NOT PRECLUDE THE USE OF OTHER METHODS AND HARDWARE. DUCT ACCESS ®®®RS AND PANELS FIG. 2-10 2.12 HVAC Duct Construction Standards Metal and Flexible- Second Edition ; M DUCT SHOULD EXTEND STRAIGHT FOR SEVERAL INCHES FROM A CONNECTION BEFORE BENDING. S`0,•(7 000 / MAX.SAG 1!2"PER FOOT(41.7 mm PER m) OF SUPPORT SPACING FIG.A 0. 000 M MAX.SAG 1/2"PER FOOT(41.7 mm PER m) FOOT OF SUPPORT SEE WIRE HANGER SPACING OPTION IN FIG.3-10 FIG.B CLOSER MAXIMUM INTERVALS MAY BE SPECIFIED AS A CONDITION OF U.L.LISTING,PARTICULARLY IN FIRE RATED FLOOR-CEILING ASSEMBLIES. FLEXIBLE DUCT SUPPORTS FIG. 3-9 3.20 HVAC Duct Construction Standards Metal and Flexible- Second Edition fMpC STRAP HANGERS TRAPEZE HANGERS HANGER STRAP OR STRAPS ANGLE ROD I 60"MAX. UNLESS FOOT I (1524 mm) OF STRAP IS PLACED UNDER A BOTTOM I REINFORCEMENT >< I I I I SCREWS SCREWS MAY BE 1" MIN, I OMITTED IF HANGER LOOPS (25 mm) LOAD RATED SIZE BOLT(S) FOR FASTENERS LOAD STRAP HANGER SECURE 6WIRE ROD 10"(254 mm) DIA.MAX. BAND OF SAME SIZE 24"(610 mm) AS HANGER STRAP DIA.MAX. 36"(914 mm) DIA.MAX_ HANGERS MUST NOT DEFORM DUCT SHAPE HANGER RODS,WIRES I t OR Ii STRAPS II II II II II II II NUTS ANGLES ALTERNATE LOCATION(VERIFY UPPER TRAPEZE LOAD CAPACITY) REINFORCEMENT MAY BE USED FOR ATTACHMENT BAND IF IT QUALIFIES FOR BOTH DUTIES. ONE HALF-ROUND MAY BE USED IF DUCT SHAPE IS MAINTAINED. DO NOT EXCEED ALLOWABLE LOAD LIMITS. LOWER HANGER ATTACHMENTS FIG. 4-4 i jj�MM HVAC Cuct Construction Standards Metal and Flexible- Second Edition 4.9 VERTICAL •' .� FD SUPPLY DUCT SEE FIG. 2-2 /* I I PAGE 3.15 1 I I I I I � ADi 1� I I I I L TABLE 3-2 I � I I V.D. I I I ( I III VERTICAL I I RETURN A x D 45' CLINCH COLLAR DUCT F.O.B. FIG. 2-6 FOR VIEW SHOWN A, C & E = WIDTHS D = DEPTH F.O.B. IS FLAT ON BOTTOM SEE FIG. 2-7 9' C D F.O.T. IS FLAT ON TOP x V.D. V.D. R I I I I III III R = RISE SEE FIG. 2-7 SEE DRAWING SYMBOLS ON PAGE 1.1 V.D. V.D. J L J L p l I I I JJ`L W I I SUPPLY — — RETURN SEE FIG. 2-2 R = RISE THROUGH 2-7 SEE FIG. 2-7 TYPICAL SUPPLY OR RETURN DUCT FIG. 2-1 2.2 HVAC Duct Construction Standards Metal and Flexible - Second Edition Si49M Thermal Systems Balancing, Inc. 7/ 0 11631 Ayala Road Jacksonville, Florida 32258-1607 ® (904)260-4302 AW NATIONAL ENVIRONMENTAL Fax(904) 262- 7390 BALANCING BUREAU TAB Agency and Personnel Qualiflcations President of Corporation Curtis Wm. Smart, T.B.S. NEBB Certified TAB Supervisor Over 15 years TAB Experience AA Degree, Brevard Community College President of Florida Chapter of NEBB (FEBB) General Manager E. Derald Smart, Sr. Over 20 years Construction Management experience B.S. Degree,Jacksonville University Office Manager and Systems Analyst Patricia Truesdale Over 5 years administration experience. A.A. Degree, Florida Community College of Jacksonville Field Office Manager Joanne M.Tudino Over 11 years administration experience. C.M.A., Delaware Valley Medical Academy Technicians Wm. Mitchell Holstein, 10 years TAB experience NEBB Certified TAB Supervisor, 2001 Michael Courson, 5 years TAB experience James Jones, 5 years TAB experience Louis Michels, 2 years TAB experience Thomas M.Truesdale, Jr.,4 years TAB experience Certifications& Qualifications NEBB Air& Hydronic Balancing NEBB HVAC Systems Commissioning NEBB Sound &Vibration Testing NEBB Clean Room Testing ASHRAE Indoor Air Quality ASHRAE Test Adjust and Balance Printed: 12/5/02 Page 3 of 33 Pages Thermal Systems Balancing, Inc. 11631 Ayala Road �.— Jacksonville, Florida 32258-1607 (904)260-4302 NATIONAL ENVIRONMENTAL Fax (904) 262- 7390 BALANCING BUREAU Recent Major Projects International: Torpedo Post Run Facility, 320 Andros Islands, Bahamas Range Support Shops,Andros Islands. Bahamas Command Control Building 1604, Andros Islands, Bahamas Arts and Crafts Facilities, LaJes Field,Azores Portugal Building T-714, LaJes Field, Azores Portugal Vehicle Maintenance Shops, LaJes Field, Azores Portugal USAF Officers Club, LaJes Field, Azores Portugal USAF Hazard Maintenance Facility, LaJes Field, Azores Portugal Dormitory SNCO T-163, LaJes Field,Azores Portugal NASA: VAB Utility Annex, Kennedy Space Center, Florida Solid Motor Assembly Building, Cape Canaveral Air Station, Florida Canister Rotation Facility, Kennedy Space Center, Florida Headquarters Building, Energy Conservation, Kennedy Space Center, FL. Launch Complex 39A, Chiller Replacement, Vehicle Assembly Building, Kennedy Space Center, Florida Chemical Testing Laboratory, Cape Canaveral Air Station, Florida Military: Winn Army Hospital, Fort Stuart, Georgia Building 989, HVAC Upgrade, Patrick Air Force Base Building 127, Replace HVAC, Norfolk, Damneck, Virginia Dorm Upgrade, Barksdale Air Force Base, Louisiana Plasma Spray Vent, Building 794, Naval Air Station Jacksonville, Florida Hazardous Waste Facility, Naval Air Station, Jacksonville, Florida Government: FAA Air Route Traffic Center,Albuquerque, New Mexico Florida Solar Energy Center, IAQ Survey, Cocoa, Florida Duval County Courthouse, HVAC Modification, Jacksonville, Florida Duval County Public Schools, Jacksonville, Florida Brevard County Public Schools, Cocoa. Florida St. Johns County Public Schools, St.Augustine, Florida Volusia County Public Schools, Daytona, Florida Commercial: Orlando Utilities Comm. -Stanton Energy Center, Orlando, Florida AT&T Universal Card Center, Jacksonville, Florida CSX Transportation Corporate Offices, Jacksonville, Florida Disney-MGM Movie Studios, Lake Buena Vista, Florida Florida Power&Light, Rockledge, Florida Computer City, Melbourne, Florida Other: Mayo Clinic of Jacksonville, Jacksonville, Florida St. Vincent's Hospital, De Paul Building,Jacksonville, Florida Printed: 12/5/02 Page 4 of 33 Pages 0 ° Orn 4 z � a W- -Y � -i , d Im_ o •OQ� b � (7 N Ho CA to LAJ 7a � o st ,cn 1 6 os• r*I droll cn o � � z o � IF a o0 s n � ET cn o ,� .ir 11 r-Q � r o 0� a N CZ r rr"nr on 0 z b ° �.. Orl NJ ,S -n (n 00 • , to � Cry i 1 fi :•11'rJ•1�'r.•t•'r_:I�rr:.1�V:t�li:t�lr_I�li�l lr}I•li•.t1r•.1Ir_.1•li•.��V�.11 Q A#I )C.1 lr;.l I/_.t r 1 • •• ••••• ••••: .••..• •••• .••.;•��••.,••..••,.••..••�••••�•. �" ,ir_•IAV:.I,Ir).111_•d•li•.Ifli•.I�Ir;d�li•.111i.t�lr,.1111 r �r:•.�:,•��rr•��n•�Grh�rl•r�hh�rUitiil•r�:'lh�rilt�rl�rull,Irl•��.vl�tirl•��:Ilnil•i�%I•�.`ri•��•.l �•�r11��1�i'�Zil��rl��q�� • Itl tate. ' � 'I�►i . . �.. 1=13 :i• • �1'li ce rtify from the records of this office that THERMAL SYSTEMS �(=li `•l=I BALANCING, organized awsof the State of filed on January 22, 1982 . • • • The document number of this corporation is F64135. (�I ..,• sl�li I further ISIS that • corporation has paid all fees due this office throughDecember 3 1, 2001, that its most recent annual report/tiniform business report a=l� 200 .ISI: I further certify that said corporation has not filed Articles of Dissolution. sl�l • • •'•l D �lsle •..• '• Giveii mider my hand ami tile +I=liGreat � • • • �' Seal ofthe State of • 1 at Tallahassee, the Capitol, this the A Eighteetith day of January, 2001 • • ••1 rt 1i,• ;lel, I • • ' P.Mol • • ?;I�I • �I'li '.Illi i•rr,,t�lr'.I,rr:.t•Ir:.1•rr•.1•Ir'•'•Ir•.1•Ir:.1•li••1•li•.1•V:.1•Ir•J•Ir:.1•rr:.1•li•.i•Ir:•1•V.1•Ir:.l•V:.I,Ir•,1•Ir:.l�l!•.1•r,•.I�Ir:d�b..l•rr..r•I t0 Ir\t 1 Ir �l=li r�h�rr•r:rr•��r�•Nrr•�Yrl•:err•:Irl•�:rlh�rl�r�ri••�N•rCr/hurl•��ilh�rN��r1�:�•��rr•r�r/hul•.�rrh�rl•.iri••�ilh�rlh�r I�•.�rrlr�rl•��r!•:�i�l.� AGO-110. CERTIFICATE CSF LIABILITY INSURANCEr„SDA If!(MtdlUI11VY) RM 1 _ 02/28/01 i�iiiiiiiir?�-li TRIS CERII�I(:nl E IS ISBLJFU AS%�Mnll r_12 UI INI=012M111ION It l:r.vnrll .l llnllrnllc!] k Ml�tg..,Itte. ONLY AND cotvCR9 NO RIGIIfS Ul'UIJ'fLlr CF_f?IIFICn1� P.U. Dox 37.0770 IIOL.DE11. 1IIIS CEI?III-ICAIEDOES I,Ir)I AM1:1,11),I?X11=1,11-11Oil -0 11. Atlantic Ave AL1 ER TIME COVERAGE AFFORDED IIY_IIIE I'OI.ICIES IIELOW. _ OP11-:on 11ench FL 32932-0770 ,one- 321-703-2404 Fax1321-784-1055 INSUREIZSnFFOI?I)I1,1(;COVEI?n(,G nc:nla 11 114SUIIEIIA: American Indemnity Company ulsuRrltn: Plverent 2lntiot)nl Innlu:nnco Co. I'lleYtllal. uy nteme Balancing, Inc INSWICR c:_._ .._11rogreanive OoBlpatJien 11631 Ayn1.a Road INSUI1r:RD: .1nr.ltri ntv.I.l.1n FLr 37250 - - INSU1111111 121: f;OVI:I?Al3ES 1111 rift wars rtl-IfISIIItANCF I.IS Ir:O nrI.OW I IAVF KEN MrOrO 10 11117 lNalltr-D NAMED AIIUVF roll 111F POUCY PERIOD INDI(:A 11111).NU I WI1111InuU11)(: --•- - AI h 111 U111111'MI'll1,I rI tM Off CO 1111 N)N 01'Af lY CON I IIAC I Olt 01111:11 DOCIIMrII l W1111 I1F31'FC I IU WI IICI I I l 1f!1(,rill If ICA I r MAY 1111 I!V;I If 0 r fR Llnr I'VII IAII1,I I It:If19OIlAf ICF ArronnEn BY if IF PoI.ICIEs DF-SCOInED 11E11EIN IS SUBJECT 10 ALL I HE 1 ERMS,EXCLUSIONS A140 C014131 110113 Or SUCI I 1'1 n WIFS,AQ0IiF(3AIF HMI I n MIOWN MAY IIAVP nrrN npriucrt)nY I'AIN CLAIMS, dCilt - --— --_ _._____.