Loading...
480 Aquatic Dr RES19-0374 Siding Repair =...±',-:":0--4-k-i-7,,,,, RESIDENTIAL PERMIT PERMIT NUMBER RES19-0374 CITY OF ATLANTIC BEACHISSUED: 12/30/2019 800 SEMINOLE ROADATLANTIC BEACH. FL 32233 EXPIRES: 6/27/2020 MUST CALL INSPECTION PHONE LINE (904) 247-5814 BY 4 PM FOR NEXT DAY INSPECTION. ALL WORK MUST CONFORM TO THE CURRENT 6TH EDITION (2017) OF THE FLORIDA BUILDING CODE, NEC, IPMC, AND CITY OF ATLANTIC BEACH CODE OF ORDINANCES . ALL CONDITIONS OF PERMIT APPLY, PLEASE READ CAREFULLY. NOTICE: In addition to the requirements of this permit,there may be additional restrictions applicable to this property that may be found in the public records of this county, and there may be additional permits required from other governmental entities such as water management districts, state agencies, or federal agencies. JOB ADDRESS: PERMIT TYPE: DESCRIPTION: VALUE OF WORK: 480 AQUATIC DR RESIDENTIAL ALTERATION SIDING REPAIR $5200.00 RESIDENTIAL TYPE OF REAL ESTATE ZONING: BUILDING USE SUBDIVISION: CONSTRUCTION: ' NUMBER: GROUP: 171818 5160 AQUATIC GARDENS COMPANY: ADDRESS: CITY: STATE: ZIP: BETTER HOME IMPROVEMENT 538 PARK AVE ORANGE PARK FL 32073 OWNER: ADDRESS: CITY: STATE: ZIP: MINGO EDWIN G 480 AQUATIC DR ATLANTIC BEACH FL 32233-3836 WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT. 'Roll off container company must be on City approved list . Container cannot be placed on City right-of-way. L - — 43 4 DESCRIPTION ACCOUNT QUANTITY PAID AMOUNT BUILDING PERMIT 455-0000-322-1000 0 $80.00 BUILDING PLAN CHECK 455-0000-322-1001 0 $40.00 STATE DBPR SURCHARGE 455-0000-208-0700 0 $2.00 STATE DCA SURCHARGE 455-0000-208-0600 0 $2.00 TOTAL: $124.00 Issued Date: 12/30/2019 1 of 2 ''''''� RESIDENTIAL PERMIT PERMIT NUMBER ,S r� �`, RES19-0374 CITY OF ATLANTIC BEACH 800 SEMINOLE ROAD ISSUED: 12/30/2019 '`'; �T V ATLANTIC BEACH. FL 32233 EXPIRES: 6/27/2020 Issued Date: 12/30/2019 2 of 2 (-:-.75LAI.1-,f, City of Atlantic Beach APPLICATION NUMBER 40ABuilding Department (To be assigned by the Building Department.) %1800 Seminole Road R _C l� - 03 7.4 �) Atlantic Beach, Florida 32233-5445 J I Phone(904)247-5826 • Fax(904)247-5845 11 Q -o;s r% E-mail: building-dept@coab.us Date routed: 1 ( C� City web-site: http://www.coab.us APPLICATION REVIEW AND TRACKING FORM Property Address: - Q O R I i 0 Department review required Y No 4 Building_ Applicant: `. &TrER- L 40n6 i m.Pres-DV Planning &Zoning Tree Administrator Project: S( 0 ( (\jY R L C'A ( 2_ Public Works 1 Public Utilities Public Safety _ Fire Services Review fee $ Dept Signature Other Agency Review or Permit Required Review or Receipt Date of Permit Verified By Florida Dept. of Environmental Protection Florida Dept. of Transportation St. Johns River Water Management District Army Corps of Engineers / `—� Division of Hotels and Restaurants f u ` Division of Alcoholic Beverages and Tobacco .4t` \/ Other: APPLICATION STATUS Reviewing Department First Review: Approved. Denied ❑Not applicable (Circle one.) Comments: BUILDIN '/� PLANNING &ZONING Reviewed by: /' i ' . Date: / - "c 3 -do/9' TREE ADMIN. Second Review: ❑Approved as revised. ❑Denie . ['Not applicable PUBLIC WORKS Comments: PUBLIC UTILITIES PUBLIC SAFETY Reviewed by: Date: FIRE SERVICES Third Review: I 'Approved as revised. ❑Denied. ❑Not applicable Comments: Reviewed by: Date: Revised 05/19/2017 sA"'`�}, Building Permit Application OFFICE COPY Updated 10/9/18 rzt 1 City of Atlantic Beach Building Department **ALL INFORMATION 800 Seminole Road, Atlantic Beach, FL 32233 HIGHLIGHTED IN GRAY �';t`�r IS REQUIRED. Phone: (904) 247-5826 Email: Building-Dept@coab.us Job Address: 480 4Qu hc_.b'I Vel Ati et rw,&adi. FL mit Number: R[.S t 9 — 0 3-7 4 Legal Description 3e)---11 11'"iS -261 E AQ(i{e(1 G 6ti—ez / s Gtr&-R6E# 13I818-61 Loo Valuation of Work(Replacement Cost)$ 6 i 2.00• 00 Heated/Cooled SF Non-Heated/Cooled • Class of Work: ❑New ❑Addition DAlteration 47'ftepair [Move ❑Demo DPool ❑Window/Door • Use of existing/proposed structure(s): ❑Commercial Vesidential • If an existing