Loading...
426 Skate Rd ROOF20-0015 Mod Bit ROOF NON SHINGLE PERMIT PERMIT NUMBER CITY OF ATLANTIC BEACH ROOF20-0015 &f800 SEMINOLE ROAD ISSUED: 3/5/2020 ATLANTIC BEACH. FL 32233 EXPIRES: 9/1/2020 MUST CALL INSPECTION PHONE LINE (904) 247-5814 BY 4 PM FOR NEXT DAY INSPECTION. ALL WORK MUST CONFORM TO THE CURRENT 6TH EDITION (2017) OF THE FLORIDA BUILDING CODE, NEC, IPMC, AND CITY OF ATLANTIC BEACH CODE OF ORDINANCES . ALL CONDITIONS OF PERMIT APPLY, PLEASE READ CAREFULLY. NOTICE: In addition to the requirements of this permit,there may be additional restrictions applicable to this property that may be found in the public records of this county,and there may be additional permits required from other governmental entities such as water management districts,state agencies,or federal agencies. JOB ADDRESS: PERMIT TYPE: DESCRIPTION: VALUE OF WORK: 426 SKATE RD ROOF NON SHINGLE MODIFIED BITUMEN ROOF $6900.00 TYPE OF REAL ESTATE ZONING: BUILDING USE SUBDIVISION: CONSTRUCTION: NUMBER: GROUP: 171559 0000 ROYAL PALMS UNIT 02A3.00 COMPANY: ADDRESS: CITY: STATE: ZIP: PIMENTEL ROOFING INC 402 St. Augustine Blvd. JACKSONVILLE FL 32250 BEACH OWNER: ADDRESS: CITY: STATE: ZIP: MCDANIEL HARDY JOSEPH PO BOX 331514 ATLANTIC BEACH FL 32233-1514 WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT. LIST OF CONDITIONS I Roll off container company must be on City approved list . Container cannot be placed on City right-of-way. DESCRIPTION ACCOUNT QUANTITY PAID AMOUNT BUILDING PERMIT 455-0000-322-1000 0 $85.00 BUILDING PLAN CHECK 455-0000-322-1001 0 $42.50 STATE DBPR SURCHARGE 455-0000-208-0700 0 $2.00 STATE DCA SURCHARGE 455-0000-208-0600 0 $2.00 TOTAL:$131.50 Issued Date: 3/5/2020 1 of 2 r0...v.',A ROOF NON SHINGLE PERMITiiiPERMIT NUMBER �s °; ROOF20-0015 r , CITY OF ATLANTIC BEACH �� "� ISSUED: 3/5/2020 J,; ,� 800 SEMINOLE ROAD EXPIRES: 9/1/2020 ATLANTIC BEACH, FL 32233 Issued Date:3/5/2020 2 of 2 r (To�si..An;.�J,wl, City of Atlantic Beach I APPLICATION NUMBER �S i� 1, Building Department be assigned by the Building Department.) 800 Seminole Road RooF- Atlantic Beach, Florida 32233-5445 Z.CDDOLS / Phone(904)247-5826 • Fax(904)247-5845 /Z ti O i3 0.}›/ E-mail: building-dept@coab.us Date routed: City web-site: http://www.coab.us APPLICATION REVIEW AND TRACKING FORM Property Address: 4 z __ �,. ( E �L.) Department review required Ye No uildi� l Applicant: P 1 Me--1\) t c-_C_ RooF, K..)C1� Planning &Zoning /� Tree Administrator Project: I\J `CUD . I�ci ROOF Public Works Public Utilities Public Safety Fire Services Review fee $ Dept Signature Other Agency Review or Permit Required Review or Receipt Date of Permit Verified By Florida Dept. of Environmental Protection Florida Dept.of Transportation St.Johns River Water Management District Army Corps of Engineers Division of Hotels and Restaurants Division of Alcoholic Beverages and Tobacco Other: APPLICATION STATUS Reviewing Department First Review: roved. Denied. ['Not applicable (Circle one.) Comments: BUILDING f J PLANNING &ZONING Reviewed by: _ __ Date:3JL/1c C TREE ADMIN. Second Review: ['Approved as revised. Denied! Not applicable ❑ pp n PUBLIC WORKS Comments: PUBLIC UTILITIES PUBLIC SAFETY Reviewed by: Date: FIRE SERVICES Third Review: Approved as revised. ['Denied. Not applicable Comments: Reviewed by: Date: Revised 05/19/2017 E "17r%, Building Permit Application �pdatedl0/9/18 City of Atlantic Beach Building Department 0FFICE C0PY "*ALL INFORMATION 800 Seminole Road, Atlantic Beach, FL 32233 HIGHLIGHTED IN GRAY Jt �r IS REQUIRED. Phone: (904) 247-5826 Email: Building-Dept@coab.us Yom, Job Address: x[ 26 Skate Poi AiI(.milc &I) 32Z33Permit Number: RC�C�f= 0 '__ (5 COT(b Legal Description 31 - 10 11- 2 S'29 E Kir PT 01 Kota( Paln11S lint 74 196k (q RE# 1115 5 1 - 0000 Valuation of Work(Replacement Cost)$ 0 C7 00 Heated/Cooled SF 10 56 Non-Heated/Cooled 3'10 • Class of Work: DNew DAddition DAlteration IRepair DMove DDemo DPool DWindow/Door • Use of existing/proposed structure(s): ❑Commercial Li1Residential • If an existing structure,is a fire sprinkler system installed?: DYes I'No ui rt • Will tree(s)be removed in association with proposed project?DYes(must submit separate Tree Removal Permit)-: J7No Describe in detail the type of work to be performed: ,/Y1ot7(t F,'ed 511- vmevl S el 4' Adhered Nr- J z Q v P'ocf R ep l ice �e�rt s < M 6 � �La } � w Florida Product Approval# F L. Z 3 3 — K rl b for multiple products use product appitcy jo nLA o Property Owner Information C H < a Name TO S-eph Mc Dahl&I Address 5 .