___._.._._�--. .1 u� 1`1141 V 1 G t:11Vr 11011i�V r IIIIIA 1101 IRt IYVFOf INSURANCE POLICY NUMBEII bRA Mhi/ UiYY UAI MM/UU/VY IIt'll IS rll111AMI,LIABILIlY [ACIIOCCU11lEfICE s 100U0U0 A X +:OMMFR(.IAL G611f_RAI.LIAIIII.I I Y 850312692/27/02 rmE VA (Ally ono Ill $ 10 0 0 0 U 2/27/03 .. ..._..._ .......___.._.-.. CLAIM.^,MADE I R I Occult MUD EXP(Any one person) $ 5000 PERSONAL BADV INJURY s 1000000 (11!111:IIAL A00111W I r- 12000000 (;I Ill nr;nurr)ANl1Mill APl'Lu:3P1a1: PPODIIf:t3•COMPIOPArn s 7.000000 - r1-?D• VVI ICY I x I I L LVC AtIII16101111I:LIAIIII.IIY (Pn ni- lr:u 1ur,I r:I nal l s 1.,0 0 0,0 0 0 O ADYAUIO 04439000 12/27/02. 2/27/03 I (rfn llf'lr.l) I At I.OWI IFD A11 f OS 110011”It I'll My IP,•r per;nn) t X SCI IEVULEV AU I0S X HIRED AUIOS I I)UIill.YI11.11.)Illy _ (1,e.1 ncclllents X noLLowlar:u nu t os ----.._-- ...._.-i _ I'Rr ti'1 It1 ncUnIdAtli'. S (l'er cldei dl AU 10 ONLY•rA ACCIUrN I s nnnnrr LlnRll.l I v Al1Y Al 11-O 1-1 OIc11 I I IAII rA AI97 S All 10 01ILY: AGG $ 1 YCrSS t lAIIII I I Y I I FAC110CCuftllrfRX s _ - 1)CClllt I I rA AIMS MADS I A001 10AII' T• Ill lit If:Ill lit' .. it.11a11IoN—s_ s VJt'Srhllr. rlllr. - - w•gtLI:ItSr;OlAl'FI19ntIOIIAND IoI1YI,IMllt3 ,x,1.1111 I GII'Ir1YFR3'UAIIILIIv ILL,FACI I ACCIDENI s1000000 -- n 7700007(133-00]. 12/1 /02 12/1 /03 - E.L.DISEASE-FAriMl•LO1r:I' s 1000000 P.L.DIFICASE_I'OI.ICV I IMI I s 1000000 I I n rrt.............I ISI l r n•01'100 1 IUI EUI VCA I IUtJ3NE1IICLE3IEXCLUSIUIJ9 AUUGD BV ELJUOIZSEMFIJ 1/SPECIAL PNOVI31UIJ3 (,I--I t I IVICA I E I IOLDER N ADDU IONAL INSURED;INSURER LETIEll: _ CANCELLATION -- SNOULD ANY or'l I IF ABOVE 011:50WIFI)POI ICIF S RF CANCIA I Ill 111;1 utlr: I I II? EXPIIIAIION DAIS 111r11FOr,11IF ISSUING IIISUP"'W+L1.FI11)IiAVOIl 10 MAIL 10 DAYS WRI I I EN NO I ICE 10 111E CEIZ I II ICA I F I IOLUEJI I NAMED 10 111r: LEFT,our FAILURE TO DO SO SI IALL IMPOSE NO OOLIGA1ION ON t-1A011.1I Y Or AIIYKIIIDUI'Otllllrlll9 Illilt,l//AUl:tl1(1O 1111-11 !1r.IIIAIIVI' I _ Willia)n D. 0 d ni;()itii JG-S(7197) ACOIIU :Oltl'OIlAIION 101111 Thermal Systems Balancing, Inc. 11631 Ayala Road 131 Jacksonville, Florida 32258-1607 (904)260-4302 NATIONAL ENVIRONMENTAL Fax(904) 262- 7390 BALANCING BUREAU Instrument Calibration Instrument Applicadon Serial , , , Shortridge 860 Air Data Direct CFM Differential Multimeter/ Pressure M00500 11/12,01 Micromanometer Shortridge HDM 300 Water Pressure I W02021 2/25/02 Hydrodata Multimeter Differential Readings Shimpo DT207B Photo RPM Readings 79806055 1/29/02 Tachometer ACO Sperry Clamp On Amperage/Voltage 2KO505583 10/1/02 DSA 400 Readings Vel-grid Anemometer LCA Air Velocity Readings A34490 2/14/02 6000 Industrial Instruments 22012 Psycrometer Humidity-Wet/Dry Bulb 19232-1 10/21,02 Omega H22 Pyrometer Temperature T-228031 10/1/02) Bacharach 16-9001 Florite Air Velocity Readings 16-7001 10/22,01 Air Velocity Meter Thermal Systems Balancing, Inc. Ni ,B 11631 Ayala Road Jacksonville, Florida 32258-1607 ® (904)260-4302 NATIONAL ENVIRONMENTAL Fax(904)262- 7390 BALANCING BUREAU Certification Project: Suwannee County Courthouse Location: Live Oak, FL Scope: The data presented in this report is an exact record of system performance and was obtained in accordance with NEBB standard procedures. Any variances from design quantities which exceed specified tolerances are noted throughout this report. Air Balance: The air distribution systems have been tested a b and final adjustments made in accordance with NEBB "Pr d al dards for Testing -- Adjusting-Balancing of Envir t s" and the �,.. project specifications. NEBB Contractor: Thermal Systems Balancing Reg..vo. 273-? r Air TAB Supenisor. Curtts t Hydropics Balance: The by ni dis ste have en tested and balanced and final ad de a ordance wi NEBB "Procedural Standards for Testing -- alancing of Environmental Systems" and the project ecifi NEBB Contractor. Thermal ystems Balanclna. Inc. Reg—\o. 2734 _ Htidronics TAB Supervisor: Curris Win. Smart Submitted and Certified By: TAB Supervisor Curtis Wm. Smart Date Thermal Svstems Balancing,Inc. Reg.No.2734 Thermal Systems Balancing, Inc. 11631 Ayala Road BIB Jacksonville, Florida 32258-1607 ® (904)260-4302 NATIONAL ENVIRONMENTAL Fax(904) 262- 7390 BALANCING BUREAU Certified Test -adjust and Balance Report Heating, Ventilating and air Condition Systems� Test and Balance Procedures and agenda The following are the Test&Balancing survey procedures for this project: Air Balance: 1 .) Record fan and motor nameplate data. 2 .) Open all registers and diffusers. 3 .) Check duct for air leaks. 4 .) Check fan rotation and record fan rpm. ,>•► 5 .) Record motor amperes. 6 .) Record total static pressure of fan. 7 .) Make Pitot tube duct traverse of the supply ducts. 8 .) Adjust fan speed to obtain design CFM. 9 .) Balance supply and return outlets to design quantities. 10 .) Adjust outside air. 11 .) Check and record final motor amperes. 12 .) Make a complete static pressure profile of the air handlers. 13 .) Take and record the wet/dry bulb temperatures of the supply air,mixed air and outside air. 14 .) All work shall be done in accordance to NEBB standards and the results reported on appropriate forms. Ate''. Curtis Wm. Smart, TBS Certificate#2734 Page 15 of 33 Pages Thermal Systems Balancing, Inc. N H B11631 Ayala Road Jacksonville, Florida 32258-1607 ® (904)260-4302 NATIONAL ENVIRONMENTAL Fax(904) 262- 7390 BALANCING BUREAU Certified Test Adjust and Balance Report Heating Ventilating and Air ConditiarLSystems Test and Balance Procedures and Agenda The following are the test&Balancing survey procedures for this project: Water Balance: 1 .) Set up job on standard NEBB forms,as per plans and approved submittal. 2 .) Open all balancing valves. 3 .) Set all control valves to full flow. 4 .) Check pump rotation. 5 .) Check and record motor amperes. 6 .) Check and record pump TDH. 7 .) Balance all coils to design GPM. 8 .) Set bypass. 9 .) Check pressure drop across chillers. 10 .) Record chilled water temperature entering and leaving coils. 11 .) Adjust water flow to cooling towers. 12 .) Record water temperature entering and leaving condenser. 13 .) Record condenser water entering and leaving cooling tower. 14 .) Record wet and dry bulb temperatures of entering and leaving air of cooling tower. 15 .) All work shall be done in accordance to NEBB standards and the results reported on appropriate forms. Curtis Wm. Smart, TBS Certificate#2734 Page 16 of 33 Pages C . C . BORDEN 1CONSTRUCTION , INC . 904 - 354 - 3458 PHONE 904 - 354 - 4770 FAX FACSIMILE TRANSMITTAL SHEET TO: FROM: Don Ford Allen Borden COMPANY: DATE: Atlantic Beach Building Dept. 1/26/05 FAX NUMBER; TOTAL NO. OF PAGE'S INCLUDING COVER: 247-5845 3 RE: Atlantic Beach City Hall Addition &Alterations O 1_171GENT CEJ F0 1t R1?Vii{W 13AS RFQU14SI'1.'.1) NOTES/COMMENTS: Please see attached per your request. 