133 Beach Ave RES18-0376 Product Eval Report Product Evaluation Report
per Rule 61G20-3,Florida Department of Business and Professional Regulation
Manufacturer: Jobsite Address:
Marvin Windows and Doors SCROGINS RESIDENCE MA RV I N'
401 States Ave NE 133 BEACH AVENUE
Warroad,MN 56763 ATLANTIC BEACH,FL 32233
Statement of Compliance:
This report evaluates the below-listed product per the requirements of FAC Product Approval Rule Chapter 61G20-
3.005(4)and through Florida Statute 553.8425 Local Product Approval. This product complies with the requirements
of the Florida Building Code 2017 excluding the HVHZ. The product meets sections;
• 104.11 Alternative materials,design and methods of construction and equipment,
• 1609.1.2 Protection of Openings,
• 1709.5 Exterior windows and doors assemblies;
o 1709.5.1 sub 3 All components of the alternate size unit shall be the same as the tested unit,
o 1709.8 Mullions occurring between individual windows,
• 2404.1 Glass design complies with ASTM E1300,and
• 2613.1 FRP exterior cladding flame spread index requirements nn
Product Description: Architectural Project Quote: BLJYWZZ,06/25/19
Marvin Signature,Double Hung G2,vertical mull clip design at sill, /ye
Front Left(MSTR Bath),vertical mull,span=76.00 by TW=37.63"
444'
A-Owners Retreat(NEW),vertical mull,span=-93.75 by TW=35.50". CO
Technical Documentation: _i
Conformance steps: (1)Review of FL 17635.1 and 17635.13 product approvals,
(2)Engineering analysis of vertical mull clip design at still,substituting new clip,and
(3)Mull end clip design anchor analysis
Installation Requirements:
Products must be installed in the opening per FL 17635.13 end clip design,modified by clip design on page 3 using;
a. SMS screw attachment to window(pre-drill as require)and
b. Concrete anchor through PT buck into Rough Opening.
Limitations and Conditions of Use;
Site specific Product Evaluation report for local approval—for use at 133 BEACH AVENUE,
Product Description Frame Size:Width x Height Design Pressure of(psf)
Vertical mull clip design at sill Unit and mull size in Product Description +/-42 psf ASD
*Ultrexe and PUR sills are made of an FRP material which is an NFPA Class C and B material respectively. Limitations regarding the height at ch
they may be installed can depend on the construction class and/or local codes.
Product Evaluation Report Expiration Date 1 February 2021 �me
Window Glass Design 5—Deluxe by Standards Design Group,Inc.,was used for glass thickness calculations. Microsoft Excel was 0
calculations.
0,1/
1 .
Certification of Independence: n$TStip \y
I,Stephen D.Fisher,the Professional Engineer pe this evaluation,have not now nor `a 0 a ct
financial interest in manufacturing,distributiolA n /product(s) for which this report is'iktte am an
employee of Marvin Lumber and Cedar,d �ttr' s•a$,Y�y I do not now,nor will I acquire,a financial interest
in any other entity involved in the aper l p NI or ucfat.
No. 47489state:
Signed: S (7:t ; I `'� 202o
Evaluated by. '-'� itally signed by Stephen Fisher 1p.tj
Stephen Fisher e:Zaz ,ep>b0o r
r„ Stephen D.Fisher PE,FL-047489
'j;°�'+,, 41OR` °r'' y��' Material and Building Science Engineer
4��? r :•�'''NI,:`��° Marvin Windows&Doors
Page 1 of 3
Technical Mullion Material Description:
Vertical mull clip design at sill
Reference Product Evaluation Reports:
FL 17635.1 and 17635.13, .