� 44\I rdt S'f O Z R ct City Nei:4144e beach State F'L. Zip 3 Z Z b b Phone '10 -) Cf R 3 22. c lo h 0 E-Mail 3 urcn ja 1 g 9 it . GG.�1 CC <C w Owner or Agent(If Agent,Power of Attorney or Agency Letter Required) (-0 w ne r u. Ec2 O w w 5: Contractor Information >, a. CC m Name of Company /'AnSul fe I Rao I;'fig, Qualifying Agent iZ c evi 1-e LU 1`- L i= ' w Address 4401 St; Ai gvi ti ee / /: City Tax /3r./i State 1=L Zip 3 2. .. . "' u) L w Office Phone cloy ri q/ 6 ] le Job Site Contact Number 5 State Certification/Registration# CCC 13 3 0 4135 E-Mail p 144 i 71:61 YDo'(ig P 4lai/.6,041 D_ et Architect Name&Phone# Engineer's Name&Phone# Workers Compensation Insurer OR Exempt le-Expiration Date S- 26 -2.020 Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a permit and that all work will be performed to meet the standards of all the laws regulating construction in this jurisdiction.I understand that a separate permit must be secured for ELECTRICAL WORK, PLUMBING,SIGNS, WELLS, POOLS, FURNACES,BOILERS,HEATERS,TANKS,and AIR CONDITIONERS,etc. NOTICE:In addition to the requirements of this permit,there may be additional restrictions applicable to this property that may be found in the public recordsofthis:county,and. there may be additional permits required from other governmental entities such as water management districts,state agencies, pr federal agencies. OWNER'S AFFIDAVIT:I certify that all the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and zoning. F EB 2 5 2020 WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTgitctl0JON F5N ? :nt TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTO: ► eitialfilitiiIntic Beach, H.. RECORDING YOUR NOTICE OF COMMENCEMENT. & Ad. (Signature of Owner or Agent) / (Signature of Contractor) h Signed and sworn to(or affirmed)before me this 7.0 day of Signed and sworn to(or affirmed)before me thi day of f4littly ,_222C-L,by ea • - '/ v-w�.`., c'd r ,2-0 by r . i� ature•a ry) '- ��'Si nat qt�(�}, �ANIuEL� ERNEY 1 Notary Public,State of Flor".a Mrs ErrollMy Comm.Expires 8/17/2 Not [ ]Personally Known c Publio [ Personally Known OR roduced Identific ,P li et pond. [ ]Produced Identification Commission No.GG135675 Type of Identification: • 4-y _ was OI ' Type of Identification: iv) PIA,-C,PA,-C,er,^ 010,101111011 PIR 00 943900 Per PT/ i J 0Fc2C, �G�S NOTICE OF COMMENCEMENT /7 ` ‘g'9 e)6 O State of r b(7r I c a Tax Folio No. County of / tivaJ OFFICE COPY To Whom It May Concern: The undersigned hereby informs you that improvements will be made to certain real property, and in accordance with Section 713 of the Florida Statutes,the following information is stated in this NOTICE OF COMMENCEMENT. _ Legal Description of property being improved: '3 / 16 1 - 7 5 2 q gl P F 1 0.f goy a j Palms j,, ()pit Z A it Address of property being improved: U Z b Sa to lot At on ti 9c/i Ft 3 2 Z 3, 1\,, General description of improvements: IOO F e lac e/Rent Owner: TIIP aa//li�F'/ Address: 5 3 3 Myra s N ptime g(h FL 3220 Owner's interest in site of the improvement: S(,t le t. Fee Simple Titleholder(if other than owner): — Name: t..)Contractor: / ct ynl men /.