1019 RosseIle Street•Jacksonville,Flozida 32204 Jan 26 05 10: 55a CERTIFIED HIR CONTRS iNc 904-389-4SR5 P. 1 ce'rtified, -q-Lr Contractors, Inc_ 4505Marquette Avenue Jacksonville, Florida 32210 Phone: (1304) 389-7940 Fax: (304) 389-025 DATE; PAGES: -Tax TO- /4-14 r--j FROM: FAX; FAX: (904) 389-4925 PHONE: r PHONE: (904) 389-7950 RE: 0 uRoENT U FCR R"L"N ❑PLEASE RELY 0 PLEASE COMMENT COMMENTS: e, J4A1 2 Jan 26 06 .10:55a CERTIFIED HIR COMTRS IMC 904-389-4925 P.2 JAN 26 2085 1128 FR CARRIER FLORIDA 904-WIS48 TO 3894925 P.02i02 Product Data: oroaz-glows IMPROVED: Husky Coll Coat - Dip aMna WWV Huslq ON Coat now dip farredWoe k e WU*W.Mn aMselae fewaanrlt oostlrng wAh aupolor adrenbn.Cull Coot won't 0**.do or Atka.Cod Coat is dlp sealed only at Bsonz-Glow Llwnwd ln-mmam CUW1rq bdMkm prier b ws109 wa wnplay■awal bip.prey amewa►sultsoe dear"end condW Yp pnx w a 4cWnMe a ellen CA flee awrfans and apply an anpsMpatfa clsmio*borated coaft t+eSbrml for mKondmT comeNon rasidsrloe and k"FMVW WWWL Musky Wl Coal P*Wft far Nlbe and doom ao"Ape harsh aserlel end Nlduanlal 4nmkon nerrfn.Csfi Can Wo ill dadldly$*$no and oomteea at eye amw moi so 1M bw aisoye 10 p�olnel%IN(uN FN ntrg4 0"a 0011 rt WOW quan9 09"aorardw _._.. eNcic tweed by hatch 06 IDIOM*dnVkww smn.Hweky Cell Cao has neyaglhla aAIRx on Anal VWW$r end It regnlrad.pan be only rewind in tele flaw.Nift red Ccet,bsc.we of fill unklm t(OW lea,.nearm ihs beet oven ll cormim Protecton M tele m~.oudrq ao deer"ana a dhg p vee"Coll Is never arb0&AW b lemperalwae above Coo P Vda ombm txame and sorrier plift 4an heat aaaas whidr cen occur dunnq M9h larnpa mUo IAamlweet auAnO:OW46410w Coil CON DIP Phx4m Csuwante00 I W%Coverage, 0011 Coat Oto M haleh e0reatvs 4rK!o0traalvo awe pherae of Celt all,hy01o{i1N1 nulRda,hyde0ddoric add.ammOna. end o 40"among many a1i"m Uva no prowl equk*wm Placed In evdar MfAo ae,MGM 16mana.peeoaan ralineAss, crawled end d+wmooeuaov pi ft,bed OW allow mina&paper moll,abeel nMHa,was*vow b aan o I fac11(es.lunrt saysud sydams.vebnlilmn iadlllae.omdw onl pamn,swllran"pool vamoePharom.sew ndpa.e*board syMaws.hotels, rrallNar hoa0liata, 16011NA ft.CEWNWO0r1 pentane, g mppNrp rile.aUporh, low/tud 9eneraang almde s and many/ower swore cora"envilwwrimm. ddt[Y COL COAT OWACMML 90rr92don 256% Opmwv Tempsrdw a Range(Ory) •SO 1s+zip 014L F. W Ramo.Froaear n 1."" U.V.inhbiler In FAm Coat 10 Year plena.sun Adhesion Propnrtlae &wrlor AbOOM Aadalatran sapettor Heal Tmrlater Dagrirasa0n tesiftab Ozome Deemer No SWA)r Swtkft Acid Fumn Tannic Acid Gh*Mo sae water Calc AGW Amm Me Alomm Cee Add Fain H26 Pumw Chbidae HCt.rum" N bic Add HP Add Su*jft Add Utk AcWUnm(autatimm or u*w from dap,cabs.bada A"IM.WW M> FMONcoc against Cow oo mim sbmap ems- EFFECT ON TAT TRANSF011 DEGRADATION: Yost showed no 4"Ne aArsd(rose ton 1%) GAS C111tOIMATOGRAPHY T=r(FIO)'TOM aiM na MZetd0114 0r 101dQ gaaae M iomlm Stier W ling SALT SPRAY TAT: Paaead 6.000 howa,ASTM8117AIS(C)EM T460 AMJCATN7t(METHOD: Dip Tatra Prvosaa.Cd Coot Is ordy 4ppWi et Erma-Clow In-house em"fm PON Brom-Glow. • r. JAN 2 6 2005 RORDEN ..•NSTRUCTI(?1J.Jvc. ** TOTAL PPOE.02 Transmittal Letter C.C. Borden Construction, Inc. To: City of Atlantic Beach Date: 5/2/05 Attention: Don Ford Project Title: Atlantic Beach City Hall Additions and Alterations City of Atlantic Beach Project #0304-12 CCB Project#0405 Gentlemen: We are sending: ® Herewith the following: ❑ Shop Drawings ❑ Under separate cover Via: ❑ Courier ® 1St Class Mail ❑ FedEx ❑ Other r1ies Descri tion Pre ared BInformation on A/C Equipment Certified Air Contractors, Inc. ❑ To Architect for approval ❑ Approved as submitted ® For your use ❑ Approved as noted ❑ As requested ❑ Returned for corrections Remarks: C.C. Borden Construction, Inc. By: Allen Borden — Project Manager 1019 Rosselle Street / Jacksonville, FL 32204 / 904/354-3458 / Fax 904/354-4770 Rpr 20 05 11 : 12a CERTIFIED nIR CONTRS INC 904-309-4925 p. 2 CERTIFIED AIR CONTRACTORS, INC. 4505 MARQUETTE AVE JACKSONVILLE, FLORIDA 32210 STATE CERTIFICATION CAC008251 (904)389-7950 .. Cr I li;.i (904) 389-4925 Fax April 20, 2005 2005 Mr.Wayne Mclnturff ` 1:3ORDEN C.C. Borden Construction, Inc. ' '''{[?C)TION, INC. 1019 Rosselle St. Jacksonville, Florida 32204 RE:Atlantic Beach City Hall Dear Wayne, Please accept this letter as a follow-up to our telephone conversation on Friday,April IS, 2005 concerning the existing A/C equipment at the above referenced project. Per the plans and specifications we relocated the existing condensers. The plans called for us to connect to the existing refrigerant lines.The total line set length after moving the condensers was less than 80'; therefore increasing the line sets were not recommended by the factory. These condensers were in poor to fair condition, The salt air had corroded the coils, and upon start-up we found high head pressure.In addition the evaporator coils were dirty and need cleaning. I have attached copies of our service tickets for your use. If you have any questions please feel free to call me. 25incereI , G'v � Wes y G. Wilson Sr. Vice President APR-20-2005 WED 09:59AM ID: I-Ipr eu un 1i: iea ULKILFiLLI HIR CONTRS INC 904-389-4925 p. 3 - -- CERTIFIED AIR CONTRACTORONC. HVAC 4505 Marquette Avenue SERVICE ORDER JACKSONVILLE, FLORIDA 32210 (904)389-7950• fax(904) 389-4925 State Certification #CACO 08251 STYPE UwTf TYPPEE+ .,L, urLry BILL TO .. ., .... .. ,( IAAK¢ MAKE }, ,, ,e. 'AD= MODEL 'go FS'36 SERIAL xU /y,/ J �j J SERIAL hUMbER/'� ry1 J / / V V ?4�� 1 / sTRAEr ENViRONMEtVTALCHECKLIST WORK COMPLETE YES242f NO K) S WORK PERFORMED CITY. TYPE/DISPOSITN FOLLOW UP REPORT YES 0 NO L-1, YMQY6 CCT.'iKGT C 9ECOYERED j REcvcEO DISPATCH# TF wCt0.1. ApTHOR3eO W L3 RECLAIMED �J U jos W SK TO DE PERFORMED I7 RETURNED M- cusroMER D DISPOSAL P.O.# C CHANGED OUTIREPLA000 OTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT P- LBS. ' t 01 005. t .r, a Ott Ei4 }riSlITUUT ONt INS:• - �. ... ..ziri .. TOTAL MATERIALS HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS TOTAL LA13OR LIMITED WARRANTY: All materials, parts and TERMS equipment are warranted by the manufacturers' or TOTAL SUMMARY Shoula either party employ an nllomoy to irst wio suit or demand arbitration to enforce any of suppliers'written warranty only.All labor performed the Worisuru fwroot.to prowo tts interest in any manor wising under';his agreement.or to by tho above named company is warranted for TOTAL col'c3 dn""Wos for eTe breach or inn ag-cement cA to tec"Aw on a"sty gond"n tY a ZO days or as otherwise indicated in writing. The MATERIALS ,aitp uhoor this agreerner.t.the proralliag oarly shall be entitled to recover reasonable above named company makes no other warranties, I TOTAL ' ationay s lues.coats.Charges.exporwes.and iniorest oxcen000 or incurred therein' i express or implied,and its agents or lecnnicians LABOR I Kiva AlnhornV in uraar Re wnrk oallmep ubara KINci me been essarAerorly.xxnpwree.1agree ear �wWN nluu.a tido to ryvlrxrM:rNmnler:tN Wrnithed anlrt Mel P:r/mr 4 k:mndo,n PaymnN is rpt mwrla are not authorized la make any such Warranties on 'm pgni 1._u11vr can wrrnva:;md wwprnunt mnWnala a1 Sutler's expense.Any;tNnage iLsunlAO- behalf of above named company. int.,a•o reraavy,1211 ten Le thR respontitu lily ul Seacr. uHC�r7i�0 L. REGULAR I_ WARRANTY Ihsputcn. 'O0 om,xeletl: , i 040 % SERVICE CONTRACT I O - �— !mac°�'t�-� t JratixtJ��Iu, TOTAL,l APR-PA-PAPS wpn 1 A:AIIAM Tn: onrr.� Rpr 20 05 11 : 12a CERTIFIED RIR CONTRS INC 904-389-4925 p. 4 AC. HVAC CERTIFIED AIR CONTRACTORSERVICE ORDER .. 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904)389-7950- Fax(904) 389-4925 VE D State Certification #CACO 08251 {� �.�I TYPE UNnI ^r PE LLYIT• i3� If�j �} S BILL 10 i r 4 G• 9A i 41' C yy]�r ��yy[tt�;••AA'� MAKE rMKET/ ;c N ,pR.(JC110N, IN 5BiR 00 '35-30 1E e0,P5-30 SERIAL NUMBER SERIAL NUMBER NANEr �- o�a�••.23 9?z o8'�>�C 235').;" ,:rpaeET „ GArE 9�6 S n' �Q ENVIRONMENTAL CHECK LIST•, WORK COMPLETE YES X NO 1-, crry WORK PERFORMED QTY. TYPEJDISPOSITION 32 FOLLOW UP REPORT YES❑ NO❑ PMOAE CCNg1Gr 'C RECOVERED C RECYCLED DISPATCH Il 6-2 a r rEC N.GIAN / AU7NOFIZEDSY 1.3 fccl Mho �J JOB fr nErUR IWAKIOPERFORMEDEPERFORMEDU UMPOS ED CUSTOMER CL 1..PosAL ]DISMANTLED 7 CHANGED OUTIREPLADED QTY. MATERIALS&SERVICES. UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFAA5RA rR- :Z2 Las. �`�' S7'O"'�. �1r7-c+C..�,G„�� --�Q.r.,,.�v/?Z •��' t , r TOTAL MATERIALS u' HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS' TOTAL LABOR!: LIMITED WARRANTY: All materials, parts and t TEraas equipment are warranted by the manufacturers'or TOTAL SUMMARY { Should odhor parry employ an attorney;o instllu:e svit or Carlen areitration to enforce any of Suppliers'written warranty only,All labor performed Cha rrovislons hDrcol,to proma;3 inlyrnsl In any mailer arising,:ncw this agreement,or to by the above named company is warranted for TOTAL colWct.l..omgas 4x the aloha•.N this casement at to l=ver m o surely bond even by a 30 days or as otherwise indicated in writing_The MATERIALS party u•I for this agreurnom,11r)prevailing party shall be Rndllcd to recover nrasonawa TOTAL tnlornoy's loss.casts.chargos.expensas.and Interest expended or incurred therein. above named company makes no other warranties, LABOR I1v,voiA,tt tvto Kccrtt•oww%oul"Ki::awewhchh.a;coea:-W tactor" express or implled, and Its agents or technicians y cnmpurtae.1,Gree tn:u are not authorized to make an such warranties on l :ilxtnr rea,N1&UIR:l,l Utiu'PlrKln•1mxlgflJlS ip�nlGled 4:[II I:nili 1MymC�n1 IS Rade.II eoymanl ie/lel alael' Y Irnavl.0.1or all TIPO ,said f.