Loading...
885 SEMINOLE RD-ROOF NON-SHINGLE -i yL�rly`� CITY OF ATLANTIC BEACH 800 SEMINOLE ROAD ATLANTIC BEACH, FL 32233 INSPECTION PHONE LINE 247-5814 ROOF NON SHINGLE - MUST CALL BY 4PM FOR NEXT DAY INSPECTION: 247-5814 PERMIT INFORMATION: PERMIT NO: ROOF18-0035 Description: shingle & modified bitumen re-roof Estimated Value: 10500 Issue Date: 4/11/2018 Expiration Date: 10/8/2018 PROPERTY ADDRESS: Address: 885 SEMINOLE RD RE Number: 170026 0000 PROPERTY OWNER: Name: HENRY PLANT OCBORNE Address: 1632 BEACH AVE ATLANTIC BEACH, FL 32233 GENERAL CONTRACTOR INFORMATION: Name: Address: Phone: Name: HAMMER TIME ROOFING Address: 13465 SOLEDAD CT DR JACKSONVILLE, FL 32204 Phone: PERMIT INFORMATION: Please see attached conditions of approval. WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOU PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT. NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property that may be found in the public records of this county, and there may be additional permits required from other governmental entities such as water management districts, state agencies, or federal agencies. * A notice of Commencement is only required for work exceeding an estimated value of $2,500. For HVAC work, a Notice of Commencement is only required when HVAC work exceeds and estimated value of$7,500. r City of Atlantic Beach APPLICATION NUMBER f n� Building Department (To be assigned by the Building Department.) r 800 Seminole Road �Ov F LS o o Atlantic Beach, Florida 32233-5445 Phone(904)247-5826 • Fax(904)247-5845 I r E-mail: building-dept@coab.us Date routed: t City web-site: http://www.coab.us APPLICATION REVIEW AND TRACKING FORM Property Address: 0 C3 (��� F—1 - Department review required Yes No Building Applicant: fYl4-r�<< �_ —C���(�(,I anning &Zoning 1- (� Tree Administrator Project: S V`� (��`.��- 1(Y1©(�c. +1 �Q Public Works Public Utilities Q-- `U� Public Safety Fire Services Review fee $ Dept Signature Other Agency Review or Permit Required Review or Receipt Date of Permit Verified By Florida Dept.of Environmental Protection Florida Dept. of Transportation St. Johns River Water Management District Army Corps of Engineers Division of Hotels and Restaurants Division of Alcoholic Beverages and Tobacco Other: APPLICATION STATUS _ Reviewing Department First Review: ❑Approved. Denied. ❑Not applicable (Circle one.) Comments: BUILDING PLANNING &ZONING Reviewed by: Date: TREE ADMIN. Second Review: A roved as revised. pp ❑Denied. ❑Not applicable PUBLIC WORKS Comments: PUBLIC UTILITIES PUBLIC SAFETY Reviewed by: Date: V 11-2 10p 41 FIRE SERVICES Third Review: ❑Approved as revised. ❑Denied. []Not applicable Comments: Reviewed by: Date: Revised 05/1912017 CITY OF ATLANTIC BEACH 800 SEMINOLE ROAD j <.0 ATLANTIC BEACH, FL 32233 (904) 247-5800 �4`J131 fir`' BUILDING REVIEW COMMENTS Date: 3/29/2018 Permit#: ROOF18-0035 Site Address: 885 SEMINOLE RD Review Status: denied REM 170026 0000 Applicant: HAMMER TIME ROOFING Property Owner: HENRY PLANT OCBORNE Email: HAMMERTIMEROOF@GMAIL.COM Email: Phone: 9047169149 Phone: 9045341428 THIS REVIEW IS ONE OF MULTIPLE DEPARTMENT REVIEWS. Revisions may not be submitted until ALL departments have completed their respective reviews. Revisions submitted MUST respond to EACH department review. Submittals that respond to only one or a few correction items will not be accepted. Correction Comments: 1. PrQ`�ide the manufacturer's installation instruction for the site specific installation steps far_the Mod. Bitumen system to be installed. Only information pertinent to this job, highlighted, 2 copies Building Mike Jones Building Inspector/Plans Examiner City of Atlantic Beach 800 Seminole Road Atlantic Beach, FL 32233 904.247.5844 Email:mjones@coab.us jErnA i)4-e1 Resubmittal Notes: All revisions and changes shall clearly stand out from the rest of the drawing on the sheet