--e I ?m&4t1 , J / _ Address: `�'0Z 4-rt t• V�t i A-} ORA f I.c 3�� Telephone No: Gln ' b Fax No: Surety(if any) — Address: Amount of Bond$ Telephone No: Fax No: Name and address of y person making a loan for the construction of the improvements Name: Wt. Address: Phone No: Fax No: Name of person within the State of Florida,other than himself,designated by owner upon whom notices or other documents may be served: Name: Address: Telephone No: Fax No: In addition to himself, owner designates the following person to receive a copy of the Lienor's Notice as provided in Section 713.06(2)(b), Florida Statues. (Fill in at Owner's option) Name: /J I Address: Telephone No: Fax No: Expiration date of Notice of Commencement(the expiration date is one(1)year from the date of recording unless a different date is specified): Zaire Emil or,SPACE FOR RECORDER'S USE ONLY OWNER State of Florida My Commission Expiry Doc#2020043780,OR BK 19115 Page 1632, Signed: ` Number Pages:1 Before fie this 2a day of 19 in the Cour3Zilbival,State Recorded 02/25/2020 10:51 AM, Of Florida,has personally appeared Nk. Ie Her RONNIE FUSSELL CLERK CIRCUIT COURT DUVAL Notary Public at Large,State of Florida County of COUNTY RECORDING $10.00 My commission expires: O5- 71s Personally Known: !/a t idu-d (,vi t 7-1)/PL, or Produced Identification: FL I)L, CertainTeed El Technical Data COMMERCIAL ROOFING SYSTEMS FLINTLASTIC' SA OFFICE COPY Self-Adhering SBS Modified Bitumen Mid Ply and Cap Sheet and SBS Modified Bitumen Base Sheet for SA Roof Systems. Product Flintlastic SA roofing membrane is a premium, self-adhering SBS modified bitumen roll roofing Information material suitable for use in accordance with CertainTeed specifications for most low slope roof system applications. Refer to the CertainTeed Commercial Roof Systems Specification Manual for complete self adhered roof system specifications and application requirements. ili . .. . The Flintlastic SA line of products is more than a single membrane, it is a complete roof 1 system designed for base and cap or base, mid-ply and cap roof system configurations. Use of Flintlastic SA Base permits complete mechanical attachment to nailable substrates, preserving the integrity of the substrate for future tear-offs and adding additional waterproofing performance capabilities to the overall system. For larger industrial/institutional applications, j's. Flintlastic SA Base, Mid Ply and Cap in combination represent a premium roof system capable of meeting the performance criteria of a larger roof. Use of Flintlastic SA Base also adds to the I Log_..... fire resistance of the roof system, enabling UL Listing of the roof system. When using self-adhering roofing products, particular attention must be paid to storage and handling, deck preparation, slope and drainage, and application requirements to assure a successful installation and long-term performance. Compliances Flintlastic SA roofing membranes are manufactured on state of the art, dedicated roofing lines specifically designed for the production of modified bitumen roofing membrane, and meet or ,o mo tow exceed the following ASTM standards: gam°``.^.' . f?0„ ASTM Standard F 4►-.,;,y. - Flintlastic SA Base D 4601, Type II Flintlastic SA Mid Ply D 6164 Color Companion Products' Flintlastic SA Cap D 6164 'L Classified by 'y ul Underwriters o� Laboratories,Inc. °,9j QQ�° Refer to the current UL Roof Systems Directory, or UL's web site, www.ul.com as to an External /%QUALITY 10°C.*'' for the most current information on UL listing for Flintlastic SA Products. Fire Exposure Only62P3 Flintlastic SA Base Flintlastic SA Mid Ply Flintlastic SA Cap Sheet FlintFlashTM SA Roll Dimensions 66'6" x 39-3/8" 33'11" x 39-3/8" 33'11"x 39-3/8" 33'11"x 13-1/8" (or 9-3/4") Thickness 1.5 mm 3.0 mm 4.0 mm 3.0 mm Weight 84 lbs 68 lbs 97 lbs 22.5 lbs (or 17 lbs) Coverage 2 Squares 1 Square 1 Square 1/3 Square(or 1/4 Square) Top Surface Permanent Film Permanent Film Mineral-Variety of Colors Permanent Film Bottom Surface Sand Removable Release Film Removable Release Film Removable Release Film Reinforcement Fiberglass Mat Polyester/Fiberglass Polyester/Fiberglass Polyester/Fiberglass