•qulpmwilwalerial„,d Saileis expense.AnV t:amxpa rosu,lng behalf Of above named company. ,aa onrnva.xtu.N aul to N.n r—Palwmilay ct Sckr. REGULAR _ WARRANTY Oispulc Com ted: CJ f SERVICE CONTRACT Dgad(i�, TOTAL t APR-20-2005 WED 10:00AM ID: Hpr eu ua 11 : lea ULKI 11- ILLI HIR CUNIRS INN 9034-389-4925 HVAC � p. 5 CERTIFIED AIR CONTRACTORSu44C. 10 SERVICE Q��R 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 • Fax (904) 389-4925 State Certification #CACO 08251 tYPE UNIT,' TYPE UrnT♦ BILL To s �� MAkG '� 'AAKE MODEL MODEL SERIAL NU61DE14 SERIAL NUMBER `IAMGLOCAi n :;rPEEi OF DATE /.Z ENVIRONMENTAL CHECKLIST WORK COMPLETE YES r: NO G1i1' r WORK PERFORNM CITY. TYPE1o18POsMON FOLLOW UP REPORT YES O NO[: PyONE a CON'ALY '�RECCVL'PEO . IC RECYCLED DISPATCH# 15—2 3 g TF_CI I AfrrNORIZGO DY 0 ftCLn;MEO JOB:t y WORK TO N PeRPOPMtar f7 REYut4rED ❑ptwoanL CUSTOMER C Dish ANTLEO C CIIANGED OUTr.9EPLACED CITY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT R• � LOS. Jam/ 41 lk— • I - ,'P,S, 130 ,71 . f G i — ¢ TOTAL MATERIALS HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS i TOTAL LABOR LIMITED WARRANTY: All materials, parts and TERMS equipment are warranted by the manufacturers.or TOTAL SUMMARY Showd either party emp;oy An attorney to institule suit or demand arbilraagn tO enforco any or suppilers'written warranty only.All labor performed lho previsials horool,fD prdect its interest in any matter arising under:his agreement,ar to by the above named company is warranted for TOTAL collect damages!Or the ueach V tris aweotrwnt Mto recover Oil a surety bond given by a 30 days or as otherwise indicated in tvrlting. The MATERIALS party undor mis agreemew,'.ne Drevailing parly shall be enbtleo to recover reasonable TOTAL above named company makes no other warranties, e+torncya lees.costs,charger.mpenses.erd interesl expenDDo or incurred therein. LABOR express or Implied, and its agents or technicians 1 naw.tumidly Mr rurkv 1hR work Duninou aWwr wlntxl r•ox neon ser m unci ily complwrnd.1 not n that Srrear retains two to wguipmcnVnl:+tarials`.+mahAtd.mCi:fYlal payrmrt is mr+da.it paymRnt u Iwl made are not authorized to mala:any such warranties on - as awreed,Solver can n'movo orad nqulDmenYmatonals al ielbo&espanso.Any dumugo rosulenq behalf of above named company_ ,ort,said nsnaval uMN rwt ho Cho rospo;f$,b ty 0 SDIIDr. Y r o 10 REGULAR 3 WARRANTY Disaster 0 Cunmploted: S 7 SERVICE CONTRACT Iu::xfiu r.DH'.Nnnnre ra-D '•.Jf1Ct�Jbw TOTAL APR-20-2005 WED 10:01AM Tn: onr_c.c HVAC CERTIFIED AIR CONTRACTORS, INC. SERVICE ORDER 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 • Fax (904) 389-4925 State Certification #CACO 08251 I, TYPE UNIT# TYPE UNIT ' RILL To s,��,r- � � �,,� y MAKE . MAKE �• 388 00'9530 M 0085"30 SERIAL NUMBER -PR t}�.�'�C?.7 SCaAEL NUM �JCr23 E [IoC o6 ` iy DAT ST ET ^ n y`-/al(JKw TE ENVIRONMENTAL CHECK LIST WORK COMPLETE YES)C NO CITY \7 Z�f 12- 2 -3 ! WORK PERFORMED QTY. TYPE/DISPOSITION FOLLOW UP REPORT YES El NO El J,C^. .l ❑RECOVERED _,_._..�._....... PHONE CONTACT ^ [I RECYCLED DISPATCH# G/ TEC MCI N AUTHORIZED BY IV1 ❑RECLAIMED JOB# WORK TO B ❑RETURNEDE PERFORMED CUSTOMER ❑DISPOSAL P.O.# ❑DISMANTLED ❑CHANGED OUT/REPLACED CITY MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT R f I_BS. ter;�t 1 -;' .s;,._ .—�L�yL.y�S;"F,�. ..-�.. cyy.�F ✓l.�+C��L�'f'� / _ 10, ------------- , .,.ti�.-------� -.----------e TOTAL MATERIALS x_- HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS r TOTAL LABOR LIMITED WARRANTY: All materials, parts and equipment are warranted by the manufacturers' or TOTAL SUMMARY TERMS Should either party employ an attorney to institute suit or demand arbitration to enforce any of Suppliers'written warranty only. All labor performed the provisions hereof,to protect its interest in any matter arising under this agreement,or to by the above named company is warranted for TOTAL collect damages for the breach of this agreement or to recover on a sure bond given b a y g MATERIALS Ty 9 y 30 days or as otherwise indicated in writing. party under this agreement,the prevailing party shall be entitled to recover reasonable above named company makes no other warranties, TOTAL attorney's fees,costs,charges,expenses,and interest expended or incurred therein. LABOR express or implied, and its agents or technicians have authority to order the work outlined above which has been satisfactorily completed.I agree that are not authorized to make any such warranties on Seller retains title to equipment/materials furnished until final payment is made.If payment is not made as agreed,Seller can remove said equipment/materials at Seller's expense.Any damage resulting behalf of above named company. from said removal shall not be the responsibility of Seller. r ❑ REGULAR ❑ WARRANTY Dispatc % Comp ted: ❑ SERVICE CONTRACT TOTAL t HVAC CERTIFIED AIR CONTRACTORS, INC. SERVICE ORDER 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 • Fax (904) 389-4925 State Certification #CACO 08251 i TYPEUNIT# TYPE / BILL TO 4": 3 SoL, / . MAKE_ MAK/ -30 Fs 36 i Sc�AGar �3�7� 75 g NAM L STR L(/�TyjD+)Nf� t sTr►�"�+f l•�JKe'�T'r.r.+ "�_- it DATE T ENVIRONMENTAL CHECK LIST WORK COMPLETE YES❑ NO CITY_ _� / WORK PERFORMED CITY. TYPE/DISPOSITION FOLLOW UP REPORT YES ElNO L_ 4 '"JL�'�7�/ C.•`'LL LJ RECOVERED f PHONE CONTACT ❑RECYCLED DISPATCH# TEjHNIC AN AUTHORIZED BY ❑RECLAIMED u/� JOB# ❑RETURNED WORK T09E PERFORMED CUSTOMER ❑DISPOSAL P.O.# _]DISMANTLED ❑CHANGED OUT/REPLACED QTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT R- LBS. d 64 _yam yy� . c�1Ttu_ TOTAL MATERIALS HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS TOTAL LABOR LIMITED WARRANTY: All materials, parts and equipment are warranted by the manufacturers' or TOTAL SUMMARY TERMS suppliers'written warranty only. All labor performed Should either party employ an attorney to institute suit or demand arbitration to enforce any of TOTAL the provisions hereof,to protect its interest in any matter arising under this agreement,or to by the above named company is warranted for MATERIALS collect damages for the breach of this agreement or to recover on a surety bond given by a 30 days or as otherwise indicated in writing. The party under this agreement,the prevailing party shall be entitled to recover reasonable TOTAL above named company makes no other warranties, attorney's fees,costs,charges,expenses,and interest expended or incurred therein. LABOR express or implied, and its agents or technicians I have authority to order the work outlined above which has been satisfactorily completed.I agree that are not authorized to make any such warranties on seller retains title to equipment/materials furnished until final payment is made.If payment is not made as agreed,Seller can remove said equipment/materials at Seller's expense.Any damage resulting behalf of above named company. from said removal shall not be the responsibility of Seller. r [-1REGULAR LlWARRANTY ® Dispatch C mo plet d �. ❑ SERVICE CONTRACT C IG E� DATE W TOTAL fr i HVAC CERTIFIED AIR CONTRACTORS, INC. SERVICE ORDER 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 • Fax (904) 389-4925 State Certification #CACO 08251 TYPE UNIT# TYPE UNIT# BILL TO MAKE MAKE TWI('o�Yc 00,40 MODEL SERIAL NUMBER NAMEILOC ION �1 STRFFT� S4J/l_�1�9 ENVIRONMENTAL CHECK LIST WORK COMPLETE YES❑ N0A WORK PERFORMED QTY. TYPE/DISPOSITION FOLLOW UP REPORT YES❑ NO❑ �I:/5 .�.-,,/c,+^�^c.^- /✓ ! �'✓� ^�'✓ ❑RECOVERED PHONE CONTACT ❑RECYCLED DISPATCH# TECF�IICI�fJ 1 AUTHORIZED BV ❑RECLAIMED Ju'(jTf fJ/``/ JOB# ❑RETURNED WORK TO BE PERFORMED ❑ CUSTOMER DISPOSAL P.O.# ❑DISMANTLED ❑CHANGED OUT:HFPLACED QTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PI�E-�RFF/O,�--Rb�MED REFRIGERANT R- LBS. . f I ------- ------------ 000, - , mac.