FL! Model,Number or Name Description
17535.1 CUDH-NG 4032 2W Cambiration Clad JI:-rate Double Hung-Next Generation mulled to Clad Ultimate '
Assembly Double Hung-Next Generation 2W Combination Assembly 407-H-
1127
Limits of Use !Certification Agency Certificate
Approved for use in HVHZ:No i FL17635 R4 C CAC CCL for Marvin 407-H_1127.28.29.p�f
Approved for use outside HVHZ:Yes 1 Quality Assurance Contract Expiration Date
Impact Resistant:No 08111/2022
Design Pressure: -50!-50 'Installation Instructions
Other:Max Size of Mulled Assembly: 2299mm x 1816mm(90 1/V x f117635 R4 II 00094934.pdf
71 1/21,Tributary Width 1149mm Span 1816mm;Glass makeup,IG Verified By:Window and Door Manufacturer Association
comprised of two 3.1mm annealed panes separated by a 16mm metal Created by Independent Third Party:
spacer.Glass complies with ASTM E1300. Evaluation Reports
Created by Independent Third Party:
17;51.5.13 CUDHT-NG 2W over CUDH-NG 2W Vertical Clad Ultimate Double Hung Transom-Next Generation 2w over Clad Ultimate
Mull(3/8"MRF)2W2H i Double Hung-Next Generation 2W,Vertical Mull(3/8'MRF)2W2H 4074,-
1127
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:tic fL17635 R4 C CAC CCL for tlarvin 407-H-1127.26,27.pdf
Approved for use outside HVHZ:Yes Quality Assurance Contract Expiration Date
I Impact Resistant:No 09/29/2022
Design Pressure:-65;-55 Installation Instructions
Other:Max Size Mulled Assembly:2308mm x 2113mm(90 718'x 83 3:15'; - I-L17635 R4 II 00095Qu141t
Operator 5.Transom Glass makeup,IG comprised of two 3.1mm annealed Verified By:Window and Door Manufacturer Association
i panes separated by a 16mm metal spacer.Glass complies with ASTM E1330. Created by Independent Third Party:
Evaluation Reports
Created by independent Third Party:
Reference sections from the 2017 FL Building Code-Building,Sixth;
[A] 104.11 Alternative materials,design and methods of construction and equipment.
The provisions of this code ale not intended to prevent the installation of any material or to prohibit any design or method of construction not specifically
preschoed by this code. provided that any such alternative has been approved. An alternative material. design or metnod of construction shall be
approved where the ouiiding cffc,a;finds that the proposed design is satisfactory and complies with the intent of the provisions of this code and that the
material. method or worK offered is for the purpose intended not less than the equivalent of that prescribed in this code in quality. strength.
effectiveness.fire res'srance durability and safety.Where the alternative material,design or method of construction is not approved,the buudrng official
shall respond in writing,stating the reasons why the alternative was not approved
1609.1.2 Protection of openings.
In ,r:id-borne debris regions,grazed openings in buildings Sfrali be impact resistant or protected with an impact-resistant covering meeting the
reel;. of ANSI/DASMA 115(for garage doors and rotting doors)or TAS 201, 202 and 203, AAMA 506, ASTM E1996 and ASTM E1886
referenced herein,or an approved impact-resistant standard as follows
1 Glazed openings located within 30 feet(9144 mm)of grade shall meet the requirements of the large missile test of ASTM E1996.
2. Glazed openings located more than 30 feet(9144 mm)above grade shall meet the provisions of the small missile test of ASTM E1996
1709.5 Exterior window and door assemblies.
The design pressure rating of exterior windows and doors in buildings shall be determined in accordance with Section 1709.5.1 or 1709.5.2. For the
purposes of this section.the required design pressure shall be determined using the allowable stress design load combinations of Section 1605.3.
Excc; . ;,ii(one _ .,:;;-iatury or be designed aisi
engineered ur accordance with accepted engineering practices by a Honda registered design professional Signed and sealed copies of the rippat
analysis and calculations shall be provided to the building oficial upon permit application ii�i
Printed copies of this document are not considered signed and sealed and the au bArion c
must be verified on any electronic copies.
QAO �
Page 2 of 3 C?�
-,---
1 1
1 reverse angle
9/32 x 29/32 bracket
spacer block
-- #10 X 2 1 /2 SM S
It2X8 pt buck
13
I �� 4 /
8" concrete
- . 'i" block poured
solid
`
r-- e _ (4.,,�b,A.