Scrim Combination Mat Scrim Combination Mat Scrim Combination Mat Tensile(lin) 65/40 (MD/CD) 80/60 (MD/CD) 80/55 (MD/CD) 80/60 (MD/CD) Elongation(%) 6/5 (MD/CD) 50/55 (MD/CD) 50/55 (MD/CD) 50/55 (MD/CD) Packaging Palletized, Bands Individual Cartons Individual Cartons Individual Cartons, 20 rolls per pallet 20 rolls per pallet 20 rolls per pallet 3 rolls per carton (or 4) 60 rolls per pallet(or 80) Installation Refer to the CertainTeed Commercial Roof Systems Specification Manual for complete product installation details and requirements. Below is a general guideline: Deck Preparation CertainTeed recommends the use of Flintlastic SA Base in conjunction with all self-adhering membrane roof installations. Non-nailable roof decks may receive direct application of OFFICE COPY Installation Flintlastic SA Mid-Ply followed by Flintlastic SA Cap provided the deck is thoroughly primed using Flintlastic SA (cont'd) Primer. It should be noted without the use of a base sheet the membrane may be difficult to remove if removal is ever warranted, and certain UL and FM listings for the product may not apply. Flintlastic SA Base Nailable Substrates:Use standard nailing patterns and CT approved fasteners for attachment to nailable decks. Nail base sheet every 9" o.c. on side laps and every 18" on center in 2 staggered rows in the field of the sheet. Permanent top surface film is left in place. Non-Nailable Substrates:Prime non-nailable substrates such as concrete using FlintPrimeTM SA at the rate of .20 —.25 gals/square. Allow primer to dry, maximum 4 hours. Apply base sheet using hot asphalt at the rate speci- fied by CertainTeed. Insulation if used must be suitable to receive hot asphalt application such as FlintBoardTM ISO Plus. Overlap base sheet sidelaps 3" and endlaps 4". Always start membrane application at the low point of the roof and install all plies so that no laps are against the flow of water. Offset endlaps minimum 36". Flintlastic SA Mid Ply Apply to Flintlastic SA Base or suitable primed substrate overlapping sidela s 3" and endlaps 6". Work with lengths of Flintlastic SA Mid Ply appropriate for proper handling Posi ion and align cut lengt s of Mid Ply, staggering laps from the underlying ba Ye a minimum of 18" and offsetting endlaps 3 �. Once positioned, fold back the membrane halfway lengthwise and remove the release film, then ease back into place. Or, lift the end of the membrane and pull the split release film out as you walk the length of the membrane. Cut opposing corners of endlaps diagonally to minimize "T" seam joints and seal using FlintBond SBS Modified Bitumen Adhesive, trowel or caulk grade. Also apply a bead of FlintBond at side and endlaps. Use a heavy, weighted roller to smooth and secure the membrane. Permanent top surface film is left in place. Flintlastic SA Cap Apply to Flintlastic SA Base and/or Flintlastic SA Mid Ply working with lengths of membrane appropriate for proper handling and the same installation procedure as described for Flintlastic SA Mid Ply.Overlap si dela 4" and endlaps 6". Selvage edge with release strip is provided on Flintlastic SA Cap; position roll with selvage eage�"'ahe igh side of the roof. Once the first cap sheet membrane length is in place remove the top, sidelap release film before overlapping the second length of Flintlastic SA Cap Sheet. Staeuideplate lintlas ' SA Cap a minimum of 18" from those of the underlying Flintlastic SA Mid Ply, and be certain endlaps are also ..�.....�� �� »...�.