•-ti_ clt - -. , , , , , TOTAL MATERIALS 3i �77— HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS TOTAL LABOR LIMITED WARRANTY: All materials, parts and equipment are warranted by the manufacturers' or TOTAL SUMMARY TERMS suppliers'written warranty only. All labor performed Should either party employ an attorney to institute suit or demand arbitration to enforce any of TOTAL the provisions hereof,to protect its interest in any matter arising under this agreement,or to by the above named company is warranted for MATERIALS collect damages for the breach of this agreement or to recover on a surety bond given by a 30 days or as otherwise indicated in writing. The party under this agreement,the prevailing party shall be entitled to recover reasonable above named company makes no other warranties, TOTAL attorney's fees,costs,charges,expenses,and interest expended or incurred therein. LABOR express or implied, and its agents or technicians I have authority to order the work outlined above which has been satisfactorily completed.I agree that are not authorized to make any such warranties on Seller retains title to equipmenUmaterialsfurnisfred until final payment is made.If payment is not made as agreed,Seller can remove said equipment/materials at Seller's expense.Any damage resulting behalf of above named company from said removal shall not be the responsibility of Seller. L e 4c</711 10 0 ,. 30 E:1REGULAR El WARRANTY ?, Dispatched: omplete : /00 E:1 SERVICE CONTRACT Gyro � � .�..._.� DATE C lC1(iALrr2C�b1U TOTAL L HVAC CERTIFIED AIR CONTRACTORS, INC. SERVICE ORDER 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 • Fax (904) 389-4925 State Certification #CACO 08251 TYPE UNIT TYPE UNIT# BILL TO MAKE MAKE MODEL MODEL li SERIAL NUMBER SERIAL NUMBER NAM — 1r4 SNO 13 ENVIRONMENTAL CHECK LIST WORK COMPLETE YES_� NO�I CITY F.1. 322 33 WORK PERFORMED QTY. TYPE/DISPOSITION FOLLOW UP REPORT YES❑ NO❑ ❑RECOVERED PHONE CONTACT ❑RECYCLED DISPATCH# TECHNICIAN AUTHORIZED BY ❑RECLAIMED JOB# 't ❑RETURNED WORK TO BE PERFORMED CiUSTOIVIER i DISPOSAL P.O.# I DISMANTLED I CIIANGEDOUT/REPLACED QTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT R- LBS. �V Vc TOTAL MATERIALS HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS r TOTAL LABOR LIMITED WARRANTY: All materials, parts and equipment are warranted by the manufacturers' or TOTAL SUMMARY TERMS Should either party employ an attorney to institute suit or demand arbitration to enforce any of suppliers'written warranty only.All labor performed the provisions hereof,to protect its interest in any matter arising under this agreement,or to by the above named company is warranted for TOTAL MATERIALS collect damages for the breach of this agreement or to recover on a surety bond given by a 30 days or as otherwise indicated in writing. The — party under thi9 agreement,the prevailing party shall be entitled to recover reasonableTOTAL attorney's fees,costs,charges,expenses,and interest expended or incurred therein. above named Company makes no Other warranties, LABOR express or implied, and its agents or technicians I have authority to order the work outlined above which has been satisfactorily completed.I agree that are not authorized to make any such warranties on Seller retains title to equipment/materials furnished until final payment is made.If payment is not made as agreed,Seller can remove said equipment/materials at Seller's expense.Any damage resulting behalf of above named Company from said removal shall not be the responsibility of Seller. ❑ REGULAR ❑ WARRANTY I. the Completed: ❑ SERVICE CONTRACT � `kF CUSTOM�RE DATEDATE ( TOTAL l 1 f HVAC CERTIFIED AIR CONTRACTORS, INC. SERVICE ORDER 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 111 Fax (904) 389-4925 State Certification #CACO 08251 TYPE UNIT TYPE UNITN BILL TO _ _ MAKE MAKE MODEL MODEL SERIAL NUMBER SERIAL NUMBER NAME/L Tf` , STREET FL+ - DATE ENVIRONMENTAL CHECK LIST WORK COMPLETE YES[3 NO ED CITY WORK PERFORMED OTY. TYPE/DISPOSITION FOLLOW UP REPORT YES❑ NO❑ PHONE CONTACT []RECOVERED - --- ❑RECYCLED DISPATCH# TECFJWCIAA/ AUTHORIZED BY El RECLAIMED BE 1 WORK TO BE PERFORMED J JOB# [I RETURNEDCUSTOMER ❑DISPOSAL P.O.# F1 DISMANTLED - !CHANGED OUT/REPLACED 1 QTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT R- LBS I 00, ; n , , , , - - �-� ci„__ , , ..ize , , , TOTAL MATERIALS j 1 HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS TOTAL LABOR LIMITED WARRANTY: All materials, parts and equipment are warranted by the manufacturers' or TOTAL SUMMARY TERMS Should either party employ an attorney to institute suit or demand arbitration to enforce any of suppliers' written warranty only. All labor performed the provisions hereof,to protect its interest in any matter arising under this agreement,or to by the above named company is warranted for TOTAL collect damages for the breach of this agreement or to recover on a surety bond given by a 30 days or as otherwise indicated in writing. The MATERIALS party under this agreement,the prevailing party shall be entitled to recover reasonable above named company makes no other warranties, TOTAL attorney's fees,costs,charges,expenses,and interest expended or incurred therein. LABOR I express or implied, and its agents or technicians f I have authority to older the work outlined above which has been satisfactorily completed.I agree that Seller retains title to equipment/materials furnished until final payment is made.If payment is not made are not authorized to make any such warranties on i as agreed,Seller can remove Said equipment/materials at Seller's expense.Any damage resulting behalf of above named company. 1, i from said removal shall not be the responsibility of Seller. ❑ REGULAR ❑ WARRANTY i D' patcft@d: O6 Compl d: � ❑ SERVICE CONTRACT CUSTOMER SIG RE s � DATE TOTAL I HVAC CERTIFIED AIR CONTRACTORS, INC. SERVICE ORDER 4505 Marquette Avenue JACKSONVILLE, FLORIDA 32210 (904) 389-7950 • Fax (904) 389-4925 State Certification #CACO 08251 TYPE UNIT# TYPE UNIT* BILL TO __. -_. ,..-_. MAKE MAKE MODEL MODEL •/y�r.� //�J L ,, �f/�J SERIAL NUMBEfl SERIAL NUMBER i NAME/LOCA�".`„"s'�+' I' STREET�©p DA, r ENVIRONMENTAL CHECK LIST WORK COMPLETE YES I�, NO❑ CITY /f 2 Z_3_3 WORK PERFORMED QTY. TYPE/DISPOSITION FOLLOW UP REPORT .YES❑ NO❑ PHONE CONTACT ❑RECOVERED ---------------- -----------. ❑RECYCLED DISPATCH# TECHNICIAN AUTHORIZED BY 71 RECLAIMED ,JOB# - WORK TO BE PERFORMED ❑RETURNED --- --"-- ------------------.-.-.-- l _ ❑DISPOSAL CUSTOMER P.O.# ❑DISMANTLED CHANGED OUT/REPLACED QTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED Ak HLF RIGERANT R- LBS70 . - � �` �• a �7 , , , , , , TOTAL MATERIALS J II-IRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS TOTAL LABOR LIMITED WARRANTY: All materials, parts and TERMS equipment are warranted by the manufacturers'or TOTAL SUMMARY Should either party employ an attorney to institute suit or demand arbitration to enforce any of suppliers'Written warranty only. All labor performed the provisions hereof,to protect its interest in any matter arising under this agreement,or to by the above named company is warranted for TOTAL collect damages for the breach of this agreement or to recover on a surety bond given by a 30 days or as otherwise indicated in writing. The MATERIALS party under this agreement,the prevailing party shall be entitled to recover reasonable TOTAL attorney's fees,costs,charges,expenses,and interest expended or incurred therein. above named Company makes n0 Other warranties, LABOR express or implied, and its agents or technicians I have authority to order the work outlined above which has been satisfactorily completed.I agree that Seller retains title to equipment/materials furnished until final payment is made.If payment is not made are not authorized to make any such warranties on as agreed,Seller can remove said equipment/materials at Seller's expense.Any damage resulting behalf of above named company. from said removal shall not be the responsibility of Seller. ❑ REGULAR ❑ WARRANTY Dised: r Comp ed, ❑ SERVICE CONTRACT �1tCUSTOM NATURE i DATE TOTAL ' CERTIFIED AIR CONTRACTORS, INHVAC C: R E I VIED D 4505 Marquette Avenue CITY OF ATLANTIC nEACH SERVICE ORDER JACKSONVILLE, FLORIDA 32210 g�n ^ ter ;` N' (904) 389-7950 • Fax (904) 389-4925 AUG p g 2005 State Certification #CACO 08251Qrtt UNIT - TYPE # BILL TO ..._ ., . . ..