,.....P. it.e.4%{, C.,.4., 1,-1,.. i •
2.•A 2 12 y. Yy' A,. p F' - PT 1.4.—k.,,
AS- ,. In
3,1,1_ lobi c
O.1°16 DtP bR1tiT1{v_.,,
691..Ac6= o-.451 Dna
*-lo_risx-eh' / SPC.ac.ES
KrLT1 K,Ji1L Gen li+ _`
4-______ --- ?orx }lex H�a 1/4` O
`.a Pectin lra.1. =>4e•AT `���
114°N
.1,2S- I -.:',0‘)C1 p s', ion wY QjQ
1.38 A� l/
1,00 -1 l'..1. f _ 1 _': 1,So O' �\`�
7 J\
0 0 0 1 0 0 0
1 i
i.
al In
6 jo 1:
e r N c
(20zs r'.En
S H 8a.E. g($1 P -'5 413
MARVIN PROJECT: Cust.#
DRAWING DATE: cust. name:
special ENTRY DATE:
0 calculations � t4 DRAWN BY: order#
Product Evaluation Report
per Rule 61G20-3,Florida Department of Business and Professional Regulation
Manufacturer: Jobsite Address:
Marvin Windows and Doors SCROGINS RESIDENCE M A RV I N
401 States Ave NE 133 BEACI I AVENUE
Warroad,MN 56763 ATLANTIC BEACH,FL 32233
Statement of Compliance
This report evaluates the below-listed product per the requirements of FAC Product Approval Rule Chapter 61G20-
3.005(4)and through Florida Statute 553.8425 Local Product Approval. This product complies with the requirements
of the Florida Building Code 2017 excluding the HVHZ. The product meets sections;
• 104.11 Alternative materials,design and methods of construction and equipment,
• 1609.1.2 Protection of Openings,
• 1709.5 Exterior windows and doors assemblies;
o 1709.5.1 sub 3 All components of the alternate size unit shall be the same as the tested unit,
o 1709.8 Mullions occurring between individual windows,
• 2404.1 Glass design complies with ASTM E1300,and
• 2613.1 FRP exterior cladding flame spread index requirements
Product Description: Architectural Project Quote: BLJYWZZ,06/25/19 Q�
Marvin Signature,Double Hung G2,vertical mull clip design at sill, ��`
Front Left(MSTR Bath),vertical mull,span=76.00 by TW=37.63" `��
A-Owners Retreat(NEW),vertical mull,span=93.75 by TW=35.50'.
Technical Documentation: O
Conformance steps: (1)Review of FL 17635.1 and 17635.13 product approvals,
(2)Engineering analysis of vertical mull clip design at still,substituting new clip,and
(3)Mull end clip design anchor analysis
Installation Requirements:
Products must be installed in the opening per FL 17635.13 end clip design,modified by clip design on page 3 using;
a. SMS screw attachment to window(pre-drill as require)and
b. Concrete anchor through PT buck into Rough Opening.
Limitations and Conditions of Use;
Site specific Product Evaluation report for local approval—for use at 133 BEACH AVENUE,
Product Description Frame Size:Width x Height Design Pressure of(psf)
Vertical mull clip design at sill Unit and mull size in Product Description +/-42 psf ASD
*Ultrex0 and PUR sills are made of an FRP material which is an NEPA Class C and 13 material respectively. Limitations regarding the height at which
they may be installed can depend on the construction class and/or local codes.
Product Evaluation Report Expiration Date]February 2021
littlal
Window Glass Design 5—Deluxe by Standards Design Group,Inc.,was used for glass thickness calculations. Microsoft Excel was v
calculations.
f.,,
� �`O 7 aei'
CI:g
Certification of Independence:
2 �'oc
I,Stephen D.Fisher,the Professional Engineer pe this evaluation,have not now nor vip•1,, y ct
financial interest in manufacturing,distributi a...Le1 3 oduct(s)for which this report rs s�t�e am an
employee of Marvin Lumber and Cedar, l-i ss.a f. I do not now,nor will I acquue,a financial interest
in any other entity involved in the appres�al p" s eep.