� :ter � s agger d m nimum,3 . At end laps (or any overlap onto mineral surface), use trowel`gram on odi led B umen Adhe siv uniformly in a 1/16" to 1/8" layer wherever an overlap exists to ensure an adequate bond. Cut opposing corners of endlaps diagonally to avoid "T" seam joints. Use a heavy, weighted roller to smooth and secure the membrane. Verticals and Flashing Details Vertical transitions and flashing details require a minimum two-ply detail using Flintlastic SA Mid Ply and Flintlastic SA Cap, secured with Flintlastic Modified Bitumen Adhesive, trowel grade. FlintFlashTM SA pre-cut flashing rolls can also be used in conjunction with flashing details. Warranties CertainTeed offers a limited material Roof Membrane Warranty on Flintlastic SA roof membrane. Contact your nearest CertainTeed office for additional information and requirements. Technical CertainTeed provides technical assistance in the design, selection, specification and application guidelines Assistance for all CertainTeed Commercial Systems. Architectural and field representatives are available for consultation within each region. Precautions Do not attempt application if ice, snow, moisture or dew are present. Surface to be bonded to must be clean, dry and free from any dust or deterrent to adhesion. Ambient temperature must be 50°F or above. Do not attempt installation on roofs without adequate slope and drainage. Storage and SA rolls must be stored above ground, indoors, protected from the elements. Rolls that are improperly stored or Handling have been on hand for prolonged periods of time may lose their tack. Do not attempt to install rolls that do not exhibit an adequate bond. CertainTeed El 750 East Swedesford Rd. West Region South Region North Region P.O. Box 860 6400 Stevenson Blvd. 5525 MacArthur Blvd. Riverbridge Industrial Center COMMERCIAL ROOFING SYSTEMS Valley Forge, PA 19482 Fremont, CA 94538 Suite 900 800 W. Front Street (610)341-7000 (800)955-0811 Irving, TX 75038 Chester, PA 19013 WWW.certainteed.com Sales Support Group (800) 790-3347 fax (800)333-ROOF(7663) (866)297-ROOF(7663) (800) 233-8990 (972) 580-5645 fax (610)874-6170 fax ©2002 CertainTeed Corporation COMM-122 CertainTeed sanoofi a�, Technical Product Data Commercial Roofing OFFICE COPLEARN,MORE AT enenBstargov FLINTLASTIC® SA CAP SELF-ADHERING SBS MODIFIED BITUMEN CAP SHEET FOR SA ROOF SYSTEMS Product Product Use: Flintlastic" SA Cap is designed for use as a cap membrane in multi-ply self- Information adhered systems. It is suitable for use in the construction of various roof membrane assemblies over a variety of substrates. It is intended for use over Flintlastic®SA NailBase, Flintlastic®SA PlyBase or Flintlastic®SA MidPly. Product Composition and Features: Flintlastic SA Cap is manufactured using a high performance, stress-resistant polyester mat impregnated and coated with a superior grade of modified bitumen compound. It is surfaced on the bottom with a removable release film and on the top with mineral granules. The combination mat provides excellent tear and puncture resistance. Roll Dimensions: 393/8" x 32' 11" Nominal Coverage: One square Approximate Weight: 95 lbs. Top Surface: Mineral granules Back Surface: Removable release film Packaging: Individual cartons (20 rolls per pallet) Applicable Standards: Meets ASTM D6164, Grade G, Type I, D7505, D1970 and CGSB 37 GP-56M Type 1a, Class A, Grade 1, ICC-ES (ESR-1388), Miami-Dade, <_ Florida Buildng Code Statewide Approval (FL 2533 and FL 16709) and Texas CR C Department of Insurance (RC-47). Flintlastic SA Cap White is an approved .,„r lIMNOL ENERGY STAR.product for slopes greater than 2"/12". Initial Solar Reflectance: 0.27; Aged Solar Reflectance: 0.24; Thermal Emittance: 0.89. Flintlastic SA Cap White is also listed by the Cool Roof Rating Council (CRRC). The CRRC product code ID is 0668-0018. Technical Modified Bitumen Coating: Non-oxidized (flux)asphalt, blended with elastomeric Data styrene-butadiene-styrene (SBS) polymer. Support Mat:High performance, stress-resistant polyester mat. Test Description Test Method Results* Solar Reflectance Index(SRI): ASTM E1980 28/24 Tensile Strength: ASTM D5147 @ 73.4+/-3.6°F MD/XD 80/55 lbs./in. @ 0+/-3.6°F MD/XD 115/90 lbs./in. Elongation: ASTM D5147 @ 73.4+/-3.6°F MD/XD 60%/65% @ 0+/-3.6°F MD/XD 40%/40% Dimensional Stability: ASTM D5147 0.5% Low Temperature Flex: ASTM D5147 