---_-.-- ___-__ . „. ..._`! , /yTf ,. f ! , MAKE MAKE �, e— �,ajLe MODEL MODEL 7G� O SCK' / vl�i SERIAL N�UyMBEFj ,� SERIA NUMBER NAME'LOCATION ".vt.`,(`�(�yL� 3 /I r / [f STREET DATE -�j ENVIRONMENTAL CHECK LIST WORK COMPLETE YES❑ NO❑ CITU 1 WORK PERFORMED QTY. TYPE/DISPOSITION �j f� _ FOLLOW UP REPORT YES❑ NO❑ PHONE CONTACT D RECOVERED ,__.-___.._________ I D RECYCLED DISPATCH#/ ��. 7ECHy1lA` /� AUTHORIZED BY D RECLAIMED i t f ' st JOB# WORK TO BE PERFORMED D RETURNED f� -.-- --- ......_.-.___._ [I DISPOSAL CUSTOMER P.O.# --- _---- D DISMANTLED i R.CHANGED OUT/REPLACED QTY. MATERIALS&SERVICES UNIT PRICE AMOUNT DESCRIPTION OF WORK PERFORMED REFRIGERANT R- X I_BS. - - lfwv rjl.� ui��7 lG7 G'yt Gtt/ 1 C!C i , a..al.—___ , I _ �. _. -------F--...�r _. --y- -_. i......-a7...;!�.._ ...t._ /!-..r-,C.I,.• �. ,__.__JC!r�'Sl..._L__ _....,_. ... ;/'.../t'�,�.,.,. �/_Gf^KI 1 3. 6R&I � TOTAL MATERIALS HRS. TECHNICIAN RATE AMOUNT RECOMMENDATIONS i TOTAL LABOR LIMITED WARRANTY: All materials, parts and TERMS equipment are warranted by the manufacturers' or TOTAL SUMMARY Should either party employ an/attorneinstitute suit or demand arbitration to enforce any of suppliers'written warranty only.All labor performed TOTAL the provisions hereof,to protest in any matter arising under this agreement,or to by the above named Company is warranted for MATERIALS collect damages for the breacreement or to recover on a surety bond given by a 30 days or as otherwise indicated in writing. Theparty under this agreement, ing party shall be entitled to recover reasonable above named company makes no other warranties, TOTALattorney's fees,costs,charges, ,and interest expended or incurred therein. express or implied, and its agents or technicians LABOR I have authority to order the wofk outlined above which has been satisfactorily completed.I agree that Seller retains title to equipmet4t/materials furnished until final payment is made.If payment is not made are not authorized to make any such warranties on as agreed,Seller can remove said equipment/materials at Seller's expense.Any damage resulting behalf of above named company from said removal shall not be the responsibility of Seller. rr/ if� �J J_ ❑ REGULAR ❑ WARRANTY D' etched:_Completed: _�� ❑ SERVICE CONTRACT CUSTOMER SIGNATURE DATE Ed�U/ TOTAL Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 p, 1 Cert ifie d-,qir Contractors, Inc. 4506 Marquette Avenue Jacksonville, Florida 32210 Phone: (904) 389-7950 Fax: (904) 389-4925 2 (� DATE: � PAGES: ��zx �Y�zns�zsszon TO: .004 FROM: 6� FAX: FAX: (904) 389-4925 PHONE: /,� PHONE: (904) 389-7950 RE- 49-1q;e ❑ URGENT ❑ FCR REVIEW ❑ PLEASE REPLY ❑ PLEASE COMMENT COMMENTS: N Z L-0c J JAN A P;�� TLANTICEACN Auchori:: FEB N0005 Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 p. 2 JAN 26 2005 11:28 FR CARRIER FLORIDA 9043631548 TO 3894925 P.02i02 Product Data: 5,ronz-Lmow,.,s IMPROVED: Dusky Coil Coat - Dip PROWL r a DIESCBIPTI Bronz-Glow's Husky Coll Coat,new dip formulation Jr.a tougher,more abrasion resistant coating with superior adhesion.Coll Cont won't rmck,chip or flake.Coll Cost Is dip applied only at Bronz-Glow Licensed In-house coating facilities.Prior to casting we employ a multistep spray washer surface cleaning and conditioning process to achieve a dean oil hee surface and apply an Impalpable chemically bonded coating treatment for secondary corrosion resistance and Improved adhesion. Husky Coil Coni protects fin tube and coaxial coils from harsh coastal and Industrial environments.Coll Cost with its elasticity expands and contracts at the same rate as ft base alloys It is protecting.Its full pH range protection quallbec guard against corrosive attack caused by harsh atmospheric environments.Husky Call Cost has negligible effect on heat transfer and If required.can be easily repaired in the field.Husky Coil Coat,because of Its unique properties,ensures the best overall corrasion protection In the market. During the cleaning and coating process the Coll Is never subjected to temperatures above 200 F.This protects braze and solder)olnts from heat stress which can occur during high temperature thermoset curing.Bronz-Glow Coil Coat Dip Process Guarantees 100%Covmaga. PRQQUCT APPLICANIONI: Coll Coat protects cora In harsh abrasive and corrosive atmospheres of salt air,hydrogen sulfide,hydrochloric acid,ammonia and chlorine among many others. Use to protect equipment placed In sugar refineries,coastal locations, petroleum refineries, chemical and phamwoeutical plants, coal and copper mines,paper mills, steel molls,waste water treatment facilities,tunnel exhaust systems,veterinary facilities,mushroom plants, swimming pool atmospheres,saw mills,ship board systems,hotels, motels, hospitals, restaurants, convention centers, shopping malls, airports, lbwA fuel generating stations and many other severe corrosive environments. HUSKY COIL COAT CHARACT RIt3TIC5: Elongation 290% Operating Temperature Range(Dry) -50 to+250 Dag.F. pH Range Protection 1.0-14.0 U.V.inhibitor In Film Coat 10 Year Florida sun Adhesion Properties Superior Abrasion Resistance Sup*rlor Heat Transfer Degradation NagNytble Ozone Depleter No PROJEt TS AGAINST CORROSIVE 6116"FROM: Salt Air Sulfuric Acid Fumes Tannic Acid Chlorine Salt Water Citric Acid Ammonia Methane Gas Acid Rain H25 Fumes Chlorides HCL Fumes Nitric Acid HF Acid Sulfuric Acid Uric f cidf Urea(excralions or urine from dogs,cats,birds&most Insects).Protects against other corrosive atmospheres. EFFECT ON HEAT TRANSFER DEGRADATION: Test showed no adverse effect(less than 11%) GAS CHROMATOGRAPHY TEST(FID):Test show no hazardous or toxic gases released after wring SALT SPRAY TEST: Passed 6.000 hours.ASTMB117.85(OEM Test) APPLICATION METHOD: Dip Tank Process.Coq Coat Is only applied at Bronz-Glow In-house coating fackbties. Brom-Glow® r /aA,/05- A ut sign lure CtYC -� JAN 26 2005 C.C. BORDEN _ONSTRUCTION,INC. * TOTAL PAGE.02 ** t k - Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 P. 1 Certifies -q, it Con.tractOYS, Inc_ 4505 Marquette Avenue Jackscnville, Florida 32210 Phone: (904) 389-7950 Fax: (904) 389-4925 DATE: _ PAGES: f�z,� ?��zns�zisszon TO: 1461 if i- FROM: /Oi S, llt/ /Sc j,,j FAX: FAX: (904) 389-4925 PHONE: PHONE: (904) 389-7950 RE: /77"/� LT �i4L� CC: ❑ URGENT ❑ FCR REMEW ❑ PLEASE REPLY ❑ PLEASE COMMENT COMMENTS: JAN 6 20� 01V TBO R O V E I) R FLANTIC BEACH fJrLD�I�IG OFFICE Authorized Reid ' 2005 Signature WC Rep--- Jan 26 05 10: 55a CERTIFIED AIR CONTRS INC 904-389-4925 p, 2 JAN 26 2005 11:28 FR CARRIER FLORIDA 9043631548 TO 3694925 P.02/02 Product Data: 15rona-wilow.s IMPROVED: Dusky Coil Coat - Dip PRODUCT'LXSo_BtMN-, Bronz-Glow's Husky Coll Coat,new dip formulation la a tougher,more abrasion resistant coating with superior adhesion.Coll Font won't crock,chip or flake.Coll Coat Is dip applied only at Bronz-Glow Licensed In-house costing fadlttles.Prior to coating we employ a multistep spray washer surface cleaning and conditioning process to achieve a dean oil free surface and apply an Impalpable chemically bonded coating treatment for secondary corrosion resistance and Improved adhesion. Husky Coll Coat protects fun tube and ooaxlal coils from harsh coastal and Industrial environments.Coll Cost with Its alaetidty expends _ and contracts at the same rate as the base alloys It Is protecting.Its full pH range protection qualifier.guard against corrosive attack caused by harsh atmospheric environments.Husky Coll Cost hem negligible effect on heat transfer and If required,can be easily repaired in the Reid.Husky Coil Coat,because of Its unique properties,ensures the best overall corrosion protection in the mrarlcot. Outing the cleaning and coating process the coil Is never subjected to temperatures above 200 F.This protects brims and solder)olnts from heat stress which can occur during high temperature thermoset curing.Brom-Glow Cod Coat Dip Process Guamn%es 100%Coverage. PBQQ iCT APPLICATION§: Coll Coat protects coils In harsh abraslve