4 la�A ;O
A
No. 47 9 \f ::
Si ed: c "t •
I
gn t ) � �:;mate: I 1 Z02/0
Evaluated by: r 6` gitally signed b Stephen Fisher;'LRS m•
Stephen Fisher �' e:202 y 1P 600' I. "�'
vo �u ejv� f'"7'' Stephen D.Fisher PE,FL-047489
1�o'c �, etmot:42- ,,...•(!',,,',,i.' Material and Building Science Engineer
4�/B/B 0�.....I%!: `. Marvin Windows&Doors
Page 1 of 3
Technical Mullion Material Description:
Vertical mull clip design at sill
Reference Product Evaluation Reports:
FL 17635.1 and 17635.13, .
FL Y i t4odet,Number or Name Description
17535.1 CUDH-NG 4032 2W Combination I Clad Ultimate Double Hung Next Generation mulled to Clad Ultimate
Assembly Double Hung-Next Generation 2W Combination Assembly 407-H-
1127
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Ito Et17635 11.4 C,AC CCL for Marvin 407-1-i-1127.28,29.120
Approved for use outside 5P/HZ:Yes Quality Assurance Contract Expiration Date
Impact Resistant:No 08/11/2022
Design Pressure: +50/-50 Installation Instructions
Other:flax Size of Mulled Assembly:2299mm x 1816mm(90 1/2'x 1117635 R4 it 00094934.0(
71 1/2'),Tributary Width 1149mm Span 1816mm;Glass makeup,IG Verified By:Window and Door Manufacturer Association
comprised of tot 3.1mm annealed panes separated by a 16mm metal j Created by Independent Third Party:
spacer.Glass compiles with ASTM 81300, Evaluation Reports
Created by Independent Third Party:
117635.13 I CUGHT-NG 2W over CUDH-MG 2W Vertical I Clad Ultimate Double Hung Transom-Next Generation 2W over Clad Ultimate
Mull(3/8"MRF)2W2H I Double Hung-Next Generation 2W,Vertical dull(3/8"MRF)2W2H 407-H- :
11127
:Limits of Use I Certification Agency Certificate
Approved for use In HVHZ:No I Fi1763.i R4 S 71C.ScLLocsrvin-iu7-l1-1.b?J._,1Sz, pri_f I
Approved for use outside HVHZ:Yes i Quality Assurance Contract Expiration Date i
Impact Resistant:Ne 109/29/2022
Design Pressure:+65/-55 I Installation Instructions
Other:Max Size Mulled Assembly:2308mm x 2113mm(90 7/8':<83 3/15"1 a.az633 R4 II Q10_2,5_0.1,0,11
;Operater s Transom Glass makeup,IG comprised of two 3.1mm annealed Verified By:Window and Door Manufacturer Association
canes separated by a 16mm metal spacer.Glass complies with ASTM 81300. Created by Independent Third Party:
Evaluation Reports .
Created by Independent Third Party:
Reference sections from the 2017 FL Building Code-Building,Sixth;
[A] 104.11 Alternative materials,design and methods of construction and equipment.
The provisions of this code are not intended to prevent the Installation of any material or to prohiba any design or method of construction not specifically
prescrioed by this code, provided that any such alternative has been approved. An alternative material. des!gn or metnod of construction shall be
approved where the build ig orfx/e7 finds that the proposed design Is satisfactory and complies with the intent of the provisions of this code and that the
material, method or wore offered Is. for tne purpose intended, not less than the equivalent or that prescribed in tris code In quality, strength,
effectiveness.fire resisrance durability and safety,Where the alternative material,design or method of construction Is not approved,the building official
shall respond In writing,stating tile reasons why the alternative was not approved.