structure,is a fire sprinkler system installed?: ❑Yes o ,/ • Will tree(s)be removed in association with proposed proi)ect? DYes(must submit separate Tree Removal Permit) 14 Describe in detail the type of work to be performed: 8iclt ^L- tr Th�L4ng 4 ►e on 2X10 S- hrt j leve only to fror►t- oC and door a.n d Lem` 2t a.s we Ll fyo rv+ o4 t OA--}- s d-trii level Not' i its izt lt,n3 5c diA A5 -6 ba—kc—04' horvN.12-- Florida Product Approval# I-6 t q a . oZ for multiple products use product approval form Property Owner Information Name EAWi n A.br exuadace k. MMNGO Address 980/4 f4aiiC hri reAfiaMll'(1e41i A• 32233 City�cenNG /rr i�GLS State Zip 323 3 Phone q014-15-9—'7?�5' E-Mail a VY1 in:Cp(0J WW 9.-Pi/ CA r1,--1 Owner or Agent(If gen , Power of A-torney or Agency Letter Required) QN Contractor Information t Name of Company'F kk.t(4 Tn�►.)roy�vywxy l c.-., Qualifying Agent Kevin }-tu.,r Address5313 Pc.(� J4Ve, J-Ll S41 . Citybra rw, r►f-- State FL Zip 31.-09q t.A Office Phone 964 -a.-78-cBto Job Site Contact NumterOL(-a-'1s-08 L 0 State Certification/Registration# CISCO S t 14a E-Mail (Y1Q.tii 0�9 b1'1►�O p1^ r,l •LO '\ CC I J Z Architect Name&Phone# J (ldt __ij a_ 0 Engineer's Name&Phone# Lii0 f= Workers Compensation Insurer c- y- OR Exempt❑ Expiration Date I - I — 2-® [a F' Z CI - r,4,&I� (c& Application is hereby made to obtain a permit to do the work and installations as indicated.I certify that no work or installatiP KatC3 0 c commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all the laws regul ¢ CI construction in this jurisdiction. I understand that a separate permit must be secured for ELECTRICAL WORK,PLUMBING,SIG `- 0 2 QQ Q WELLS,POOLS, FURNACES, BOILERS, HEATERS,TANKS,and AIR CONDITIONERS,etc. NOTICE: In addition to the requirementOf tIas� co Z permit,there may be additional restrictions applicable to this property that may be found in the public records of this count Cl) Z there may be additional permits required from other governmental entities such as water management districts,state agent ,ac ri 1.-.LI federal agencies. OU51 11 A >, att m OWNER'S AFFIDAVIT: I certify that all the foregoing information is accurate and that all work will be done in compliance withl l I-- LU 5 0 UJ applicable laws regulating construction and zoning. LLa C.) N W CC W WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MA5 RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTE�IVD ¢ TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN >0 = ' NEY BE 0! RE -- REC•RDING O . R NOTICE OF COMMENCEMENT. .f� (Sign;1e of Owner or Agent) (Signature of Contractor) Signed and sworn to(or affirmed)before me this /8/day of Signed and sworn to(or affirmed)befor- 22- Nis / day of a , &O/7,by/�' r ii.' ,_ /.G.440,--,-O/9 , by .��v� .i / i f��� _ I Ar 4--- (5t i' Ignatur � �rLk/E PRAY VE PRAY " YP' '!A State of Florida-Notary Public =� e=_State of Florida-Notary Public 'i;) '�-�.,� ' _'• �" *_ Commission # GG 273341 Commission # GG 27334r �o` [ ]P onally Known OR �t.' My Commission Expires`(„?ersonally Known OR ;:o ,e[io ,. My Commission Expires November 01, 2022 November 01, 2022 Produced Identification ___ ) ,?roauced Identification Type of Identification: FA___ �"�' Type of Identification: HOoTIME Or `SCC NVEMIGEMEHT OFFICE COPY /� V (PREPARE IN DUPLICATE) Permit No. i/G �y 0 3 7 Tax Folio No. State of Florida County of OU.A./4.-1 To whom it may concern: The undersigned hereby informs you that improvements will be made to certain real property,and in accordance with Section 713 of the Florida Statutes,the following Information Is stated In this NOTICE OF COMMENCEMENT. Legal description of property being improved: 38--7 ) —2S -Zq f% fQu- —Tic c 47W JS Go 7' 8-6 Address of property being improved: 4'97 h .51-7G Acire,_/11-/oir17G cyz2 5 General description of improvements: (. 146 Owner A41.Ai o) `GA'w/f G. 21- (14,vt Address I O 4gij I7.