as a revision by way of completely encircling the change with "clouding".The revision shall also be identified as to the sequence of revision by indicating a triangle with the revision sequence number within it and located adjacent to the cloud.The revision date and revision sequence number shall also be indicated in a conspicuous location in the title block for each sheet on which a revision for that sequence occurs. For projects still in the initial review stage and permit pending, all sheets with revisions shall be inserted into each set of drawings.The original sheets must be clearly marked "VOID" but are to be left CITY OF ATLANTIC BEACH 800 Seminole Road r Atlantic Beach,Florida 32233 �!0;ti9' REVISION REQUEST/CORRECTIONS TO PLAN REVIEW COMMENTS i Date �" aD� Revision to Issued Permit_ Corrections to Comments_ Permit# Project Address 995— S,M,nh1 e Q Contractor/Contact NameA �Ctvnrl c/ r F L `/ ��/�c�l 6 Phone l�`�( I f2 - �� Email C Description of Proposed Revision/Corrections: Permit Fee Du $ Yom- Additional Increase in Building Value $ Additional S.F. By signingRt rlV66 A n affirm the Revision is inclusive of the proposed changes. Tinted name) Signature of Contractor/Agent(Contractor must sign if increase in valuation) Date (Office Use Only) Approved Denied Not Applicable to Department Revision/Plan Review Comments Department Review Required: Euildinnning & Zoning Reviewed By Tree Administrator Public Works Public Utilities / -C)ci l Public Safety Date Fire Services BUILDING PERMIT APPLICATION MAR 2 8 2018 11 CITY OF ATLANTIC BEACH I C EIC 0 F 800 Seminole Road,Atlantic Beach FL 32233 Office: (904)247-5826 * Fax: (904)247-5845 Job Address:_,?85 Se/,1 ;,icqJe_ 3):a3"i Permit Number: '—00F ( j —Cc�S— Legal Description"_ 9 16-a S-2-.9 6 .4 Le,-Y4 i RE# I Valuation of Work(Replacement Cost)$ 10_5j-Cn Heated/Cooled SF Non-Heated/Cooled ■ Class of Work(Circle one): New Addition Alteration Repair Move Demo Pool Window/Door ■ Use of existing/proposed structure(s)(Circle one): Commercial <I!e7i den4ti ■ If an existing structure,is a fire sprinkler system installed?(Circle one): Yes No■ Submit a Tree Removal Permit Application if any trees are to be removed or Affidavit of No Tree Removal Describe in detail the type of work to be performed: P,-,ezor Florida Product App;ov'* 7'q- I AO d 3 , for multiple products use product approval form Property Owner Information Name: nsinril-'i e Address: City &14, &e� StateZY—' Zip_3Phone E-Mail Owner or Agent (If Agent,Power of Attorney or Agency Letter Required) WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTOE OF COMMENCEMENT. Contractor Information: Name ofCompany: Qualifying Agent: 4101,114 &1eYQLA-r IL Address: 13 y 4 Sol cd,,:,,d C� cityCLL,,' 11 c -State Zip ta .j Office Phone (9bq) 71f-- !5�j q Job Site/Contact Number CZ(-f I State Certificabon/Registration# Cce—^13 R 99P3 E-Mail rnoc Are,", Architect Name&Phone# V Engineer's Name&Phone# Worker's Compensation r Exempt7(a!u.rjer / Uase Employees / Expiralidfi 1JW 'All is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commen issuance of apermit and that all work will be performed to meet the standards of all 16ivs regulating cons ction in this jurisdict becomes null and void if work is not commenced within six months, or i construction o workis nded or ab ndoned a My� 9,'1, e Furnaces,Boilers,Heaters,Tanks a s (6)months at anytime after work is commenced. I understand separate permits must be secure r dric I Plumbs F:.4 ,Pools,Furna and Air Conditioners,eta X I of Property Owner: Signature of Contractor: ne Day of Before me thiDay of 0 I z 0 j,m-tw� blic: Notary Public: V (,j or" rtify that I have read and examined this application and know the same to be true and correct. All provisions of laws ina Ns governing this type of work will be complied with whether specified herein or not. The granting of a permit