601 Coastal Oak Ln POOL20-0014 6 of 8 APSP_1The Association ofPoo/ & Spa Professionals'
ANSVAPSPncc 15a ENERGY EFFICIENCY COMPLIANCE INFORMATION FOR RESIDENTIAL SWIMMING POOLS
PROJECT NAME:CONTRACTOR NAME h arK3ANO ADDRESS:
h).z
CONTRACTOR PHONE:
sheet was prepared by the APSP•15 Residenttal Swimming Pool and Spa Energy tfficjencv Standard Writing Committee of the Association o' Pool and Spa
Professionals (APSP). It is not part of the American National Standard ANSI/APSP/ICC-15a 2011 but is included for information only. Contractors should acquire and comply
wkh the ANSVAPSP/1CC•15a 2011 standard which can be purchased at www.apspvorg.
1. 55.2.1: Calculated pool volume
a. Ganons:; or 1. 49/9'
b. Calculated Gallons:(surface area) X (average depth) X 7.48 (gaVft A3)
2.552.1: Calculated filtration flow rate
(Pool vokzme + 360 or 36gpm whichever is larger)
3.55.5.1: Pipe sizing:
a. Minimum suction pipe diameter
(Enter the smattest pipe size from roble I with a 6 fps flow copocity the same or more thon item 2.)
b. Minimum suction branch pipe diameter 3b.
(Calculate: Item 2.(gpm) + Branch Pipes (quantity) bronch flow rote (gpm,l
Enter the smallest Ape size from roble I with 0 6 fps flow capacity the same or mote thon the calculated
suctbn branch flow rote.)
c. Minimum return pipe diameter
(Enter the smallest pipe size from Table I with 0 8fps flow capacity the same ot more than item 2.)
d. Minimum return branch pipe diameter
(Calculate: Item 2.(gpm) + Branch Pipes (quantity) bronch flow rote (gpm,l
Enter the smallest pipe size from roble with a 8 fps flow capacity the same ot mote thon the calculated
retwn branch ftw rote.)
4.55.4.1: Filter type and size:
a. Filter type: (Cartridge, DE, Sand)
b. Minimum filter area
(Cc/cuhte: item 2.(gpm) + filter factor (gpm/ftA2))
met factors: Cartridge•O.375, Sanda15, Diatomaceous Earth-2
5. 55.4.2: Backwash valve:Yes,No?5.(When using a bodwosh vob•e, enter result o/ item Jc or 2 inches whichever is lgtger)
6. Single-speed pump selection (when used):
95.1.1.53.1: For siro•speed pumps with total horsepower 0.99 or tind and enter a compliant pump the Pool Pump
pump a. Pump model
selection b. Total horsepower
7. Multi-speed pump selection (when used):
95.32.1: Pools øotlons o' less. select pump• from the database With a CurveA gem vow equul to Item 2 or less
Pod' ot more. select pump• from the dotgboje with a Curve( flow equal to item et
'Mufti-speed pumps must hove one speed listed that satisfies this requitement.
a. Pump model
b. Pump flow
6a.
6b.
7b,
gallons
gpm
inches
inches
inches
inches
sq. ft.
inches
or
gpm
L 5.322.' Applicable Curw A o.' C gp•n flow listed in database)
10/21/14 ANSt/APSV/iCC• Standard Wilting
ANSI/APSP/ICC 15 ENERGY EFFICIENCY COMPLIANCE INFORMATION FOR RESIDENTIAL SWIMMING POOLS
wrementS CheckCom nt
Heaters
Pool systems
Section
4.4.1.1
4.4.1.2
4.3.1.3
4.3.2
5.1.1
5.3.1
5.3.3
5.3.4
5.5.2
5.5.3
5.6
Heater has no pilot light
Readily accessible on-off switch mounted outside of the heater
No electric resistance heating unless for inground spa with tight fitting cover with R-6 insulation,
or for pool with 60% Of documented pool heating from on-site solar or recovered energy.
Heater efficiency: gas/oil fired heater efficiency at least 78%, heat pump COP at least 4.0
Pool filter pump listed in database
Pool filter pump with total horsepower 1.0 or more is multi-speed
Multi-speed pump controller programmed to default to the filtration flow rate when no auxiliary
pool loads are operating within 24 hours and programmed with temporary override capability for
servicing.
Single-speed pump controller capable of operating pump during off-peak electric demand.
Pipe before pump has at least 4 diameters of straight pipe.
System installed With solar. or setup for the future addition of solar heating equipment by
installing 18 inches of horizontal or vertical pipe after the filter and before a heater, or built-in or
built-u connections, or dedicated i to and from the pool.
Directional inlets for mixing pool water.
AMMAPSP/CC• Wt8iN Commott.e ion