(r t3- Irl/Qlt'j' -QpY- , 3'22 3') Owner's interest in site of the improvement Fee Simple Titleholder(if other than owner) Name Address Contractor Better Home Improvement Inc. Address 538 Park Avenue,Ste 1,Orange Park,FL 32073 Phone No.904-278-0810 Fax No.904-278-8211 Surety(if any) Address Amount of bond$ Phone No. Fax No. Name and address of any person making a loan for the construction of the improvements. Name Address Phone No. Fax No. Name of person within the State of Florida,other than himself or herself,designated by owner upon whom notices or other documents may be served: Name Address Phone No. Fax No. In addition to himself or herself,owner designates the following person to receive a copy of the Lienor's Notice as provided in Section 713.06(2)(b),Florida Statutes.(Fill in at Owner's option). Name Address Phone No. Fax No. Expiration date of Notice of Commencement(the expiration date is one(1)year from the date of recording unless a different date is specified): M a THIS SPACE FOR RECORDER'S USE ONLY OWNER 'N ao < - WN Signed' '/- 2.7ICC-/S-/f z c7 c, Before me this day of / in thex v, County of D val,State of Florida,'has personally apps ed / w c.�' 0) Doc#2019288416, OR BK 19041 Page 1446, , n, �1�i1 herein by w o.P E Number Pages: 1 himself/herself and affirms dint all statements and declarations herein ,, E Recorded 12218/2019 11:34 AM, are true and accurate ,- --- v)o v o' m RONNIE FUSSELL CLERK CIRCUIT COURT DUVAL E >.z2 COUNTYo RECORDING $10.00 �� � Notary f?ubiic at Large,State ofi"' 4, , county of J/—i'` •bo My commission expires: ,s`(i 'o= Personally Known / or ;o^ Produced identification �/�- � ,"„o` UI-HUE COPY )," PRODUCT APPROVAL INFORMATION SHEET FOR THE CITY OF ATLANTIC BEACH, FLORIDA (*REQUIRED) *Project Address: 480 Aquatic Drive Permit#: ,Q / 9— 0 3 7 if *Owner/Project Name: Edwin Mingo As required by Florida Statute 553.842 and Florida Administrative Code Rule 9B-72, please provide the information and product approval number(s)for the building components listed below as applicable to the building construction project for the permit number listed above. You should contact your product supplier if you do not know the product approval number for any of the applicable listed products. Information regarding statewide product approval may be obtained at:www.floridabuilding.org. Category/Subcategory Manufacturer Product Description Limitation of Use State# Local# A. EXTERIOR DOORS 1. Swinging 2. Sliding 3.Sectional 4. Garage Roll-Up 5.Automatic 6. Other B.WINDOWS 1. Single hung 2. Horizontal slider 3. Casement 4. Double hung 5. Fixed 6.Awning 7. Pass-through 8. Projected 9. Mullion 10.Wind breaker 11. Dual action 12. Other Page 1 of 4 Updated 10/17/18 OFFICE LUNY Category/Subcategory Manufacturer Product Description Limitation of Use State# Local# C.PANEL WALL. 1.Siding James Hardie Cementous Siding Material FL13192.2 2.Soffits 3. EIFS 4.Storefronts 5.Curtain walls 6.Wall louvers 7.Glass block 8. Membrane 9.Greenhouse 10.Synthetic stucco 11. Other D. ROOFING PRODUCTS 1.Asphalt shingles 2. Underlayments 3. Roofing fasteners 4. Nonstructural metal roof 5. Built-up roofing 6. Modified bitumen 7.Single ply roofing 8. Roofing tiles 9. Roofing insulation 10.Waterproofing 11.Wood shingles/shakes 12. Roofing slate 13. Liquid applied roofing 14. Cement-adhesive coats 15. Roof tile adhesive 16.Spray applied polyurethane roof 17.Other Page 2 of 4 Updated 10/17/18 OFFICE COPY Category/Subcategory Manufacturer Product Description Limitation of Use State# Local# E.SHUTTERS 1.Accordion 2. Bahama _ 3.Storm panels 4. Colonial 5. Roll-up 6. Equipment 7. Other F.STRUCTURAL COMPONENTS _ 1.Wood connector/anchor 2.Truss plates 3. Engineered lumber 4. Railing 5.Coolers-freezers 6. Concrete admixtures 7. Material 8. Insulation forms 9. Plastics 10. Deck-roof 11.Wall 12.Sheds 13.Other G. SKYLIGHTS 1. Skylight 2. Other H. NEW EXTERIOR ENVELOPE PRODUCTS 1. 