does n, presume to give authority to violate.or cancel the provisions of any other federal, state, or local law regulating construction or the performance of construction. Rev.3/14/16 NOTICE OF COMMENCEMENT OFFICE COPY �7 (PREPAPE IN DUFLIC.ATI E) Permit No. /ZoaPl��a�3S- Tax Folio No. 700, State of_, -7n_, c._ County of v, To whom it may concern; The undersigned hereby informs you that improvements will be made to certain real property,and in accordance with Section 713 of the Florida Statutes,the following information is stated in this NOTICE OF COMMENCEMENT. Legal description of property being improved/: IJ - �1 1 (0 - a S r? /J k-L 4 AC a 1c Address of property being improved: �� 'S,!,-., Pcj Ft 311-3 Ganeral description of improvements: Owner // Address J1 t— {ti L Owners interest in site of the improvement Fee Simple Titleholder(if other than owner) Name Address Contractor /�C 2.�+�ecTM a Address I`3'���5 _�t��� c� C'�_ Phone No.(§Qq W 6 Fax No. Surety(if any) Address amount of bond S Phone No_ Fax No. Name and address of any person making a loan for the construction of the improvements. Name Address Phone No. Fax No. Name of person within the State of Florida.other than himself,designated by owner upon:Thom notices or other documents may be served: Name Address Phone No. Fax No. In addition to himself,owner designates the following person m receive a copy of the Lienor's Notice as provided in Section 713.06(2)(b),Florida Statutes.(Fill in at Owner's option). Nam= Address Phone No. Fax No. Expiration date of Notice of Commencement(the expiration date is one(1)year from the date of recording unless a different date is specified): lk„» THIS SPACE FOR RECORDER'S USE ONLYSigned- oarcre e this of in the i County of L 31,$tale Of F!S�d= ' �p-rsonally appeared o rn +L/�✓i.i ( ' b �JlDn cL herein by >,<z<- JJ hirrsel herself and affi s thm at all stateents and declarations herein Doc#2018071753 OR BK 18329 Page 1102 I are trua and accurate z M,r.2z Number Pages:1 i Z��-, Recorded 03/28/2018 09:50 AM, / �CD z RONNIE FUSSELL CLERK CIRCUIT COURT DUVAL _3 yk COUNTY T C� T RECORDING $10.00 Notan:^rub!icat arca,Sta=of Countyof m« FAY commission expires: rQ Personally Kncvn or � � Roduc_d ldentinca8on i r- ' ,.mow CertainTeed 0 L1NT Tl F Application Handbook - Third Edition An educational program OFFICE COPY for professional roofing contractors A i E'er SAINT-GOBAIN Basic Application: Flintlastic SA Modified Bitumen Important Application Considerations • Do not attempt application if ice, snow, moisture or dew are present. Bonding substrates must be clean, dry and free of dust or other inhibitors of proper adhesion.Ambient temperature must be 50OF or above. • Store Flintlastic SA rolls indoors on pallets, protected from the elements. Rolls that are improperly stored or have been warehoused for prolonged periods of time may lose their tack. • Do not apply membrane that has been improperly stored, exposed to moisture, or has lost its tack. If the material isn't bonding, STOP the application! • Always remember to put safety first and follow all OSHA safety guidelines with any roofing installation. • Substrates must be free of dust, dirt, oil, debris and moisture. • Primer, if used, must be applied at the specified rate and must be allowed to thoroughly dry. • Work with manageable lengths of MidPly and Cap for the particular job. Where appropriate, cut rolls into 1/3-or 1/2-roll lengths and allow material to relax prior to installation. • In cooler weather, a hand-held hot air welding gun can be used to warm the sidelap areas and improve adhesion (prior to application of the FlintBond SBS Modified Bitumen Adhesive). • Use caution with the weighted roller at endlap areas. Don't squeeze out too much adhesive. • When applying MidPly(or PlyBase)directly to substrate, design adequate roof ventilation into the system through