and corrosive atmospheres of salt air,hydrogen sulfide,hydrochloric acid,ammonia and chlorine among many others.Use to protect equipment placed In sugar refineries,coastal locations, petroleum refineries, chemical and pharmaceutical plants, coal and Copper minas, paper mills,steel mills, waste water treatment fadibes, tunnel exhaust systems,veterinary facilities,mushroom planta, swimming pool atmospheres,saw mills,ship board systems,hotels, motels, hospitals, restaurants, convention centers, shopping malls, airports, fo6sN fuel generating stations and many other severs corrosive environments. HUSKY COIL COAT CHAfRACTERI§TICS: Elongation 250% Operating Temperature Range(Dry) -50 to 4 250 Dag.F. pH Range Protection 1.0-14.0 LIM.Inhibitor In Film Coat 10 Year Florida Sun Adhesion Properties Superior Abrasion Resistance Superior Heat Transfer Degradation Negligible Ozone Deplater No PF&TECJS AGAINST CORROSNE ATTACK FROM: Salt Air Sulfuric Acid Fumes Tannic Acid Chloride Salt Water Citric Acid Ammonla Methane Gas Acid Rain H2S Furn" Chlorides HCL Fumes Nitric Acid HF Acid Sulfuric Acid Uric AcidlUrsa(dueretions or urine from dogs,cats,birds&most insects).Prolects against other oorToslvo atmospheres. EFFECT ON HEAT TRANSFER DEGRADATION: Test showed no adverse effed(less than 1%) GAS CHROMATOOF APHY TEST(FID):Test show no hazardous or toxic gases released after curing SALT SPRAY TEST: Passed 6.000 hours,ASTM8117.85(OEM Test) APPLICATION METHOD: Dip Tank Process.Coll Coat Is only applied at Brom-low in-house coating fecdities. Bronx-Glow® Authori d Revie='�— Signet a CQC Rep_._ - �(j� r. �. 1_ V ED JAN 2 6 2005 L.C. BORDEN "�;ONSTRUCTION, INC. ** TOTAL PAGE.02 ** I Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 p, 1 Cert ifie d-,qir Contractors, Inc. 4505 Marquette Avenue Jacksonville, Florida 32210 Phone: (904) 389-7950 Fax: (904) 389-4925 DATE: � � PAGES: JL ��zr 7��z�s�zsszon TO: '04 16 X--j FROM: 5 �/L rSuE�1 FAX. FAX: (904) 389-4925 PHONE: PHONE: (904) 389-7950 RE: j�-�tiZZ �� ,46� CC: ❑ URGENT ❑ FCR Rmne'x ❑ PLEASE REPLY ❑ PLEASE COMMENT COMMENTS: !1 12 F2 �� r CIi1! OF ATLANTIC E 1' v wl l sJ this slat:- JA N to�'� �> 6 ?®O5 NSTR j C'7'iO IV for N jNC Authorized Rrveevvur��—t..�._�..m.... Si Wture coc Rp. way Jan 26 05 10: 55a CERTIFIED AIR CONTRS INC 904-389-4925 p. 2 JAN 26 2005 11:28 FR CARRIER FLORIDA 9043631548 TO 3894925 P.02/02 rrioduct Data: isronz-Laiow7s IMPROVED: Dusky Coil Coat - Dip PSODUC T Lt:t3CHl Sronz-Glovers Husky Coll Cast,new dip formulation Is a tougher,more abrasion resistant coating with superior adhesion.Coll Cent won't crack,chip or Oaks.Coil Cost Is dip applied only at Bronz-Glow Licensed In-Muse coating fadltiles.Prior to coating we employ a multistep spray washer surface cleaning and conditioning process to achieve a dean oil free surface and apply an impalpable chemically bonded coating treatment for secondary corrosion resistance and improved adhesion. Husky Coil Cosi protects fin tube and ooaAal calls from harsh coastal and Industrial environments. Coll Cost with Its elasticity expends ..and coma at the same rate as the base alloys N Is protoong.Its full pH range protection qualities:guard against corrosive attack caused by harsh atmospheric environments.Husky Coll Cost has negligible effect on heat transfer and If required,can be easily repaired in the field.Husky Coil Coat,because of Its unique properties,ensures the beet ov"I corrosion protection in the mcarkot. During the cleaning and coating process the toll Is never subjected to temperatures above 200 F.This protects braze and solder)olnts from heat stress which can occur during high temperature thermoset curing,Brora-Glow Coit Coat Dip Process Guarantees 100%Coverage. PRODUCT APPLICAT10N8: Coil Coat protacts tolls In harsh abrasive and corrosive atmospheres of salt air,hydrogen sulfide,hydrochloric acid,ammonia and chiorine among many others.Use to protect equipment placed in sugar refineries,coastal locations, petroleum refineries, chemical and pharmaceutical plants, coal and copper mines,paper milts, a"rnills,waste water treatment facilities,tunnel exhsust systems,veterinary facilities,mushroom plants, swimming pool atmospheres,saw mills,ship board systems,hotels, motels, hospitals, restaurants, convention centers, shopping malls, alrports, fossil fuel generating stations and many other severe corrosive environments. HUSKY COIL COAT CHARACTERI8TIC5: Elongation 250% Operating Temperature Range(Dry) -50 t0 4 250 Deg.F. pH Range Protection 1.0-14.0 U.V.Inhibitor In Film Coat 10 Year Florida Sun Adhesion Properties Superior Abrasion Resistance Superior Heat Transfer Degradation Negligible Ozone Depleter No P-RQTE�j$AGAINST CORROSIVE 611MK FROM: Salt Air Sulfuric Acid Fumes Tannic Acid Chicrfne Salt Water Citric Acid Arrmtonia Methane Gas Acid Rein H26 Fumes Chlorides HCL Fumes Nitric Acid HF Acid Sulfuric Acid Uric Arid/Ursa(excreiians or urine from dogs,cats,birds&most Insects).Protects against other corrosive atmospheres. EFFECT ON kEAT TRANSFER DEGRADATION: Test showed no adverse affect(less than 1%) GAS CHROMATOGRAPHY TEST(FIB):Test show no hazardous or toxic gases released atter wring SALT SPRAY TEST: Passed 6.000 hours,ASTMB117.85(OEM Test) APPLICATION METHOD: Dip Tank Process,Coil Cost is only spoiled at Bronx-Glow In-Muse coating facilities. Bronx-Glow® ED JAN 2 6 2005 I C-'.C. BORDEN 'ONSTRU(MON,INC. r * TOTAL PAGE.02 ** F l 3 i Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 p, 1 C2Yt fie d-qir Contractors, Inc- 4505 Marquette Avenue Jacksonville, Florida 32290 Phone. (904) 389-7950 Fax: (904) 389-4925 DATE: A PAGES: �GZ��" 7YGZ�'LS�LZSs~�O12 TO: .� �e-L �� i-/�-� FROM: FAX: FAX: (904) 389-4925 PHONE: PHONE: (904) 389-7950 RE: �77/� �l /4//CC: Q URGENT ❑ FCR REWE'Ar ❑PLEASE REPLY ❑ PLEASE COMMENT COMMENTS: CITY OF ATLANTIC ,EiiCH BUILDING OFFICE i.1,u r� •� �nnG pvl;o T N T��1.ANTIC BEACH ��1ySTRU�t? �I:otNca OFFICR � 7, wo 3 2005 Authoi Signature Cil'- Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 p. 2 JAN 26 2005 11 28 FR CARRIER FLORIDA 9043631548 TO 3894925 P.02/02 Product Data: brongmuiow's IMPROVED: Husky Coll Coat - Dip �j'ri::L:�P c`4.I�1t7611�L`17GLi Sronz-Glows Husky Coll Coat,new dip formulation Is a tougher,more abrasion resistant coating with superior adhesion.Coll Coot umn,'t knack,chip or flake.Coll Cost Is dip applied only at Bronz-Glow Licensed In-house coating facilities.Prior to coating we employ a multistep spray washer surface cleaning and conditioning process to achieve a dean oil hes surface and apply an Impalpable chemically bonded coating treatment for secondary corrosion resistance and improved adhesion. Husky Coll Coat protects fun tube and coaxial colla from harsh cnaslal and Industrial environments.Coll Coat with its elasticity expands and contracts at the same rate as the base alloys It Is protecting.Its full pH range proladion qualities guard against corrosive attack Caused by harsh atmospheric environments.Husky Coll Coat ham negligible effect on heat transfer and If required,can be easily repaired in the field.Husky Coil Coat,because of Its unique properties,ensures the beat overall corrnslon protection in the morkot. During the cleaning and coating process the toll is never subjected to temperatures above 200 F.This protects blaze and solder)olnts from heat stress which can occur during high temperature thermoset curing:Bron-Glow Coll Coat Dip Process Guarantees 100%Coverage. PRQD iCT APPLICATIQN8: Coll Coat protects tolls In harsh abrasive and corroslvo atmospheres of suit air,hydrogen sulfide,hydrochloric acid,ammonia and chlorine among many others.Use to protect equipment placed In sugar refineries,coastal locations, petroleum refineries, chemical and pharmaceutical plants, coal and copper mines,paper mills,steel mills,waste water treatment facilities, tunnel exhaust systems,veterinary facilities,mushroom planta,swimming pool atmospheres,saw mills,ship board systems,hotels, motels, hospitals, restaurants, convention centers, shopping malls, airports, fossil fuel generating stations and many other severe corrosive environments. KUB COIL COAT CHARACTERISTICS: Elongation 250% Operating Temperature Range(Dry) -50 to+250 Dag.F. pH Range Protection 1.044.0 U.V.Inhibitor In Film Coat 10 Year Florida Sun Adhesion Properties Superior Abraalon Resistance Superior Heat Transfer Degradation Negligible Ozone Deplater No PROTEGIA AGAINST CORROSIVE 611A2Ir FROM: Salt Air Sulfuric Acid Fumes Tannic Acid ChioW* Salt Water Chdc Acid Ammonia Methane Goa Acid Rain H2S Fumes Chlorides HCI-Fumes Nitric Acid HF Add Sulfuric Acid uric AeidiUrna(e=reiions or urine from dogs,cats,birds&most insects).Protects against other w i Ive atmospheres. EFFECT ON HEAT TRANSFER DEGRADATION: Test showed no adverse effect!