2. Page 3 of 4 Updated 10/17/18 OFFICE COPY In addition to completing the above list of manufacturers, product description and State approval number for the products used on this project, the Contractor shall maintain on the job site and available to the Inspector, a legible copy of each manufacturer's printed specifications and installation instructions along with this Product Approval Sheet. I certify that this product approval list is true and correct to the best of my knowledge. I further certify that use of different components other than the ones listed in this document must be approved by the Building Official. *Contractor Name (Print Name):Kevin Hurley *Contractor Signature: *Company Name: Better Home Improvement *Mailing Address: 538 Park Avenue *City: Orange Park *State: Florida *Zip Code: 32073 *Telephone Number: 90q-(9---7R-L0?( *E-mail Address: mayagbhi@gmail.com Cell Phone Number: q Out-a-7 —Cg( 0 Fax Number: Cl6u.- Page 4 of 4 Updated 10/17/18 OFFICE COPY Florida Product Approval HardiePlank® Lap Siding • For use inside HVHZ: o HardiePlank Lap Siding fastener types, fastening schedule, and installation shall be in accordance with the Miami-Dade County Florida NOA 17- 0406.06. Consult the HardiePlank product installation instructions on the follow pages for all other installation requirements. • For use outside of HVHZ, o HardiePlank Lap Siding fastener types, fastening schedule, and installation shall be in accordance with Engineering Evaluation Reports RIO-2683-17, RIO-2687-17, or RIO-2688-17. Consult the HardiePlank product installation instructions on the follow pages for all other installation requirements. , , NjJamesHardie HardiePlank >�. Lap Siding EFFECTIVE MAY 2016 — INSTALLATION REQUIREMENTS -PRIMED&COLORPLUS` PRODUCTS Visit www.hardieinstallation.COm for the most recent version. SELECT CEDARMILL© • SMOOTH • CUSTOM COLONIAL'SMOOTH •CUSTOM COLONIAL"ROUGHSAWN CUSTOM BEADED CEDARMILL°•CUSTOM BEADED SMOOTH • STRAIGHT-EDGE SHINGLE PLANK IMPORTANT:FAILURE TO INSTALL AND FINISH THIS PRODUCT IN ACCORDANCE WITH APPLICABLE BUILDING CODES AND JAMES HARDIE WRITTEN APPLICATION INSTRUCTIONS MAY LEAD TO PERSONAL INJURY,AFFECT SYSTEM PERFORMANCE,VIOLATE LOCAL BUILDING CODES,AND VOID THE PRODUCT ONLY WARRANTY.BEFORE INSTALLATION,CONFIRM THAT YOU ARE USING THE CORRECT HARDIEZONE'"PRODUCT INSTRUCTIONS. INSTALLATION OF HZ1 O®PRODUCTS OUTSIDE AN HZ1 O®LOCATION WILL VOID YOUR WARRANTY. TO DETERMINE WHICH HARDIEZONET" APPLIES TO YOUR LOCATION,VISIT WWW.HARDIEZONE.COM OR CALL 1-866-942-7343(866 9HARDIE) STORAGE&HANDLING: © CUTTING INSTRUCTIONS Store flat and keep dry and covered prior OUTDOORS INDOORS to installation.Installing siding wet or 1.Position cutting station so that wind will blow dust away from user 1.Cut only using score and snap,or shears(manual,electric or pneumatic). saturated may result in shrinkage at butt and others in working area. 2.Position cutting station in well-ventilated area 2.Use one of the following methods: joints.Carry planks on edge. Protect a.Best i.Score and snap edges and corners from breakage.James ii.Shears(manual,electric or pneumatic) -NEVER use a power saw indoors Hardie is not responsible for damage b.Better: i.Dust reducing circular saw equipped with a -NEVER use a circular saw blade that does not cavy the HardieBlade saw blade trademark caused by improper storage and handling HardieBlade saw blade and HEPA vacuum extraction -NEVER dry sweep—Use wet suppression or HEPA Vacuum of the product. c.Good. i.Dust reducing circular saw with a HardieBlade saw blade (only use for low to moderate cutting) �/ Important Note:For maximum protection(lowest respirable dust production),James Hardie recommends always using"Best"-level cutting methods where feasible. NIOSH-approved respirators can be used in conjunction with above cutting practices to further reduce dust exposures.Additional exposure information is available = ' at www.jameshardie.com to help you determine the most appropriate cutting method for your job requirements.If concern still exists about exposure levels or you do not comply with the above practices,you should always consult a qualdied industrial hygienist or contact James Hardie for further information. 