the use of roof relief vents. • Do not mix Flintlastic SA membranes with other types of roof membranes. Flintlastic SA membranes are specifically designed to be applied together. The permanent top film of the MidPly, PlyBase and NailBase cannot receive torching, hot asphalt or other non selfadhering application methods.The Flintlastic SA Cap(or SA Cap FR), PlyBase and MidPly cannot be applied to any surfaces other than as described herein. • Do not use cold adhesives with Flintlastic SA membranes other than for flashing details and cap sheet overlaps as described herein. • Refer to the CertainTeed Commercial Roof Systems Manual for complete requirements. • All plies of the assembly should be installed in one day. If blue film must be exposed for longer periods of time, cover with tarp or suitable alternate protection. 38 • When applying Flintlastic SA on slopes exceeding 1" in 12", membranes shall be back nailed.When applied parallel to the slope, Flintlastic SA shall be blind-nailed at end laps 2"in from top edge,6"o.c.through tin discs and to wood nailers. See General Requirements Section of the CertainTeed Commercial Roof Systems Manual for details. Deck Preparation CertainTeed recommends the use of Flintlastic SA NailBase base sheet in conjunction with all self-adhering membrane roof installations. Flintlastic SA NailBase can be mechanically attached to nailable substrates or applied using hot asphalt(non-nailable substrates). For non-nailable substrates where use of hot asphalt to adhere the base sheet may not be appropriate, Flintlastic SA MidPly or Flintlastic SA PlyBase may be used in lieu of Flintlastic SA NailBase on surfaces properly primed with FlintPrime" SA. However, note that without the use of a base sheet, the membrane may be difficult to later remove(if necessary)and certain UL and FM listings for the products may not apply. Prior to application of Flintlastic SA products, ensure roofs have positive drainage. Consult the local building official for minimum slope and drainage requirements. Application of Flintlastic SA NailBase Beginning at the low point of the roof, mechanically fasten Flintlastic SA ilBase o nailable deck using appropriate fasteners. Start with an appropriate roll width (1/3 or 1/2 roll) to accommodate offsetting of sidelaps of subsequent layers of MidPly and/or Cap sheet. Install '. so that no sidelaps are against the flow of water.A minimum fastening ddK� fib` pattern is every 9"on center on sidelaps and every 18"on center 9 in two staggered rows in the field 7 of the sheet. Prime non-nailable substrates such as concrete using FlintPrime SA polymer-based primer.Allow to A ;ZAa„ dry thoroughly, but not more than 4 hours to retain tack-enhancing properties.Apply SA NailBase using ASTM Type III or IV hot asphalt* at f. the rate of 25 lbs. per 100ft2(Spot mopping-15 lbs. per 100ft2)or self-adhere SA PlyBase(or MidPly). 39 Overlap base sheet sidelaps 2"and endlaps 4".Offset endlaps a minimum of 3'.Turn base sheet over fascia. Do not leave installed base exposed. Cover in the same day with Flintlastic SA MidPly and/or Flintlastic SA Cap (or SA Cap FR). Don't leave the installed Flintlastic SA NailBase exposed to the weather; cover with Flintlastic SA Cap the same day. Application of Flintlastic SA Mid Ply or PlyBase to insulate decks SA MidPly or PlyBase may be adhered directly to mechanically fastened FlintBoard ISO or adhered to FlintBoard ISO Cold. Before installing, sweep the surface of the insulation boards to remove any dust, dirt or sand particles that could interfere with adhesion. Start application at the low point of the roof. Install flush to roof edge. Design layout so that no sidelaps are against the flow of water. Application of Interply Note: Proceed to "Before Installing Flintlastic SA Cap(or SA Cap FR)" if installing a 2-ply system. Before installing Flintlastic