1609.1.2 Protection of openings.
In wind-borne debris region ,gtzazed openings in buildings shall be impact resistant or protected with an impact-resistant covering meeting the
requirements of ANSI/DASMA 115(for garage doors and rotting doors)or TAS 201, 2.02 and 203,AAMA 506,ASTM E1996 and ASTM E1886
referenced herein,or an approved impact-resistant standard as follows:
1. Glazed openings located within 30 feet(9144 mm)of grade shall meet the requirements of the large missile test of ASTM El 996.
2. Glazed openings located more than 30 feet(9144 mm)above grade shall meet the provisions of the small missile test of ASTM El 996.
1709.5 Exterior window and door assemblies.
The design pressure rating of exterior windows and doors In buildings shall be determined in accordance with Section 1709.5.1 or 1709.5.2. For the
purposes of this section.the required design pressure shall be determined using the allowable stress design load combinations of Section 1605.3.
Exception:Custom doors.Custom(one-ofa-kind)exterior door assemblies shall be tested by an approved testing laboratory or be designed and
engineered in accordance vellii accepted engineering practices by a Florida registered design professional.Signed and seated copies of the ratal
analysis and calculations shall be provided to the building official upon permit application.
Printed copies of this document are not considered signed and sealed and the au a',non co \/
must be verified on any electronic copies. ` i k? \/
#
Q
Page2of3 \1'
1
;
1
T
I
I ..
}
i n reverse angle
9/32 x 9/32 -I�-. bracket
I spacer bi ck
I - #10X21 /2SMS
I 1 __ 1 �
. 2X8 pt buck
17
- C°
‘..1.
��•.4 8" concrete .
- _ `��' block poured
r ____...............,._..� solid
•
/ 1
As^,w.. A°�•c �"
3,1.,-L c.lis.v.t
0,MOUl'fh ba.ic .Tib2v.
10%tis% XV124 / S11/PLTTAc ES y
/
1 ` _�. /�Gl V�X V1eM .1/4)H
dtk
.O.PLo.n S.,kw/. Se.t,,,,T 1P1‘ ,,
IM'r. v_orf.c0:1,14•r...1.S. w
ik., ,,'
l,sa - Q
oix
o . 4''o 0 l 0 o ro
91 ,0 1nr° 1 I
O o MG
c
(7.17 P5c�
S HDLE gpsE: ‘ ,.•' sD
mARinN PROJECT: Cust.#
DRAWING DATE:
cust. name:
special ENTRY DATE:
calculations $ DRAWN BY: order#
D221:04 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 1
DENISEG
Customer Name : COASTAL SASH &DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : C0J01434 Order Date : 11-JUL-19
Line Unit-id Qty Mark Unit NFRC Unit Description U-val SHGC VLT Energy Star
Certification Product Number Glazing Comment ER Divider Comment
Line Unit-id Qty CCL WDMA Product Description
Test Rating and ASTM Certification Product ID -- Size -- DP Rating -- Certifing Agency
1 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
1 A2 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
2 Al 1 921 UL AWN
AAMA/WDMA/CSA/101/I.S.2/A440-11� LC-PG50 1016X1197 mm (40X47.13 in)
d®o 33iLC-PG50
1016X1197+50/-50
dQ
FL10323
3 Al 1 1113 UL OSWFRDR
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC- PG50 1845X2426 mm (72.63X95.5 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC- PG50 +50/-50tO
LC-PG50 1845X2426 —4s.
FL4809 '1 - d O V
4 Al 2 1127 UL DBLHNG G2 " ' 0
1149X2223 mm (45.25X87.5 in) S) \V///
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC PG50 t, /
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50 ��IL/
LC-PG50 1149X2223 , 'T°'' 4/ \
FL17635 /‘
D22R04 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 2
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : COJ01434 Order Date : 11-JUL-19
5 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
5 A2 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
5 A3 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
5 B1 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
5 B1 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781 w
et
5 B2 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC-PG50 +50/-50 ��� \/
LC-PG50 1149X2223 46_4\C°)
FL17635 0
$2.‘c)41
5
D22R04 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 3
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : C0J01434 Order Date : 11-JUL-19
5 B2 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
5 B3 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
6 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
6 B1 1 1113 UL OSWFRDR
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC- PG50 1845X2426 mm (72.63X95.5 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC- PG50 +50/-50
LC-PG50 1845X2426
FL4809
7 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781 e
7 B1 1 1113 UL OSWFRDR \
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC- PG50 1845X2426 mm (72.63X95.5 in) �� /
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC- PG50 +50/-50icl \
LC-PG50 1845X2426
FL4809 �'j. P0.# 76
O �e
c;.