50053105 GENERAL REQUIREMENTS: • HardiePlank®lap siding can be installed over braced wood or steel studs spaced a maximum of 24 in.o.c.or directly to minimum 7/16 in.thick OSB sheathing.See general fastening requirements.Irregularities in framing and sheathing can mirror through the finished application. • Information on installing James Hardie products over foam can be located in JH Tech Bulletin 19 at www.jamehardie.com • A water-resistive barrier is required in accordance with local building code requirements.The water-resistive barrier must be appropriately installed with penetration and junction flashing in accordance with local building code requirements.James Hardie will assume no responsibility for water infiltration. James Hardie does manufacture HardieWrap®Weather Barrier,a non-woven non-perforated housewrap',which complies with building code requirements. • When installing James Hardie products all clearance details in figs.3-14 must be followed. • Adjacent finished grade must slope away from the building in accordance with local building codes- typically a minimum of 6 In.in the first 10 ft.. Figure 1 Double ll Single ingl Wall ll • Do not use HardiePlank lap siding in fascia or trim applications. • Do not install James Hardie products,such that they may remain in contact with standing water. water-resistive barrier let-in bracing • HardiePlank lap siding may be installed on flat vertical wall applications only. rood or 24 in.o.c.max. • For larger projects,including commercial and multi-family projects,where the span of the ° �"ng �� wall is significant in length,the designer and/or architect should take into consideration the r coefficient of thermal expansion and moisture movement of the product in their design. ���` I� These values can be found in the Technical Bulletin"Expansion Characteristics of / James Hardie®Siding Products"at www.JamesHardie.com, ' l fil(r .-:;,..:;',.'; • DO NOT use stain,oil/alkyd base paint,or powder coating on James Hardie®Products. INSTALLATION: JOINT TREATMENT Figure 2 Nail line(If nail One or more of the following joint treatment optionsline is not / are required by code(as referenced 2009 IRC stud present place R703.10.2) (IwIINN ?1_ fastener A.Joint Flashing(James Hardie recommended) between 3/4 top f"ank from B.Caulking*(Caulking is not recommended resistive f?�� top of plank) 11% 14,41. barrier Nail 3/8 in.from / for ColorPlus for aesthetic reasons as the edge of plank Caulking and ColorPlus will weather I, �g o water-resistive different) .For the same reason, tlasning y ,, barrier do not caulk nail heads on o ColorPlus products.) l HardiePlank siding •o oolip fastener C."H" jointer cover '00 o0 o�Install a 1 1/4 in.starter strip to install planks in o o o v o ensure a consistent plank angle moderate contact at butt joints leave appropriate gap between planks and trim,then caulk."' Note:Field painting over caulking may produce a sheen difference when compared to the field painted PrimePlus. 'Refer to Caulking section in these instructions. 'For additional information on HardieWrap®Weather Barrier,consult James Hardie at 1-866-4Hardie or www.hardiewrap.com WARNING:AVOID BREATHING SILICA DUST James Hardie products contain respirable crystalline silica,which is known to the State of California to cause cancer and is considered by IARC and NIOSH to be a cause of cancer from some occupational sources. Breathing excessive amounts of respirable silica dust can also cause a disabling and potentially fatal lung disease called silicosis,and has been linked with other diseases. Some studies suggest smoking may increase these risks. During Installation or handling:(1)work In outdoor areas with ample ventilation;(2)use fiber cement shears for cutting or,where not feasible,use a HardieBlade®saw blade and dust-reducing circular saw attached to a HEPA vacuum;(3)warn others in the immediate area;(4)wear a properly-fitted,NIOSH-approved dust mask or respirator(e.g.N-95)in accordance with applicable government regulations and manufacturer instructions to further limit respirable silica exposures. During