SA MidPly(or PlyBase), sweep the underlying base sheet or primed surface to remove any dust,dirt or sand particles that could interfere with adhesion. Apply MidPly(or PlyBase)over installed Flintlastic SA NailBase or,for non-nailable decks such as concrete, properly primed substrates. Surface must be dry and free from dust or dirt. Start MidPly(or PlyBase)application at the low point of the roof with appropriate roll width to offset sidelaps 18"from sidelaps of base sheet. Install flush to roof edge if over base sheet, otherwise turn the MidPly(or PlyBase)over the fascia minimum 2"and secure. Design layout so that no sidelaps are against the flow of water. Cut rolls into manageable lengths. Fold the membrane back halfway lengthwise to remove the split release film. Press membrane securely into place, and repeat with the opposite half of the membrane. Use a heavy,weighted roller over 8 the entire surface of the Flintlastic SA MidPly(or PlyBase)membrane to secure the membrane.Work %' outwards to eliminate voids. 40 Overlap sidelaps of subsequent MidPly(or PlyBase)membrane lengths 2"and endlaps 6".Offset(stagger)endlaps minimum 3'. Cut endlaps at opposing diagonal corners at an angle approximately 5-1/2"long by the selvage dimension from the corners to minimize"T"-seams.Apply a bead or small trowel dab(quarter size)of FlintBond' SBS Modified Bitumen Adhesive,trowel or caulk grade, at the edge of the angled cut to avoid a capillary. Use of a hand-held hot air gun at the joint area prior to rolling the membrane will maximize adhesion. In areas prone to cold temperatures, snow and freeze-thaw cycles, it may be more effective to use the hot air gun to form joints, and to completely fill all mole holes with asphalt that has been slightly melted using the gun. It is recommended to apply a bead of FlintBond SBS Modified Bitumen Adhesive, caulk grade, at all MidPly (or PlyBase)side and endlaps to eliminate a capillary. Don't leave the installed Flintlastic SA MidPly(or PlyBase)exposed to the weather; cover with Flintlastic SA Cap the same day. Before Installing Flintlastic SA Cap (or SA Cap FR) mtgj If roof edge detail utilizes edge metal, proceed as follows. If MidPly has been applied, install minimum 26 gauge edge metal using appropriate fasteners, and set entirely in a uniform 1/8"A/4"thick troweling of FlintBond SBS Modified Bitumen Adhesive,trowel grade. Remove any oil from the metal surface using a vinegar and water solution. Prime the horizontal surface of the metal with FlintPrime SA and allow primer to dry. Apply a bead of caulk grade FlintBond adhesive to the edge of the metal where it meets the MidPly. Proceed with Flintlastic SA Cap(or SA Cap FR) installation. If MidPly is not specified: Over the Flintlastic SA NailBase, install a 9" wide strip of MidPly onto the field of the roof and flush to the roof edge, self-adhered. Install minimum 26 gauge edge metal using appropriate fasteners, set entirely in a uniform 1/8"-1/4"thick troweling of FlintBond SBS 41 Modified Bitumen Adhesive, trowel grade. Remove any oil from the metal surface using a vinegar and water solution. Prime the horizontal surface of the metal with FlintPrime or FlintPrime SA and allow primer to dry.Apply a bead of caulk grade FlintBond SBS Modified Bitumen Adhesive at the roof side edge of the metal where it meets the MidPly strip. Proceed with cap sheet installation. Similarly, complete your sheet metal flashing installation using cut MidPly flashing collars at all flashing details prior to flashing application. Seal edges of MidPly flashing collars with a bead of FlintBond. See "Typical Construction Details," starting on page 45 for examples. If MidPly has been installed as part of the system, set flanges in trowel grade FlintBond and properly fasten.All cap sheet flashings installed to transitions that overlap onto mineral surface must