D22R04 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 4
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : C0J01434 Order Date : 11-JUL-19
8 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
8 A2 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
8 A3 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
8 B1 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
8 B1 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
8 B2 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in) Nome
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50 �C S
�
LC-PG50 1149X2223 ��, �
FL17635
D22R04 • 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 5
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : C0J01434 Order Date : 11-JUL-19
8 B2 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
8 B3 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
9 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
10 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
11 Al 2 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223 _`
FL17635 �4
11 A2 2 1127 UL DBLHNG G2 `/
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in) *ti)-
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635 •Q#
cPs G��
D22R04 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 6
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : C0J01434 Order Date : 11-JUL-19
12 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
13 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
13 A2 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
14 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
15 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
15 A2 1 1127 UL DBLHNG G2 e '=a
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in) a1
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 ..*:.,IV'Ib `/
LC-PG50 1149X2223 4'" '
FL17635 its'
D22R04 • 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 7
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : C0J01434 Order Date : 11-JUL-19
16 Al 6 921 UL AWN
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC-PG50 1016X1197 mm (40X47.13 in)
LC-PG50 +50/-50
1016X1197
FL10323
17 Al 1 921 UL AWN
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC-PG50 1016X1197 mm (40X47.13 in)
LC-PG50 +50/-50
1016X1197
FL10323
18 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
19 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
20 Al 2 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781 ��
20 B1 2 1127 UL DBLHNG G2
\7
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in) ��
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223 /
FL17635 ,Q*
\e c.,
D22P-.04 • 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 8
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : COJ01434 Order Date : 11-JUL-19
21 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
21 B1 1 1113 UL OSWFRDR
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC- PG50 1845X2426 mm (72.63X95.5 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC- PG50 +50/-50
LC-PG50 1845X2426
FL4809
22 Al 1 1117 UL DIR GLZ POLY
AAMAANDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60
CW-PG50 2134X2464
FL4781
22 B1 1 1113 UL OSWFRDR
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC- PG50 1845X2426 mm (72.63X95.5 in)
AAMA/WDMA/CSA/101/I.S.2/A440-11 LC- PG50 +50/-50
LC-PG50 1845X2426
FL4809
23 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
24 Al 1 1117 UL DIR GLZ POLY
AAMA/WDMA/CSA/101/ I.S.2/A440-08 CW-PG50 2134X2464 mm (84X97 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 CW-PG50 +50/-60 <*'*� \/
CW-PG50 2134X2464
FL4781
5
D22R04 • 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 9
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : COJ01434 Order Date : 11-JUL-19
25 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
26 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
26 A2 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
27 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
28 Al 2 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
28 A2 2 1127 UL DBLHNG G2 i /
1149X2223 mm (45.25X87.5 �
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 in) /
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-501/4
LC-PG50 1149X2223 /
FL17635 CY#
5
D22R04 • 10-JAN-20 08:49:28 AM
V11.00.01 Sales Order Energy and Performance Information Summary Page 10
DENISEG
Customer Name : COASTAL SASH & DR/JACKSONVILLE
Customer Address : 345 STATE ROAD 207
Order Number : COJ01434 Order Date : 11-JUL-19
29 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMAANDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
30 Al 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/ I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
30 A2 1 1127 UL DBLHNG G2
AAMA/WDMA/CSA/101/I.S.2/A440-08 LC-PG50 1149X2223 mm (45.25X87.5 in)
AAMA/WDMA/CSA/101/ I.S.2/A440-11 LC-PG50 +50/-50
LC-PG50 1149X2223
FL17635
6QP��
5