clean-up,use HEPA vacuums or wet cleanup methods-never dry sweep.For further information,refer to our installation instructions and Material Safety Data Sheet available at www.jameshardie.com or by calling 1-800-9HARDIE(1-800-942-7343). FAILURE TO ADHERE TO OUR WARNINGS,MSDS,AND INSTALLATION INSTRUCTIONS MAY LEAD TO SERIOUS PERSONAL INJURY OR DEATH. HS11119-P1/4 05/16 jr-Wig - CLEARANCE AND FLASHING REQUIREMENTS Figure 3 Figure 4 Figure 5 Figure 6 Roof to Wall Horizontal Flashing Kickout Flashing Slabs, Path,Steps to Siding Z-Flashing Asluired \ 40, "/ code x4in 1 -7 Min. DoMinn t4 caulk 1 in. 2 in. ' ' in. " 1 in.-2 in. N,,; /� r ib,4 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Deck to Wall Ground to Siding Gutter to Siding Sheltered Areas Mortar/Masonry • ,J,..,....-- ' ,/ L Flashing rf�/ Z-Flashing ••hing I Z FI..hing \ WOO F6 in. t 000Min.'/z in. n* . n.l Figure 12 Figure 13 Figure 14 Drip Edge Block Penetration Valley/Shingle Extension (Recommended in HZ10 11111111' pA�— ei Extend shingles /�'� Min.'%i r at lest 1 m.out f �'' 1 Iif � "• D� '� Eua1 fascivimf ent il �// IIIIIftlillBi. % icy FASTENER REQUIREMENTS ** Blind Nailing is the preferred method of installation for HardiePlanke lap siding products.Face nailing should only be used where required by code for high wind areas and must not be used in conjunction with Blind nailing(Please see JH Tech bulletin 17 for exemption when doing a repair).Pin-backed corners may be done for aesthetic purposes Only.Pin-backs shall be done with finish nails only,and are not a substitute for blind or face nailing. BLIND NAILING FACE NAILING Nails-Wood Framing Nails-Wood Framing •Siding nail(0.09 in.shank x 0.221 in.HD x 2 in.long) •6d(0,113 in.shank x 0.267 in.HD x 2 in.long) • 11 ga.roofing nail(0.121 in.shank x 0.371 in.HD x 1.25 in.long) •Siding nail(0.09 in.shank x 0.221 in.HD x 2 in.long) Screws-Steel Framing Screws-Steel Framing •Ribbed Wafer-head or equivalent(No.8 x 1 1/4 in.long x 0.375 in.HD)Screws •Ribbed Bugle-head or equivalent(No.8-18 x 1-5/8 in.long x must penetrate 3 threads into metal framing. 0.323 in,HD)Screws must penetrate 3 threads into metal framing. Nails-Steel Framing Nails-Steel Framing •ET&F Panelfast`x nails or equivalent(0.10 in.shank x 0.313 in.HD x 1-1/2 in. •ET&F pin or equivalent(0.10 in.shank x 0.25 in.HD x 1-1/2 in.long) long) Nails must penetrate minimum 1/4 in.into metal framing. Nails must penetrate minimum 1/4 in.into metal framing. OSB minimum 7/16 in. OSB minimum 7116 in. •Siding nail(0.09 in.shank x 0.221 in.HD x 1-1/2 in.long)* •11 ga.roofing nail(0.121 in.shank x 0.371 in.HD x 1.75 in,long) •Ribbed Wafer-head or equivalent(No.8 x 1 5/8 in.long x 0.375 in.HD). Stud �— 24 In.---0.C.max. Stud 24" V., o.C.max I1(((lla►wl Figure 15 Figure 16 1•v4 in.men. 1I"ilNll — i overlap Minimum overlap •L -.�— —� for Both Face Nail Line e — — - o %) and Blind Nailing 3/4 in:1 irj. i jig Blind Nail : p - -- min.1 1/4 in. I overlap f f water-resistive l ---- Water ResistiveL . -- barrier 11/4"min. Barrier Overlap Laminate sheet to be removed immediately after installation of each course for ColorPluse products. * When face nailing to OSB,planks must be no greater than 91/4 in.wide and fasteners must be 12 in.o.c.or less. **Also see General Fastening Requirements;and when considering alternative fastening options refer to James Hardie Technical Bulletin USTB 17-Fastening Tips for HardiePlanke Lap Siding. HS11119-P214 05/16 147-1—e. GENERAL FASTENING REQUIREMENTS PNEUMATIC FASTENING Fasteners must be corrosion resistant,galvanized,or stainless steel. James Hardie products can be hand nailed or fastened with a pneumatic tool. Electro-galvanized are acceptable but may exhibit premature corrosion. Pneumatic fastening is highly recommended. Set air pressure so that the James Hardie recommends the use of quality,hot-dipped galvanized nails. fastener is driven snug with the surface of the siding.A flush mount James Hardie is not responsible for the corrosion resistance of fasteners. attachment on the