be set in a uniform troweling of FlintBond trowel grade adhesive. �w Application of Flintlastic SA Cap (or SA Cap FR) Before installing Flintlastic SA Cap(or SA Cap FR), sweep the surface of the installed SA NailBase(or PlyBase)or MidPly clean.To install Flintlastic SA Cap(or SA Cap FR), start at the low point of the roof with an appropriate roll width to offset sidelaps from the underlying membrane a minimum of 18".Work with manageable lengths for proper handling. a��= s* Position SA Cap(or SA Cap FR) with selvage edge release strip at high side of roof. Install in weather-lapped fashion, with no N1,' laps against the flow of water. 42 Once positioned, lift and fold back(lengthwise)the lower half of the membrane. Remove the split release film and press firmly into place. Then repeat with the other (high side of the roof) half of the membrane. Follow the same layout and split release film procedures as for MidPly(or PlyBase), but overlap0 ilw,'W' 11 sidelaps 3"and endlaps 6". Use "- a weighted roller over the entire surface of Flintlastic SA Cap(or SA Cap FR)to secure it in place and prevent voids, working outward from the center of the sheet. As subsequent membrane lengths are installed, remove the selvage edge release strip just prior to overlapping to keep the adhesive 'Q' area protected and clean. Cut endlaps at opposing diagonal corners at an angle approx. 3"by 5-1/2"from the corners to minimize T-seams. Use FlintBond SBS Modified Bitumen Adhesive,trowel grade, on the entire 6"width of each endlap prior to overlapping.Apply a uniform 1/8"-1/4"troweling of the FlintBond on the entire width of the endlaps to the underlying membrane. Install the overlapping sheet.Always apply FlintBond (extend beyond underlying lap minimum 1/4")on the entire width of any overlap when applying SA Cap(or SA Cap FR)over another mineral surface such as the SA Cap(or SA Cap FR)endlap. At all vertical and other flashing points, apply FlintBond SBS Modified Bitumen Adhesive, trowel grade, wherever there is an overlap onto mineral surfacing. Once the membrane has had a chance to bond, check all laps and joints for full adhesion. If the membrane can be lifted at any area it is not properly adhered. q;7 A seam probing tool can be helpful 1,01 to check for small voids at taps. 43 If necessary, use appropriate hand-held hot air welding tool and seam roller or an application of FlintBond to seal small unbonded areas if they exist. Included in this manual are a few common construction details. Please refer to CertainTeed's standard details or the NRCA for details not found within this manual. Important to note with all details, all metal must be primed and set in FlintBond Trowel Grade adhesive and all overlaps over mineral surfacing must utilize FlintBond Trowel Grade adhesive. The Proper T-Seam Detail • Before adhering Flintlastic SA MidPly or Cap(or SA Cap FR) endlaps, trim the underlying sheet's lower corner at the end of the roll. • Follow with the overlapping sheet, trimming the upper outside corner. • Corners should be trimmed on a diagonal angle 51/2" long from end of roll to outside edge. • Width of trim should be Apply Fling"888 M"Oed eituman Adheal""%V4 wad. equal in width to the to T"twl°-andtap W M kmkxff" tM andlep cut alae sidelap specified 1 (3"for Flintlastic SA Cap [or SA Cap FR] and 2" for Flintlastic SA MidPly [or PlyBase]). • Trimmed corners should be completely covered by application ' a Pow of succeeding courses. -' 'd~e «° s.�app�° • Note: If using Flintlastic SA MidPly(or PlyBase), h apply quarter-size dab of FlintBond at T-seam area. If using Flintlastic SA Cap(or SA Cap FR), the endlap should be completely set in trowel grade FlintBond along the entire 6" lap width. Rake Edge Detail ~A • Cut selvage area at an angle at all rake edges. ` • Apply a bead of FlintBond caulk along cut edge to eliminate mole holes. 44