(less than 1%) GAS CHROMATOGRAPHY TEST(FID):Test show no hazardous or talc gases released after curing SALT SPRAY TEST: Passed 6.000 hours ASTM8117.85(OEM Test) APPLICATION METHOD: Dip Tank Process.Coll Cost to only applied at Bronz-Glow In-house coating feellWas. 71 Bro=-Glow® .IVED JAN 2 6 zoos S;Ivawne v;5 :.c:. BORDEN ''INSTRUCTION,INC. *� TOTAL PAGE.02 ** I i Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-389-4925 P. 1 Certified-qir Contractors, Inc- 4505 Marquette Avenue Jackscnville, Florida 32210 Phone: (904) 389-7950 Fax: (904) 389-14925 vs DATE: � � PAGES: �zr ?J��zszzsszon TO: "04L FROM: b—�/Scj j g6 094J C,-J FAX: .FAX: (90A) 389-4925 PHONE: PHONE: (904) 389-7950 RE: ?/�— �1 to 46/ CC: ❑ URGENT ❑ FCR REVIEW ❑ PLEASE REPLY ❑ PLEASE COMMENT COMMENTS: JAN 2 6 2005 �'yt OV `4 YED f/J � '�tC BEACH VcE rpr° FEB 0 3 2005 Jan 26 05 10: 55a CERTIFIED AIR CONTRS INC 904-389-4925 p. 2 JAN 26 2005 11:28 FR CARRIER FLORIDA 9043631548 TO 3994925 P.02i02 Product Data: itronzasuiows IMPROVED: Dusky Coit Coat - Dip Ems-cT--.E$Q3MN: eronz-Glows Husky Coll Cost,new dip formulation Is a tougher,more abrasion resistant coebng with superior adhesion.Coil C!orrt won't crock,chip or Oaks.Coll Coat Is dip applied only at Bronz-Glow Licensed In-Imso coatino facllttles.Prior to coating we employ a multistep spray crasher surface cleaning and conditioning process to achieve a dean oil free surface and apply an Impalpable chemically bonded coating treatment for secondary corrasion resistance and Improved adhesion. Husky Coil Coat protects fun tube and coaxial calls from harsh coastal and Industrial environments. Coil Coat with its Blest olty expends ..and contracts at the same rate as the base alloys It is protecting.Its full pH range protection qualities guard against corrosive attack caused by harsh atmospheric environments.Husky Coll Coat ham negligible effect on heat transfer and If required,can be easily repaired in the field.Husky Coil Coat,because of Its unique properties,ensures the best overall corrosion protection in the merkot. During the cleaning and coating process the toll Is never subjected to temperatures above 200 F.This protects braze and solder)olnts from heat stress which can occur during high temperature thermoset curing.Bronz-Glow Coil Coat Dip Process Guarantees IW%Coverage. PRQQ iCT APPLIC TION8: Coil Coat protects tolls In harsh abrasive and corrosive atmospheres of salt air,hydrogen sulfide,hydrochloric acid,ammonia and chlorine among many others. Use to protect equipment placed In sugar refineries,coastal locations, petroleum refineries, chemkatt and pharmaceutical plants, coal and Copper mines,paper mills, steel mills, waste water treatment fads,tunnel erAnaust systems,veterinary facilities.mushroom plants, swimming pool atmospheres.saw mills,ship board systems,hotels, motals, hospitals, restaurants, convention centers, shopping malls, alrpurts, fossil fuel generating stations and many other severe corrosive environments. HUSKY COIL COAT CHARACTERI8TIC5: Elongation 290% Operating Temperature Range(Dry) -50 to i 250 Dog.F. pH Range Protection 1.0.14.0 U.V.Inhibitor In Film Coat 10 Year Florida Sun Adhesion Properties Superior Abrasion Resistance Sup*rlor Heat Transfer Degradation Negligible Ozone Depleter No PFtQjEGj$AGAINST CORROSIVE Ajy&!QK FROM: Salt Air Sulfuric Acid Fumes Tannic Acid Chlorine Salt Water Citric Aced Ammonla Methene Goa Acid ficin H26 Fumes Chlorides HCL f=umes Nitric Acid HF Arid Sulfuric Acid Uric Acid/Unba(excretions or urine from dogs,cats,binds&most Insects).Protects against other corrosive atmospheres. EFFECT ON HEAT TRANSFER DEGRADATION: Test showed no adverse effect(less than 1%) GAS CHROMATOGRAPHY TEST(FID):Test show no hazardous or tonic gases released after curing SALT SPRAY TEST: Passed 8.000 hours.ASTM8117.85(OEM Test) APPLICATION METHOD: Dip Tank Process.Coil Coat Is only applied at Bronx-Glow in-house coating facilities. Bronz-Glove I i I ? ECEIV`ED JAN 2 6 2005 Si nature CCS:11 _ C.C. BORDEN 'INSTRUCTION,INc,. ** TOTAL PAGE.02 ** Jan 26 05 10: 55a CERTIFIED AIR CONTRS INC 904-388-4925 P. 1 Certified-q, ir Contractors, Inc. 4505 Marquette Avenue Jacksonville, Florida 32210 Phone: (904) 389-7950 Fax: (904) 389-4925 DATE: PAGES: zLJ7Qzon TO: 14 e r 0j `z-/�-� FROM: 66 FAX: FAX: (904) 389-4925 PHONE: PHONE: (904) 389-7950 RE: r/� '�1 tAI411 CC: ❑ URGENT ❑ FOR RE%IE'N ❑ PLEASE REPLY ❑ PLEASE COMMENT COMMENTS: AN 9 A4 O V E 111 nyF ATLANDING oFFtc NCN oil�---� Jan 26 05 10: 55a CERTIFIED RIR CONTRS INC 904-3€39-4925 p• 2 JAN 26 2005 11:28 FR CARRIER FLORIDA 9043631548 TO 38949'5_ P.02i02 Product Data. bronz. ,,wow s IJAPItOVED: Husky Coil Coat - Dip PPt�31l:IT f3E$ c ION: Brom-C3iovls Husskyky CCN Coat new dip formulation is a tougher,more abntelan resistant coating with superior adhesion.Coll Cont won't cmr.k,chip or hake.Coil Coat Is dip applied only at Bronz-Glow Licensed in-housa coatlnp fadlMles.Prior to coating we employ a multistep spray washer surface cleaning and conditioning process to achieve a dean oil hes surface and aPPIY an Impalpable ehamically bonded coating treatment for secondary corrosion resistance and Improved adhesion. Husky Coil Coat protects fit tube and coatdsi coils ham harsh coastal and Industrial environments.Cofl Coen wllft ibt elasticity expands and contracts at the am*rate as the base alloys it is protecting.its full pH range protection qualities guard against Corrosive attack caused by harsh atmospheric environments.Husky Coil Cost has negligible effect on heat transfer arab V required.can be easily repaired in the fieM.Husky Cod Coat bec oSe of Its unique properties,ensures the best overall corrosion protection In the market.during the cleaning and costing process the coil is never subjected to temperatures above 200 F.This orotects bfsze and Bolder joints from heat stness which can occur during high temperature thermoset curing.'Brom-Glow CCR Coat DIP Process Guarantees iW%Coverage. PRODUCT APPLICATI4 Lric acid,ammonia Coll Coat prota U cogs In harsh abrasive and corrosive atmospheres of salt air,hydrogen sulfide,hydrochloric and chkxirm among many others.Use Io protect equipment placed In sugar refineries,coastal ioesti0nns.Petroleum refineries, chemical and pharmaceutical plants,coat and copper mines,paper mills,steel mills,waste water Irealment facilities.tunnel 64must systems,veterinary facilities.mushroom plants,swimming pool atmospheres.saw mills,ship board systems,hotels, motels, haspitala, restaurants,convention centers, shopping maga. airports. bssN fuel generating stedcra and many other severe comoalve environments. HUSKY COIL COAT CHARACTERISTICS: Elongedon 250'x. Operating Temperature Range(Dry) •50 to 4 250 Deg.F. pH Range Protection 1.0-14,0 U.V.inhibitor in Film Coat 10 Year Florida Sun Adhesion Properties Superior Abrasion Resistance Superior Had Transfer Degradation Negtigtble Ozone 0e9101ter Nc pgo_yEal AGAINST CORROSIVE&UMK FROM: Salt Air Sulfuric Acid Fumes Tannic Acid Chtortna Salt Water Citric Acid Arnmonle Methane Gsa Acid Rain H26 Fumss Chlorides HCL f=umes Nitric Acid HF Add Sulfuric Acid Uric AcidiUrsa(excretions or urine from doge,cats,birds&most Insects).Prolects against other oon Ive atmospheres. EFFECT ON,WEAT TRANSFER DEGRADATION: Test showed no adverse affect(less than 1%) GAS CHROMATOGRAPHY TEST(FID):Test show no hazardous or tads gases released after curing SALT SPRAY TEST: Passed 8.000 hours.ASTMB117.85(OEM Test) APPLICATION METHOD: Dip Tank Pnaoess.Coll Coat is only applied a1 Bronz-aow in-house coating facilities• Brant-Glows I VE-1640s .. SAN 2( 15 ,iia D EN t N `T'RU'C 1'10N, *� TDTAL PAGE.02 **