pneumatic tool is recommended. This will help control the Stainless steel fasteners are recommended when installing James Hardie® depth the nail is driven.If setting the nail depth proves difficult,choose a products near the ocean,large bodies of water,or in very humid climates. setting that under drives the nail. (Drive under driven nails snug with a smooth faced hammer-Does not apply for installation to steel framing). Manufacturers of ACQ and CA preservative-treated wood recommend spacer materials or other physical barriers to prevent direct contact of ACQ or CA preservative-treated wood and aluminum products.Fasteners used to attach ` ` ��� k1/4)` :4 countersunk, HardieTrim Tabs to preservative-treated wood shall be of hot dipped '` fill&add nail zinc-coated galvanized steel or stainless steel and in accordance to 2009 IRC snug flush DO NOT DO NOT R317.3 or 2009 IBC 2304.9.5. under drive nails staple Figure A Figure B • Consult applicable product evaluation or listing for correct fasteners type and placement to achieve specified design wind loads. PAINTING • NOTE:Published wind loads may not be applicable to all areas where Local DO NOT use stain,oiValkyd base paint,or powder coating on James Hardie® Building Codes have specific jurisdiction.Consult James Hardie Technical Products.James Hardie products must be painted within 180 days for primed Services if you are unsure of applicable compliance documentation. product and 90 days for unprimed.100%acrylic topcoats are recommended. • Drive fasteners perpendicular to siding and framing. Do not paint when wet.For application rates refer to paint manufacturers • Fastener heads should fit snug against siding(no air space).(fig.A) specifications.Back-rolling is recommended if the siding is sprayed. • Do not over-drive nail heads or drive nails at an angle. • If nail is countersunk,fill nail hole and add a nail.(fig.B) CUT EDGE TREATMENT • For wood framing,under driven nails should be hit flush to the plank with a Caulk,paint or prime all field cut edges.James Hardie touch-up kits are hammer(For steel framing,remove and replace nail), required to touch-up ColorPlus products. • NOTE:Whenever a structural member is present,HardiePlank should be fastened with even spacing to the structural member.The tables allowing CAULKING direct to OSB or plywood should only be used when traditional framing is For best results use an Elastomeric Joint Sealant complying with ASTM C920 not available. Grade NS,Class 25 or higher or a Latex Joint Sealant complying with ASTM • Do not use aluminum fasteners,staples,or clipped head nails. C834.Caulking/Sealant must be applied in accordance with the caulking/sealant manufacturer's written instructions.Note:OSI Quad as well as some other caulking manufacturers do not allow tooling. COLORPLUS®TECHNOLOGY CAULKING,TOUCH-UP&LAMINATE •Care should be taken when handling and cutting James Hardie®ColorPlus®products.During installation use a wet soft cloth or soft brush to gently wipe off any residue or construction dust left on the product,then rinse with a garden hose. •Touch up nicks,scrapes and nail heads using the ColorPlus®Technology touch-up applicator.Touch-up should be used sparingly. If large areas require touch-up,replace the damaged area with new HardiePlank®lap siding with ColorPlus Technology. •Laminate sheet must be removed immediately after installation of each course. •Terminate non-factory cut edges into trim where possible,and caulk.Color matched caulks are available from your ColorPlus®product dealer. •Treat all other non-factory cut edges using the ColorPlus Technology edge coaters,available from your ColorPlus product dealer. Note:James Hardie does not warrant the usage of third party touch-up or paints used as touch-up on James Hardie ColorPlus products. Problems with appearance or performance arising from use of third party touch-up paints or paints used as touch-up that are not James Hardie touch-up will not be covered under the James Hardie ColorPlus Limited Finish Warranty. PAINTING