Pass @ 0°F Thickness: ASTM D5147 4.0 mm(160 mils) Tear Strength: @ 73.4+/-3.6°F MD/XD 110/80 lbs. *NOTE:Published results are nominal production values confirmed by independent laboratory testing. MADE IN U.S.A. OFFICE COPY Product Installation:Apply to Flintlastic SA NailBase, Flintlastic PlyBase and/or Flintlastic SA MidPly Application working with lengths of membrane appropriate for proper handling and the same installation procedure as described for Flintlastic SA MidPly. Overlap side laps 3"and end laps 6". Selvage edge with release strip is provided on Flintlastic SA Cap; position roll with selvage edge at the high side of the roof. Once the first cap sheet membrane length is in place, remove the top side lap to release film before overlapping the second length of Flintlastic SA Cap. Stagger side laps of Flintlastic SA Cap a minimum of 18"from those of the underlying Flintlastic SA MidPly and be certain end laps also are staggered minimum 36". At end laps (or any overlap onto mineral surface), use trowel grade FlintBond®modified bitumen adhesive uniformly in a ',;s'to 1/3" layer wherever an overlap exists to ensure an adequate bond. Cut opposing corners of end laps diagonally to avoid "T" seam joints. Use a heavy, weighted roller to smooth and secure the membrane. Deck Preparation:CertainTeed recommends the use of Flintlastic SA NailBase in conjunction with all self-adhering membrane roof installations on nailable substrates. Non-nailable roof decks may receive direct application of Flintlastic SA PlyBase or Flintlastic SA MidPly followed by Flintlastic SA Cap, provided the deck is thoroughly primed using FlintPrime°SA. It should be noted that without the use of a nailable base sheet, the membrane may be difficult to remove if removal is ever warranted and certain UL listings for the product may not apply. Precautions: Flintlastic SA Cap must be applied as part of a self-adhered system. It is not intended for use with hot asphalt, cold adhesives or torch-down applications. Roof decks must be structurally sound, dry and smooth, and meet or exceed minimum requirements of the deck manufacturer, local code and CertainTeed. Don't attempt application if ice, snow, moisture or dew is present. Surface to be bonded to must be clean, dry and free from any dust or deterrent to adhesion.Ambient temperature must be 50°F or above. Don't attempt installation on roofs without adequate slope and drainage. Additional specifications and precautions are contained in the CertainTeed Commercial Roof Systems Specifications. Storage and Flintlastic SA rolls must be stored above ground indoors and protected from the elements. Handling Rolls that are improperly stored or have been on hand for prolonged periods of time may lose their tack.Do not attempt to install rolls that do not exhibit an adequate bond. Warranties CertainTeed offers Limited (product only) and No Dollar Limit (NDL, product and workmanship)warranties. Warranty type and duration is dependent on roof system configuration and contractor selection. Only CertainTeed Gold and Silver Star Contractors are eligible to apply for NDL warranties on specific roof projects. For more information, see CertainTeed Commercial Roof Systems Specifications or contact Commercial Roofing Technical Services. Technical CertainTeed provides technical assistance in the design, selection, specification and Assistance and application guidelines for all CertainTeed Commercial Systems. Architectural and field representatives are available for consultation within each region. For more information, Services contact CertainTeed Commercial Roofing Technical Services at 800-396-8134 x2. CertainTeed Corporation ROOFING - SIDING • TRIM • DECKING • RAILING • FENCE • GYPSUM • CEILINGS • INSULATION SAI NT-GOBAI N 20 Moores Road Malvern,Pa 19355 Professional:800-233-8990 Consumer:800-782-8777 certainteed.com 07/17 CertainTeed Corporation,Printed in the USA,(ode No.COMM-169