JAMES HARDIE®SIDING AND TRIM PRODUCTS WITH COLORPLUS®TECHNOLOGY When repainting ColorPlus products,James Hardie recommends the following regarding surface preparation and topcoat application: •Ensure the surface is clean,dry,and free of any dust,dirt,or mildew •Repriming is normally not necessary •100%acrylic topcoats are recommended •DO NOT use stain,oiValkyd base paint,or powder coating on James Hardie®Products. •Apply finish coat in accordance with paint manufacturers written instructions regarding coverage,application methods,and application temperature •DO NOT caulk nail heads when using ColorPlus products,refer to the ColorPlus touch-up section HS11119-P3/4 05/16 11./A.' = COVERAGE CHART/ESTIMATING GUIDE Number of 12 ft.planks,does not include waste COVERAGE AREA LESS OPENINGS HARDIEPLANK°LAP SIDING WIDTH SQ 51/4 61/4 71/4 71/2 8 81/4 91/4 91/2 12 (1 SQ=100 sq.ft.) (exposure) 4 5 6 61/4 6 3/4 7 8 81/4 10 3/4 1 25 20 17 16 15 14 13 13 9 2 50 40 33 32 30 29 25 25 19 3 75 60 50 48 44 43 38 38 28 4 100 80 67 64 59 57 50 50 37 5 125 100 83 80 74 71 63 63 47 6 150 120 100 96 89 86 75 75 56 7 175 140 117 112 104 100 88 88 65 8 200 160 133 128 119 114 100 100 74 9 225 180 150 144 133 129 113 113 84 10 250 200 167 160 148 143 125 125 93 11 275 220 183 176 163 157 138 138 102 12 300 240 200 192 178 171 150 150 112 13 325 260 217 208 193 186 163 163 121 14 350 280 233 224 207 200 175 175 130 15 375 300 250 240 222 214 188 188 140 16 400 320 267 256 237 229 200 200 149 17 425 340 283 272 252 243 213 213 158 18 450 360 300 288 267 257 225 225 167 19 475 380 317 304 281 271 238 238 177 20 500 400 333 320 296 286 250 250 186 This coverage chart is meant as a guide.Actual usage is subject to variables such as building design.James Hardie does not assume responsibility for over or under ordering of product. RECOGNITION:In accordance with ICC-ES Evaluation Report ESR-2290,HardiePlank®lap siding is recognized as a suitable alternate to that specified in:the 2006,2009,&2012 International Residential Code for One- and Two-Family Dwellings,and the 2006,2009,&2012 International Building Code,.HardiePlank lap siding is also recognized for application in the following:City of Los Angeles Research Report No.24862,State of Florida listing FL#889,Dade County,Florida NOA No.02-0729.02,U.S.Dept of HUD Materials Release 1263c,Texas Department of Insurance Product Evaluation EC-23,City of New York MEA 223-93-M,and California DSA PA-019.These documents should also be consulted for additional information concerning the suitability of this product for specific applications. ®2016 James Hardie Building Products.All rights reserved. Additional Installation Information, n TM,SM,and®denote trademarks or registered trademarks of James Hardie Technology Limited.8,1 is a registered trademark Warranties,and Warnings are available at Ja m eSHa idle of James Hardie Technology Limited. www,jameshardie,com Panelfast is a registered trademark of ET&F Fastening Systems,Inc. HS11119-P4/4 05/16 ii.:5 '.1-1/2,,' f� Cash Register Receipt Receiptt Number ,_.)1, , City of Atlantic Beach R11450 DESCRIPTION I ACCOUNT I QTY PAID PermitTRAK $55.00 RES19-0374 Address: 480 AQUATIC DR APN: 171818 5160 $55.00 BUILDING WALL SHEATHING 01/08/2020 RBE $55.00 BUILDING WALL SHEATHING 01/08/2020 455-0000-322-1002 0 $55.00 RBE TOTAL FEES PAID BY RECEIPT: R11450 $55.00 Date Paid: Thursday,January 09, 2020 Paid By: BETTER HOME IMPROVEMENT Cashier: CT Pay Method: CREDIT CARD 075137 Printed:Thursday,January 09, 2020 2:54 PM 1 of 1 ,"µ ry Cash Register Receipt Receipt Number City of Atlantic Beach R11610 JHl1) DESCRIPTION ACCOUNT I QTY PAID PermitTRAK $55.00 RES19-0374 Address: 480 AQUATIC DR APN: 171818 5160 $55.00 BUILDING SIDING IN PROGRESS 01/14/2020 RBE $55.00 BUILDING SIDING IN PROGRESS 01/14/2020 455-0000-322-1002 0 $55.00 RBE TOTAL FEES PAID BY RECEIPT: R11610 $55.00 Date Paid: Friday, January 31, 2020 Paid By: BETTER HOME IMPROVEMENT Cashier: CT Pay Method: CREDIT CARD 1 Printed: Friday,January 31, 2020 8:52 AM 1 of 1 0